Daktronics DVN-3002 Series Installation guide

Brand: Daktronics

Model: DVN-3002 Series

Type: Installation guide

Daktronics DVN-3002 Series offers versatile solutions for various applications. With its integrated clip attachment system, it allows for seamless panel integration and easy serviceability. The direct attachment option using M6 nutserts provides secure mounting. Installation is simplified with clear guidelines for bottom, middle, and top row clip orientations and attachment procedures. The series ensures precise alignment and stability with adjustable Z-axis for each clip.

DVN-3002 Series Panel Installation Quick Guide Page 1 of 2

DD5147183

Rev 01

11 November 2022

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Attach a display by using either the direct attachment or integrated clip

attachment. Refer to the contract-specic Shop Drawing for additional

details.

Direct Attachment

An M6 nutsert is available for direct attachment to substructure with the

supplied M6x1 - 20 mm hex-head bolts (Daktronics part number

HC-3464941). Refer to Figure 1. Insert one M6 bolt in each of the lower

corners on each panel. Insert one M6 bolt in each of the upper corners on

the bottom row of panels only. Refer to Figure 2. Refer to the contract-

specic Shop Drawing.

Integrated Clip Attachment

Panels have four cutouts capable of attaching an optional integrated clip.

Refer to Figure 3. Clips pass through the cutout and attach with a threaded

M6 bolt. There is a 1/2" slot for Z-axis adjustment. Refer to Figure 4.

Note: Integrated clips ship separately from the display.

The bottom row of panels requires one integrated clip per corner. Panels

above the bottom row require one integrated clip in each of the upper

corners. Prepare each panel based on its location in the display. Refer to

Figure 5.

Figure 1: Attachment

Hardware

Figure 2: Attachment

Locations

Figure 3: Corner Detail (Side)

1: Integrated clip

2: Threaded M6 bolt

3: Backsheet tab

1: 1/2" Adjustment slot

2: M6 for vertical attachment

3: Pilot hole for M5 self-tapping

screw

Figure 4: Corner Detail (Top)

Figure 5: Tab Removal and Clip Orientation by Row

Clip Orientation

Bottom Row Clip Orientation

1. Panels on the bottom row require four integrated clips. Use a at

screwdriver to pry the tab out of the chassis backsheet in the lower two

corners. Refer to Figure 5 and Figure 6.

2. Once the backsheet tabs have been removed, ip the orientation of

the lower integrated clips toward the inside of the panel so that they

do not show below the bottom border. Refer to Figure 7.

Figure 6: Backsheet Tab Removal

Figure 7: Lower Clips on Bottom Row

3. Install an M6X10 hex button head cap screw (Daktronics part number

HC-2003) through the chassis nutsert and threaded hole in the

integrated clip. Set the Z-axis adjustment so that the clip is tight against

the panel. This dimension can be adjusted from beneath after upper

panels are installed. Refer to Figure 8.

4. Orient the upper clips so they show above the top border, allowing the

clip to cradle and provide an attachment point for upper panels.

Backsheet tabs should remain attached. Refer to Figure 5 and Figure 9.

5. Repeat Step 3 for the upper clips.

Note: Pilot holes are recommended to aid in placement during

installation. If standard 1/4"-14 screws are being used, use a pilot

hole size of 13/64" [5.16 mm]. If alternative screws are being used,

nd the correct pilot hole size per the hardware specied on

the contract-specic Shop Drawing.

Middle Rows Clip Orientation

1. Panels in the middle rows each require two integrated clips, one in

each top corner. Backsheet tabs should remain attached. Orient the

clips so they show above the top of the panel, allowing the clip to

cradle and provide an attachment point for the panels above. Refer to

Figure 5 and Figure 9.

2. Install a M6x10 hex button head cap screw through chassis nutsert and

threaded hole in the integrated clip. Set the Z-axis adjustment so that

the clip is tight against the panel. Refer to Figure 8.

Figure 8: Remove Backsheet Tab for Screw Clearance

Figure 9: Upper Clips on Bottom and Middle Rows

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Top RowMiddle RowsBottom Row

1 2

Backsheet tab Backsheet tab removed

Button head cap screw

DVN-3002 Series Panel Installation Quick Guide Page 2 of 2

DD5147183

Rev 01

11 November 2022

201 Daktronics Drive

Brookings, SD 57006-5128

www.daktronics.com/support

800.325.8766

Upper Row Clip Orientation

1. Panels on the top row require two integrated clips. Use a at

screwdriver to pry the tab out of the chassis backsheet in the upper

two corners. Refer to Figure 5 and Figure 6.

2. Once the backsheet tabs have been removed, ip the orientation of

the upper integrated clips toward the inside of the panel so that they

do not show above the top border. Refer to Figure 10.

3. Install a M6x10 hex button head cap screw through the chassis nutsert

and threaded hole in the integrated clip. Refer to Figure 8.

Panel Installation

Note: Use a level throughout this section to verify each panel is level in

the X and Y directions.

Bottom Row Attachment

Note: This procedure is easiest with three people.

1. Prepare for attachment to the substructure by stitching two panels

together with M6x1 - 20 mm hex ange interconnect bolts. If the display

is three panels wide, prepare by stitching three panels together. Ensure

that panels are ush at the top and face. Refer to Figure 11.

2. Position the rst panels in the bottom-center of the display. Verify the

location of the panel relative to the structure.

Figure 10: Upper Clips on Upper Row

Figure 11: Install First Panel

Figure 12: Interconnect Hardware

3. Install the two M6 interconnect bolts

through the left perimeter of the

panel into the nutsert of the

adjacent panel. Hand-tighten the

bolts as much as possible, then use a

hand tool to tighten an additional 1

to 1-1/2 turns. Adjust the panels until

they are plumb and level. Refer to

Figure 12 and Figure 13.

4. After the center panels have been

attached, work outward. Stitch

adjacent panels together with M6

interconnect bolts, verify plumbness,

then attach to substructure with

screws.

Middle Rows Attachment

1. After the rst row has been

attached, position the next

panels above the bottom

center. Attach the panels

vertically using the provided

M6 interconnect bolts.

Hand-tighten the bolts as

much as possible, then use

a hand tool to tighten an

additional 1 to 1-1/2 turns.

Refer to Figure 12 and

Figure 13.

2. Use a level to verify the

panels are all plumb, at,

and level to each other in

the X, Y, and Z directions.

Adjust Z-axis as needed.

After verifying, tighten

down the hardware in all

applicable corners.

3. Continue to build outwards

to ll each row, then

upwards to the next row.

Figure 13: Interconnect Hardware and

Flushness Verication

Top Row Attachment

1. Continue attaching panels up to the top row. Refer to Figure 14.

2. Ensure that the top row of panels is level and plumb. If using the

Integrated Clip Attachment method, ensure that the top row of

integrated clips is oriented to not show above the top border.

3. Tighten the M6x1 - 12 mm screws on top of each panel. Panels above

the rst row require one screw in each of the top corners.

Figure 14: Install Panels Outward and Upward

Daktronics DVN-3002 Series Installation guide

Daktronics DVN-3002 Series Installation guide

Daktronics DVN-3002 Series Installation guide

Related papers

Other documents