English-1
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
VA1702i
Equipment Alert
Midmark recommends anchoring
table to the floor when using in
the middle of office.
003-1854-00 Rev. H (6/12)
Note
Midmark recommends to use 2 installers for this procedure.
Installer may bolt table to cabinet or wall.
Wet or Dry Treatment Table Installation
Casework (Flush Mount) & Wall Mount
Applies to Models:
8003 (all)
8007 (all)
Special Tools:
none
Wet Table Dimensions
Attention
Midmark recommends using a licenced
professional to install required plumbing.
Dry Table Dimensions
VA1517-1i
Note
This install guide covers two mounting options.
Refer to Appropriate pages for Installation.
Wall Mount
Flush Mount
Flush Mount go to Page 2.
Wall Mount go to Page 3.
Center of Room
Center of Room go to Page 4.
Style A
midmark.com
English-2
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
Chase Installation
Step 2 : Refer to page 4 for Table
Plumbing Installations.
Step 1: To install table, use hardware included with chase cabinet.
(#10 screws, washers and nuts)
Note
Refer to chase installation manual
for mounting hole locations.
Style A
midmark.com
English-3
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
VA1705i
Standard Installation
Step 1: Mount corner brackets to
inside of cabinet.
Step 2: Open door on table and
secure to corner brackets.
Step 3: Refer to page 4 for Table
Plumbing Installations.
Style A
midmark.com
English-4
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
VA1401i
Step 1: Find center of each stud.
Note: If stud can not found, go to Step 5.
Step 3: Secure to wall using
washers and screws
being sure to hit studs.
Step 2: Slide table
into position.
Step 4: Refer to page 4 for Table Plumbing Installations.
Step 5: Slide table into position and
mark hole locations on wall.
Step 6: Slide table away from wall and
drill holes using 3/16” bit.
Step 8: Slide cabinet back to wall, align
with anchors and secure to wall
with screws and washers.
Step 7: Remove screws from
anchors and place
anchors in wall.
Step 9: Refer to page 4 for Table
Plumbing Installations.
Wall Mount Installation
Style A
midmark.com
English-5
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
VA1299i
1 1/2" (max.)
(3.8 cm)
LOWER
TABLE
TABLE
RAISE
To level table (if needed)...
Step 2: Pull drawer up and out to
remove from slides.
To level table (if needed)...
Step 1: Pull drawer out then carefully pull
outside of drawer out to release
drawer slide tabs from drawer.
To level table (if needed)...
Step 3: Level table
and re-install
drawer (s).
Step 4: To install faucet with or without
sprayer follow the manufacturer’s
instructions.
Step 5: Install drain, tail pipe and hair trap.
Note: The debris trap is not intended to replace a P-trap. The
debris trap is a plumbing device that has a removable strainer
intended for installation between the tub drain and before the
standard P-trap. Midmark does not supply the P-trap.
P-Trap
NOT Supplied
Drain
Plumbing Installation
Style A
midmark.com
/