Q-tran iQ-CLP-LEAD Lead Wire To LED Board User manual

Brand
Q-tran
Model
iQ-CLP-LEAD Lead Wire To LED Board
Category
Strip lights
Type
User manual
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
iQ-CLP-LEAD
LEAD WIRE TO LED BOARD
Wire Gauge 22 -18 AWG
Voltage & Current 24VDC / 5A max
Wire side Wire side
Wire side
LED side
LED side
LED side
Insert bare wires into wire side of clip.
NOTE: Wire does not need to be pre-stripped.
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Clamp down LED strip between the top clear piece
and bottom piece using pliers.
Clamp down wires between the top clear piece and
bottom piece using pliers.
Insert LED strip into LED side of clip.
VERY IMPORTANT: Ensure polarity of LED lines up
with the polarity of the wire.
1
3
5
2
4
.5"
.96"
.30"
.50"
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
iQ-CLP-INLINE
LED BOARD TO LED BOARD
Wire Gauge 22 -18 AWG
Voltage & Current 24VDC / 5A max
Both sides LED
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Clamp down LED strip between the top clear piece
and bottom piece using pliers.
Insert LEDs into clip.
VERY IMPORTANT: Ensure polarity of LED strips
line up with each other.
Clamp down LED strip between the top clear piece
and bottom piece using pliers.
1
3
2
4
.5"
.78"
.30"
.50"
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
iQ-SNP-LEAD
LEAD WIRE TO LED BOARD
Wire Gauge 22 -20 AWG
Voltage & Current 24VDC / 5A max .17”
.61”
.45”
Wire side
LED side
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Both sides must be inserted before it is clamped
down.
Insert LED strip into LED side of clip.
VERY IMPORTANT: Ensure polarity of LED lines up
with the polarity of the wire.
Insert wire into wire side of clip.
NOTE: Wire does not need to be pre-stripped.
Clamp down wires and LED strip with pliers.
Black button on top should be flush with clear
surface.
1
3
2
4
.5"
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
iQ-SNP-INLINE
LED BOARD TO LED BOARD
Wire Gauge 22 -20 AWG
Voltage & Current 24VDC / 5A max
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Both sides must be inserted before it is clamped
down.
Insert LEDs into clip.
VERY IMPORTANT: Ensure polarity of LED strips
line up with each other.
Clamp down both LED strips.
Top Black button on top should be flush with clear
surface.
1
3
2
4
.5"
Both sides LED
.17”
.85”
.45”
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
Q-NECT-LEAD
LEAD WIRE TO LED BOARD
Wire Gauge 20 AWG
Voltage & Current 24VDC / 4A max
Q-NECT-01-LEAD Q-NECT-02-LEAD Q-NECT-03-LEAD
24”
0.61”
0.13”
0.31”
0.38”
TOOLS TO USE:
Pliers
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Press down on the terminals on each side to
puncture the strip.
Assembled view
Insert LED strip into LED side of the connector.
Slide the LED strip all the way until the end of the
strip touches the connectors wall.
VERY IMPORTANT: Ensure polarity of LED lines up
with the polarity of the wire.
NOTE: As a recommendation, wire with writing is
+24V and wire with grey dashes is negative.
1
3
2
.5"
24”
0.61”
0.46”
0.40”
0.13”
24”
0.63”
0.53”
0.48”
0.13”
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
Q-NECT-JUMP
CONNECT TWO LED BOARDS
Wire Gauge 20 AWG
Voltage & Current 24VDC / 4A max
Peel back .5" of adhesive on bottom of LED boards
to allow proper fit.
Press down on the terminals. Repeat on second
connector.
Assembled view
Insert LED strips into each end of connector.
VERY IMPORTANT: Ensure polarity of LED strips
line up with each other.
NOTE: As a recommendation, wire with writing is
+24V and wire with grey dashes is negative.
1
3
2
.5"
3”
0.61”
0.13”
0.31”
0.38”
Q-NECT-01-JUMP Q-NECT-02-JUMP Q-NECT-03-JUMP
3”
0.61”
0.46”
0.40”
0.13”
3”
0.63”
0.53”
0.48”
0.13”
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
Q-NECT-INLINE
LED BOARD TO LED BOARD
Voltage & Current 24VDC / 4A max
Peel back .5" of adhesive on bottom of LED boards
to allow proper fit.
Both sides must be inserted before it is clamped
down. Clamp down on each side.
Assembled view
Insert LED strips into each end of connector.
VERY IMPORTANT: Ensure polarity of LED strips
line up with each other. Ensure each board stops
in the middle of the connection. Metal contact must
puncture both boards.
1
3
2
.5"
0.13”
0.31”
0.38”
0.61”
0.13”
0.40”
0.46”
0.61”
0.48”
0.53”
0.67”
Q-NECT-01-INLINE Q-NECT-02-INLINE Q-NECT-03-INLINE
TOOLS TO USE:
Pliers
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
Q-NECT-SCREW-LEAD
LEAD WIRE TO LED BOARD
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Screw down.
NOTE: Do not overtighten.
Assembled view
Insert LED strip into LED side of the connector.
VERY IMPORTANT: Ensure polarity of LED lines up
with the polarity of the wire.
NOTE: Red wire is +24V, black wire is negative.
1
3
2
.5"
0.40”
0.26”
0.46” 0.48”
12”
Wire Gauge 22 AWG
Voltage & Current 24VDC / 4A max
TOOLS TO USE:
Screwdriver
© 2023 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | [email protected] | www.q-tran.com Specification subject to change. Rev-02-03-23
INSTALLATION Accessories - Lead & Inline Connectors
Q-NECT-SCREW-JUMP
CONNECT TWO LED BOARDS
Peel back .5" of adhesive on bottom of LED board to
allow proper fit.
Assembled view
Insert LED strips into each end of connector.
VERY IMPORTANT: Ensure polarity of LED strips
line up with each other.
1
3
2
.5"
0.40”
0.26”
0.46”
0.48”
12”
Wire Gauge 22 AWG
Voltage & Current 24VDC / 4A max
Screw down both connections. Repeat on second
connector.
NOTE: Do not overtighten.
TOOLS TO USE:
Screwdriver
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Q-tran iQ-CLP-LEAD Lead Wire To LED Board User manual

Brand
Q-tran
Model
iQ-CLP-LEAD Lead Wire To LED Board
Category
Strip lights
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents