Midmark Procenter Systems Installation guide

English-1

TP201 Rev. A

Applies to Models:

153839 (-003)

Special Tools:

none

Language of origin: English

003-2793-00 Rev. A (8/28/14)

Procenter Delivery System Cabinet Installation

Equipment Alert

Must provide Air, Water and Electrical supply for Delivery System.

Dental System must be installed per local plumbing and electrical codes.

If using a Illuminated Handpiece, 115V~, 0.6 amp is required.

Note: Electrical only needed if until has optional Illuminated Handpiece.

Cabinet / Utilities Requirements

• Minimum cabinet interior dimensions required are 10” wide x 17” deep x 25” high.

• Required: Cabinet floor opening or junction box (for mobile applications) to access utility connections and supplied regulators.

• A 1” diameter hole is required in cabinet toekick area to route the delivery system foot control into utilities area.

• Depending upon the delivery system options selected,

utilities area must include connections for air, water,

electrical supply and vacuum. All utilities must be installed

per local plumbing and electrical codes by a licensed

contractor. If using Illuminated Handpiece option,

a medical-grade receptacle and circuit rated at 115V~,

60 Hz, 0.6 amp is required.

DA2638

Style G

midmark.com

English-2

TP201 Rev. A

4227

1-1/8”

Handpiece Pilot

Tubing Hole.

Step 1: Mount Holder bar for instruments.

A) Remove two #10 screws provided in instrument mounting bar.

B) Using the two #10 screws mount instrument bar to door.

C) Route handpiece pilot tubing through hole in door near holders

as shown.

Note: See door preparation if holes are not provided..

Door Preparation...

A) Mark mounting locations on cabinet. Must be located in front of control tray panel.

Installer must add hole in cabinet door or provide opening at the bottom of the

door (2” minimum) for instrument tubing to go inside cabinet if not provided.

B) Drill two 7/32” holes at 1 1/8” spread if not provided.

1-1/8”

4”

Center of Door

2-5/16”

3-1/2”

003-2793-00

Style G

midmark.com

English-3

TP201 Rev. A

Step 3: Mount Water Bottle Assembly. (if applicable)

A) Mark mounting locations in cabinet. Must be located across from control

tray or preferably inside door.

B) Drill 1/8” pilot holes (refer to dimensions in picture).

C) Mount water bottle assembly using four #8 wood screws provided.

Note: May use bracket to mark pilot hole spread.

Water Bottle

Mounting Bracket

Solids Collector

1-1/2”

3-1/2”

1-3/8”

Step 2: Mount Solids Collector.

A) Mark mounting locations in cabinet. Must be located across

from control tray.

B) Drill two 1/8” pilot holes (refer to dimensions in picture).

C) Mount solids collector using two #8 wood screws provided.

Note: May use bracket to mark pilot hole spread.

003-2793-00

Style G

midmark.com

English-4

TP201 Rev. A

DA2604

Cabinet Members

#8 x 3/4” Screws

Drawer Members

Assembled View

Hole Position of

Drawer Member

Step 5: Slide installation.

A) Drill six 3/32 pilot hole locations for cabinet members with template

provided with Install Kit (002-1359-00) if installing in custom cabinet.

B) Screw slide cabinet members to cabinet.

Step 4: Assembling control tray to slides.

A) Screw slide drawer members to control tray assembly.

#10 x 3/8” Screws

003-2793-00

Style G

midmark.com

English-5

TP201 Rev. A

Step 6: Slide installation.

A) Position bearing race at end of each slide that is attached to cabinet.

B) Align top and bottom slides on control tray with slides on cabinet.

Move carefully into position.

Step 7: Slide installation.

A) Route handpiece and syringe tubing from control tray through cutout

in door to appropriate holder on holder bar.

B) Loosen screws holding bracket to door, slip bracket off, route

tubing through and replace bracket onto door. The tubing must be

prevented from dragging of the floor outside the cabinet.

Bearing Race

003-2793-00

Style G

midmark.com

English-6

TP201 Rev. A

Step 8: Umbilical Tubing (for optional mobile application).

A) Take the end of the umbilical with the quick connects on the internal tubing

and thread one umbilical cuff onto the end about 12” (this can be adjusted

once umbilical is secured to the cabinet).

B) If not already provided in the cabinet, drill a 2” Dia hole in the sides of the

cabinet where the umbilical will enter the cabinet.

C) Feed any electrical Flexible conduit through large corrugated tubing.

D) Route umbilical assembly (with electrical whip included) through the

cutouts in cabinet.

E) Use the other umbilical cuff to secure the tubing to the cabinet.

Step 9: Umbilical Tubing to cabinet (for optional mobile application).

A) Route umbilical assembly (with electrical whip included) through the cutouts in the

cabinet into compartment with the control tray (if applicable).

B) Use the other umbilical cuff to secure the tubing to the cabinet.

12”

Flat side of

Threaded Cuff

2nd Cuff

Flat side

003-2793-00

Style G

midmark.com

English-7

TP201 Rev. A

Step 10: Handpiece Tubing Connections.

A) Take numbered red and purple tubing from control tray and connect to

numbered pilot tubing from handpieces.

Step 11: Water Bottle Assembly Tubing

Connections (if applicable).

A) Take the yellow tubing from control tray and pair with

the yellow tubing from water bottle assembly.

B) Trim the yellow tubing 18” from control tray and

connect the tubing from the control tray to the yellow

tubing from water bottle assembly.

C) Then tee excess yellow tubing that was trimmed off

onto tee’d assembly to route from the tee connection

to the air regulator.

D) Take the orange tubing from control tray and pair with

the orange tubing from water bottle assembly.

E) Trim the orange tubing 18” from the control tray and

connect the tubing from control tray to the orange

tubing from the water bottle assembly.

F) Then tee excess orange tubing that was trimmed off

onto tee’d assembly to route from the tee connection

to the foot control switch.

G) Connect blue tubing from control tray to blue tubing

from water bottle assembly.

H) Install water bottle.

Note: If water bottle assembly is not configured with unit, yellow and

orange tubing will go from the control tray to the air regulator and the

foot control switch.

Step 12: Solids Trap Tubing Connections.

A) Route corrugated vacuum tubing from vacuum supply line to solids trap.

B) Route HVE and SE tubing into cabinet through cutout in door/drawer,

then through bracket on the back of the door then hook up to solids trap.

Note: This may require removing red caps from HVE fitting on solids trap.

003-2793-00

Style G

midmark.com

English-8

TP201 Rev. A

Step 14: Install Air and Water Regulators.

A) Refer to diagrams in this manual for other air and water connections.

Step 13: Install foot control and make tubing connections.

A) Route tubing to cabinet. On mobile models, route thru the cutout in the bottom of the cabinet. On static models,

route thru the grommet in the front of the toekick.

B) Make air and water connections according to tubing diagrams on the following pages.

Water Regulator

Air Regulator

Step 15: Organize Tubing.

A) Organize tubing from water bottle assembly and route through

supplied cable connectors inside the cabinet.

003-2793-00

Style G

midmark.com

English-9

TP201 Rev. A

153839

(-001 Thru -004)

Control

Panel

Schematic

DA2613

Handpiece

Drive Air

Handpiece

Coolant

Air

Syringe

Water

Syringe

Air

Drive Air

Pressure Gauge

Syringe

Tubing

1/8"

Yellow

Air / Oil

Separator

Check

Valve

Check

Valve

Handpiece

Drive Air

Handpiece

Drive Air

Handpiece

Coolant

Water

Handpiece

Coolant

Water

Handpiece

Coolant

Water

Kink

Valve

Kink

Valve

1/8" Blue

1/8"

Green

CW- Coolant Water

DA - Drive Air

CA - Coolant Air

Pilot

Air

From

Pilot

Air

To

Doctor's

Instrument

Handpiece

Valves

Pilot Air from

Master Switch on

Water Bottle Assy.

1/8"

Blue

1/8" Yellow

1/8" Green

1/8" Orange

1/8" Red

1/4" Clear

1/8"

Clear

1/8" Red

1/8" Orange

1/8"

Purple

1/8"

Grn

1/8"

Orange

1/4"

Clear

1/8" Red

1/8"

Clear

1/4"

Clear

1/4" Clear

1/8"

Wht

Flush Valve Pilot

Air (Control Panel)

Handpiece Coolant

Water Pilot Air

(Cabinet Base)

Check

Valve

CA

CW

DA

1/8"

Blue

1/8"

Blue

1/8"

Wht.

1/8"

Blue

1/4" Clear

1/8"

Clear

Exhaust Air

Exhaust

Air

1/8"

Blue

1/8"

Blue

1/8"

Wht

CA

CW

DA

1/4"

Clear

1/4"

Grey

Kink

Valve

1/4" Clear

1/8"

Purple

1/8"

Wht.

1/8" Orange

CA

CW

DA

1/4"

Clear

1/4"

Grey

1/4" Clear

1/8"

Wht.

1/8"

Purple

1/8"

Blue

1/8" Orange

1/4"

Clear

1/8"

Grn

Exhaust Air

Exhaust

Air

1/8"

Clear

1/8"

Wht

1/8"

Blue

1/8" Blue

1/8" Green

Manifold

(Air)

1/8"

Blue

1/8"

Grn

Manifold

(Water)

1/4"

Clear

1/8" Blue

1/8"

Wht

1/4" Clear

1/4"

Clear

1/4"

Clear

1/4"

Clear

1/8"

Red

1/8"

Purple

1/8"

Clear

1/8" Clear

Syringe

Supply Air

Instrument

Water Supply

Handpiece

Drive Air

Doctor's Syringe

Master

On/Off

Valve

Handpiece

Coolant Air

Supply

1/8 Red

1/8 Purple

Bleed

Air to Master

Switch

Pilot Air From

Master Switch

OFF

ON

003-2793-00

Style G

midmark.com

Color Page

English-10

TP201 Rev. A

003-2793-00

Style G

midmark.com

Color Page

English-11

TP201 Rev. A

003-2793-00

Style G

midmark.com

Color Page

English-12

TP201 Rev. A

DA2474-1

153839 (-001 thru -004)

Water Bottle Assembly

1/8 Blue

City

Bottle

Water

Selector

Valve

30 PSI

Bottle

Water

City

Bottle

1/8 Brown

30 PSI

Air

1/8 Blue

Instrument

Air Supply

Instruments

Water Supply

30 PSI City Water

To / From

Air - Water

Junction

(located in

cabinet

base or

control

panel)

80 PSI Air

80 PSI Syringe Air

1/8

Clear

1/8 Brown

1/8 Yellow

1/8

Brown

Ribbed

Side

30

PSI

Bottle

Water

Instrument Water Supply

Out

Push

Flush Valve

(N.C.) 2-Way

Manual

Momentary

1/8 Orange

1/8 Yellow

1/8 Orange

1/8 Yellow

1/8 Blue

Flush Valve Pilot Air

(Control Panel)

Syringe Supply Air

Double

Pinch

Valve

Rib on Air Side

(Yellow Tubing)

Water

Air

1/8

Blue

To Assistant's

Instrument

Syringe

1/8

Blue

1/8

Yellow

1/8

Blue

In-Line

Regulator

003-2793-00

Color Page

Style G

midmark.com

Midmark Procenter Systems Installation guide

Midmark Procenter Systems Installation guide

Related papers

Other documents