Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Integra™ Operatory Cabinetry - Side Cabinetry
Midmark
Brand
Midmark
Model
Integra™ Operatory Cabinetry - Side Cabinetry
Type
Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions for your dental operatory. Its adjustable shelves, drawers, and doors allow you to customize the storage space to meet your specific needs. The durable laminate construction ensures longevity, while the sleek design complements any dental office décor. Keep your supplies organized and within reach with this efficient and stylish cabinetry system.

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions for your dental operatory. Its adjustable shelves, drawers, and doors allow you to customize the storage space to meet your specific needs. The durable laminate construction ensures longevity, while the sleek design complements any dental office décor. Keep your supplies organized and within reach with this efficient and stylish cabinetry system.

1
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-1942-00 Rev. B (11/2/11)
18” & 24” Sink Unit Installation
Applies to Models:
OSC018S
OSC024S
Special Tools:
Level
1/4” deep well socket
Caulking Gun
Belt Sander
OSC018S (18’ Sink Unit) - shown
OSC024S (24’ Sink Unit)
DA2166i
midmark.com
Style A
2
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2220i
Wall
WALL
FLOOR MOUNT SERVICE
HOT
COLD
3/4 in (1.9 cm) Hole
1/2 in NPT Water Pipe
Stub out 1 in (2.5 cm) Min.
2-1/2 in (6.4 cm) Max from
finished floor surface.
Use 1/2 in male NPT fitting
on end of stubs for connections
to shut-off valves. Install 1/2 in
inlet x 3/8 in O.D. outlet angle
shut-off valves.
Waste drain 2 in (5.1 cm) hole
1.5 in (3.8 cm) drain pipe
3 in
7.6 cm
4 in
10.2 cm
Wall
Note
All plumbing must be made by a licensed
plumbing contractor and conform to local, city,
and national codes pertaining to the installation.
18” Floor Layout (as applicable)
24” Floor Layout (as applicable)
midmark.com
Style A
3
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2219i
Waste drain
2 in (5.1 cm)
hole
1-1/2 in drain
pipe
HOT
COLD
FLOOR
3/4 in (1.9 cm) Hole
1/2 in NPT Water Pipe
Stub out 1-3/4 in (4.5 cm) Min.
3-3/4 in. (9.5 cm) Max from
finished wall surface .
Use 1/2 in male NPT fittings on end of
stubs for connections to shut-off valves.
Install 1/2 in inlet x 3/8 in O.D. outlet
angle shut-off valves.
WALL MOUNT SERVICE
16-1/4 in (41.3 cm)
3 in
7.6 cm
13-1/4 in (33.7 cm)
18” Wall Layout (as applicable)
Note
All plumbing must be made by a licensed
plumbing contractor and conform to local, city,
and national codes pertaining to the installation.
24” Wall Layout (as applicable)
midmark.com
Style A
4
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2168i
DESIRED POSITION OF EDGE OF UNIT
WALL
Storage
RAISE
CABINET
LOWER
CABINET
1 1/2" (max.)
(3.8 cm)
Equipment Alert
Do not adjust leveling screws more then
1 1/2” (3.8 cm) to prevent lose of stability.
POSITIONING & LEVELING
Step 1: Remove bottom
panel from cabinet.
Step 2: Adjust leveling screws
to fully lowered position
and move cabinet to
desired position.
Step 3: Level cabinet with
leveling screws.
18’ Sink Unit - SHOWN
midmark.com
Style A
5
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
CONNECTING ADDITIONAL UNITS
& COUNTER TOP INSTALLATION
DA2169i
Note
If necessary, sand
counter top to form
to wall.
Step 1: If necessary, level and
connect any additional
storage units.
Step 2: Position counter top so it
extends 3/8” (0.95 cm) to
1/2” (1.3 cm) over each
end of cabinet(s) and secure
with #10 x 5/8” screws.
Special hex bolts
(#10-24 x 3/4”)
18’ Sink Unit - SHOWN
midmark.com
Style A
6
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2171i
SINK INSTALLATION &
PLUMBING CONNECTIONS
LAMINATE TOP SHOWN
Step 1: Caulk around perimeter of
hole, then position sink.
Step 4: Refer to the instructions with
Tapmaster™ faucet controller
for installation procedure.
Step 3: Install faucet and soap
dispenser using instructions
included with those items.
Note
All plumbing must be made by a licensed
plumbing contractor and conform to local,
city, and national codes pertaining to the
installation.
Equipment Alert
When installing a sink, Midmark
recommends securing cabinet to wall.
Failure to comply may result in damage
to plumbing connections.
Step 2: Secure sink with bracket kits
included with sink.
18’ Sink Unit - SHOWN
midmark.com
Style A
7
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
DA2170i
DOOR ADJUSTMENT
Vertical Adjustment
A) Loosen both screws.
B) Move up or down.
C) Retighten screws.
Horizontal Adjustment
A) Turn cam screw to move
panel side to side.
Depth Adjustment
A) Turn cam screw to move
panel front to back.
18’ Sink Unit - SHOWN
midmark.com
Style A
8
© 2011 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
midmark.com
Style A
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Integra™ Operatory Cabinetry - Side Cabinetry
Midmark
Brand
Midmark
Model
Integra™ Operatory Cabinetry - Side Cabinetry
Type
Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions for your dental operatory. Its adjustable shelves, drawers, and doors allow you to customize the storage space to meet your specific needs. The durable laminate construction ensures longevity, while the sleek design complements any dental office décor. Keep your supplies organized and within reach with this efficient and stylish cabinetry system.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents