2. Anova
  3. L1368

Anova L1368 Assembly Instruction

  • Hello! I've reviewed the Assembly Instructions for the Streetside L1368 and L1369 Contour Benches. This document provides detailed steps for assembling your new bench, including attaching the feet, securing the side supports, and ensuring proper leveling. I'm ready to answer any questions you may have about the assembly process or the components involved.
  • What tools are needed for assembly?
    What is recommended before assembling the nuts to the bolts?
    What is the importance of adhesive strips?
anovafurnishings.com
888.535.5005 tel
TOOLS NEEDED:
• 5/8" Open-end or box-end wrench
• Ratchet with 5/8" socket
• Level
Assembly Instructions
Streetside
L1368 - Streetside 4' Contour Bench
L1369 - Streetside 6' Contour Bench
BENCH COMPONENTS: ASSEMBLY HARDWARE: All hardware is stainless steel.
(1) Contour Bench Seat (1) Right Side
Bench End
(1) Le Side
Bench End
ASSEMBLY:
Inspect the shipping container contents for damage and to
determine that all components and hardware are present.
1.
2. Place the contour bench seat on the shipping packaging or
other so surface to avoid scratching the product.
3. Apply two adhesive strips to one of the plastic rectangular feet. Then rmly
apply the plastic rectangular foot to the metal foot of the bench support
aligning the holes in each. Repeat for each of the remaining feet.
NOTE: Before assembling the nuts to the bolts, it is
recommended that a light oil or petroleum jelly be applied
to the screw threads.
When viewing the bench seat from the end, the edge with
the hole near th end of the span is the seat portion and
the edge with the hole near the middle of the span is the
backrest portion.
1
(4) 7/16"-14
Hex Nut
(4) 7/16"Lock
Washers
(4) 7/16" Flat
Washers
Hole near middle of bench seat
denotes backrest portion.
Hole near end of bench seat
denotes seat portion.
Streetside 4' Contour Bench
(4) Plastic Rectangular Feet (8) Adhesive Strips
01/30/2018 Copyright 2018 ANOVA® Made in USA. 2
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
A A B B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 1/25/2018
DWG NO
TITLE
SIZE
D
SCALE
REV
0.16 : 1
16.83"
49.75"
16.83"
73.63"
.50"
.50"
A A B B
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
A A
B B
C C
D D
SHEET
1
OF
1
DRAWN
CHECKED
QA
MFG
APPROVED
dmetz 1/25/2018
DWG NO
TITLE
SIZE
D
SCALE
REV
0.16 : 1
16.83"
49.75"
16.83"
73.63"
.50"
.50"
4' FOOT MOUNT
6' FOOT MOUNT
16.83"
16.83"
49.75"
76.63"
O.50"
O.50"
Contour Bench Seat
Le Side Bench End
Right Side Bench End
Assembly and Replacement Parts
Hex Nut
Contour
Seat
Lock Washer
Flat Washer
Right Side
Bench End
Mounting Stud
4. Align the two threaded studs on the right side bench end with the mounting holes
on the appropriate end of the bench seat. Aer inserting the studs through the
mounting holes in the bench end, place a 7/16" at washer, 7/16" lock washer, and
7/16"-14 hex nut on the end of the stud and then tighten it nger tight.
Install a at washer, lock washer, and hex nut on the other stud in the same manner.
5. Repeat Step 4 by attaching the le side bench end to the other end of the contour
seat.
6. Tighten all of the hardware with the 11/16" open-end or box-end wrench or a
ratchet with an 11/16" socket while checking it with a level.
7. Move the assembled bench to the desired location.
8. Aer two weeks, retighten all of the hardware.
/