Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Brand: Midmark

Model: Integra™ Operatory Cabinetry - Side Cabinetry

Category: Sanitary ware

Type: Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions for your dental operatory. With adjustable shelves, pull-out trays, and swing-out tubs, you can customize the cabinet to meet your specific needs. The durable laminate construction ensures long-lasting use, while the easy-to-clean surfaces help maintain a hygienic environment.

003-1930-00 Rev. B (1/12)

OSC055S-L (55” LH Sink / Storage Unit

OSC055S-R (55” RH Sink / Storage Unit

OSC064S-L (64” LH Sink / Storage Unit

OSC064S R (64” RH Sink / Storage Unit

55”, 64” Square Sink / Storage Unit Installation

Applies to Models:

OSC055S, OSC064S

Special Tools:

Level

1/4” deep well socket

Caulking Gun

Belt Sander

OSC064S-L (Shown)

DA2186i

NextNext

BackBack

midmark.com

Style A

Note

• All plumbing must be made by a licensed plumbing contractor and

conform to local, city, and national codes pertaining to the installation.

LEFT CABINET DIMENSIONS

DA2225i

WALL

FLOOR MOUNT SERVICE

HOT

COLD

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1 in (2.5 cm) Min.

2-1/2 in (6.4 cm) Max from

finished floor surface.

Use 1/2 in male NPT fitting

on end of stubs for connections

to shut-off valves. Install 1/2 in

inlet x 3/8 in O.D. outlet angle

shut-off valves.

Waste drain 2 in (5.1 cm) hole

1.5 in (3.8 cm) drain pipe

3 in

7.6 cm

4 in

10.2 cm

Waste drain

2 in (5.1 cm)

hole

1-1/2 in drain

pipe

HOT

COLD

FLOOR

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1-3/4 in (4.5 cm) Min.

3-3/4 in. (9.5 cm) Max from

finished wall surface .

Use 1/2 in male NPT fittings on end of

stubs for connections to shut-off valves.

Install 1/2 in inlet x 3/8 in O.D. outlet

angle shut-off valves.

WALL MOUNT SERVICE

16-1/4 in (41.3 cm)

3 in

7.6 cm

13-1/4 in (33.7 cm)

NextNext

BackBack

midmark.com

Style A

RIGHT CABINET DIMENSIONS

Note

• All plumbing must be made by a licensed plumbing contractor and

conform to local, city, and national codes pertaining to the installation.

DA2226i

WALL

FLOOR MOUNT SERVICE

HOT

COLD

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1 in (2.5 cm) Min.

2-1/2 in (6.4 cm) Max from

finished floor surface.

Use 1/2 in male NPT fitting

on end of stubs for connections

to shut-off valves. Install 1/2 in

inlet x 3/8 in O.D. outlet angle

shut-off valves.

Waste drain 2 in (5.1 cm) hole

1.5 in (3.8 cm) drain pipe

3 in

7.6 cm

4 in

10.2 cm

Waste drain

2 in (5.1 cm)

hole

1-1/2 in drain

pipe

HOT

COLD

FLOOR

3/4 in (1.9 cm) Hole

1/2 in NPT Water Pipe

Stub out 1-3/4 in (4.5 cm) Min.

3-3/4 in. (9.5 cm) Max from

finished wall surface .

Use 1/2 in male NPT fittings on end of

stubs for connections to shut-off valves.

Install 1/2 in inlet x 3/8 in O.D. outlet

angle shut-off valves.

WALL MOUNT SERVICE

16-1/4 in (41.3 cm)

3 in

7.6 cm

13-1/4 in (33.7 cm)

NextNext

BackBack

midmark.com

Style A

DA2174i

Step 1: Lift or push down release

levers (one per side) and

slide out drawer assembly.

Step 1: Pull drawer outward

until it hits stop.

Step 2: Pull sides of drawer outward

while lifting to free back of

drawer from hooks and remove.

2” Metal Frame Drawers

Writing Surface Assembly

All Molded Drawers

DRAWER REMOVAL

(If Required for Access)

NextNext

BackBack

midmark.com

Style A

DA2188i

DESIRED POSITION OF EDGE OF UNIT

LOWER

CABINET

1 1/2" (max.)

(3.8 cm)

RAISE

CABINET

SINK / STORAGE UNIT INSTALLATION

Equipment Alert

Do not adjust leveling screws more then

1 1/2” (3.8 cm) to prevent lose of stability.

Step 1: Remove bottom

panels from cabinet.

Step 2: Adjust leveling screws

to fully lowered position

and move cabinet to

desired position.

Step 3: Level cabinet with

leveling screws.

NextNext

BackBack

midmark.com

Style A

DA2189i

SINK INSTALLATION &

PLUMBING CONNECTIONS

LAMINATE TOP SHOWN

Step 1: Caulk around perimeter of

hole, then position sink.

Step 5: Refer to the instructions with

Tapmaster™ faucet controller

for installation procedure.

Step 4: Install faucet and soap

dispenser using instructions

included with those items.

Note

All plumbing must be made by a licensed

plumbing contractor and conform to local,

city, and national codes pertaining to the

installation.

Equipment Alert

When installing a sink, Midmark

recommends securing cabinet to wall.

Failure to comply may result in damage

to plumbing connections.

Step 3: If required, caulk around

perimeter of hole and

install waste ring.

Step 2: Secure sink with bracket kits

included with sink.

NextNext

BackBack

midmark.com

Style A

DA2190i

DOOR HINGE ADJUSTMENT

Vertical Adjustment

A) Loosen both screws.

B) Move up or down.

C) Retighten screws.

Horizontal Adjustment

A) Turn cam screw to move

panel side to side.

Depth Adjustment

A) Turn cam screw to move

panel front to back.

Note

Doors should be adjusted for the

gap specified on the illustration.

NextNext

BackBack

midmark.com

Style A

DA2229i

Adjusting Shelf

Remove shelf (not shown) and relocate

shelf brackets at desired position.

Relocating Pull-Out Shelf

Remove six screws from shelf slides and

relocate pull-out shelf in desired position.

Relocating Swing-Out

Tub and/or Shelf

A) Loosen screw so the shelf or tub is loose.

B) Move shelf forward and out to remove. Remove

screw, then re-install at desired location (do not

tighten). Position shelf, then tighten screw.

NextNext

BackBack

midmark.com

Style A

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Brand: Midmark

Model: Integra™ Operatory Cabinetry - Side Cabinetry

Category: Sanitary ware

Type: Installation guide

Download PDF

report

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Related papers

Other documents