Daktronics GALAXY ECCB Series Operating instructions

Type
Operating instructions
201 Daktronics Drive
Brookings, SD 57006-5128
www.daktronics.com/support
800.325.8766
GALAXY
®
ECCB DISPLAY
INSTALLATION AND
OPERATION MANUAL
P1676
DD2885557
Rev 10
20 March 2020
Copyright © 2020
All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no
responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied
in any form or by any means—graphic, electronic, or mechanical, including photocopying, taping, or information
storage and retrieval systems—without written permission of the publisher.
Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference
This device must accept any interference
received, including interference that may cause
undesired operation.
Warning: Risk of re or electric shock. LED Retrot
Kit installation requires knowledge of sign electrical
systems. If not qualied, do not attempt installation.
Contact a qualied electrician.
Warning: Risk of re or electric shock. Install this kit only
in host signs that have been identied in the installation
instructions and where the input rating of the retrot kit
does not exceed the input rating of the sign
Warning: Risk of re or electric shock. Installation of this
LED retrot kit may involve drilling or punching of holes
into the structure of the sign. Check for enclosed wiring
and components to avoid damage to wiring and
electrical parts.
Warning: To prevent wiring damage or abrasion, do not
expose wiring to edges of sheet metal or other sharp
objects.
Industry Canada Regulatory Information
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à
la norme NMB-003 du Canada.
Inquiries
Contact Daktronics with any questions regarding our
product compliance.
Mail:
Daktronics
201 Daktronics Dr.
Brookings, SD 57006 USA
Phone:
800-325-8766
Website:
www.daktronics.com
– i –
Table of Contents
1 Introduction �����������������������������������������1
Limitation of Liability ..................................1
Contact Information .................................1
Model Number Guide ...............................1
Retrot Kit Parts ..........................................2
2 Installation Preparation ����������������������3
Pre-Installation Checklist ...........................3
Structure Requirements .............................3
3 Display Installation������������������������������4
Display Installation Preparation................4
Display Installation .....................................4
4 Electrical Installation ��������������������������6
Electrical Installation Preparation ............6
Electrical Requirements ............................6
Main Disconnect .......................................6
Electrical Installation ..................................7
Grounding ..................................................8
5 System Start-Up Procedure ����������������9
Boot Sequence ..........................................9
Start-Up Checklist ......................................9
6 Display Communication ������������������10
OS Requirements .....................................10
Display Login ............................................10
Change Password ...................................12
Create Messages.....................................13
Change Message Order .........................16
Options Menu ..........................................17
Display Information ������������������������������17
Date and Time ��������������������������������������17
Time Zone ...........................................17
Time Format .......................................18
Brightness ����������������������������������������������19
Test Patterns ������������������������������������������19
Temperature ������������������������������������������20
Temperature Offset ...........................20
Temperature Format .........................20
7 Display Maintenance �����������������������22
Internal Display Access ...........................22
Ventilation System ...................................22
Fans �������������������������������������������������������� 22
Display Face Cleaning ............................23
Wet Cleaning Process ��������������������������23
Dry Cleaning Process ���������������������������23
8 Display Troubleshooting �������������������24
Power and Signal Routing ......................24
Power Routing ���������������������������������������24
Signal Routing ���������������������������������������25
Controller Diagnostics .............................25
Module Diagnostics .................................26
Module Self-Test �����������������������������������26
Troubleshooting .......................................26
Module and LED Problems ������������������� 26
Temperature Problems ������������������������� 27
9 Replacement Parts List ���������������������28
10 Replacing Parts ���������������������������������29
Module Replacement .............................29
Power Supply Replacement ..................29
Controller Replacement .........................29
Temperature Sensor Replacement .......30
Wi-Fi Router and Antenna Replacement
...................................................................30
Install New Access Point and Antenna .31
11 Daktronics Exchange and Repair &
Return Programs ��������������������������������33
Exchange Program .................................33
Before Contacting Daktronics ������������� 33
Repair & Return Program ........................34
Shipping Address ���������������������������������� 34
Daktronics Warranty and Limitation of
Liability ......................................................34
A Reference Drawings �������������������������35
B Daktronics Warranty and Limitation
of Liability�������������������������������������������37
This page intentionally left blank.
Introduction
1
1 Introduction
This manual provides the necessary information to install and service a Daktronics
Galaxy
®
eCCB (electronic changeable copy board) display.
Please read and understand all steps in this manual before beginning the installation
process.
For a smooth installation, complete the steps in this manual in order. Contact Daktronics
Technical Support with any questions before or during the installation process.
Limitation of Liability
The factory warranty will be nullied if:
The display is not installed according to the
steps in this manual
Proper electrical service is not provided or the
display is not grounded properly
Unauthorized modications are made to the
display, display cabinet, or the control system
Refer to Section B: Daktronics Warranty and Limitation of Liability (p�37) at the end of
this manual for the full Daktronics Warranty and Limitation of Liability.
Contact Information
For assistance before, during, or after display installation, please contact Daktronics
Technical Support: 800-DAKTRONICS (800-325-8766).
Model Number Guide
Daktronics Galaxy
®
eCCB model numbers are dened as follows:
ECCB-A100-XFTxXFT-M-R-F
ECCB
= Electronic changeable copy board
A100
= Product generation
X FT
= Feet high
X FT
= Feet long
M
= Pixel pitch in millimeters
R
= LED Color
F
= Face setup: SF – Single Face or 2V – Primary/Mirror
Figure 1 shows a label on the
display's back where the model
number and power requirements
are located.
Displays are either single face (SF)
or two view (2V). In 2V units, the rst
display is referred to as the primary
and the second is called the mirror.
GENERAL PURPOSE
RETROFIT SIGN
CONVERSION
FOR USE ONLY
IN ACCORDANCE WITH
KIT INSTRUCTIONS
KIT IS COMPLETE ONLY WHEN ALL PARTS
REQUIRED BY THE INSTRUCTIONS ARE PRESENT
CERTIFIED
SAFETY US-CA
E469414
Figure 1: Display Label
Introduction
2
Retrot Kit Parts
eCCB Display(s)
Interconnect cables
Installation Preparation
3
2 Installation Preparation
This section explains what to consider before installing a Daktronics Galaxy
®
eCCB
display.
Follow all guidelines and safety precautions in this manual when installing the display. Do
not modify the display or control system in any manner without the written permission of
Daktronics engineering staff.
Any unauthorized modications will nullify the display warranty.
Pre-Installation Checklist
Verify the following before starting installation:
The display was not damaged during shipping.
The mounting structure will provide a straight and square mounting frame for the
display.
The support structure can carry the weight of the display and meets local and
national codes.
Ensure proper power is available at sign structure – refer to shop drawing for display
power requirements.
All display modules are fully latched into the display cabinet.
Structure Requirements
Support structure design depends on mounting method, installation height, display size,
and weight. Because every installation site is unique, Daktronics approves no single
procedure for mounting displays.
Things to consider prior to installation:
Display structure and mounting must not obstruct airow - refer to shop drawing for
ventilation space requirements
Self-tapping screws must be used for mounting to structure
Light sensor must not be obstructed to maintain proper display dimming
For additional questions about display mounting requirements and specications, refer
to the display shop drawing or contact Daktronics Technical Support at 800-DAKTRONICS
(800-325-8766).
Display Installation
4
3 Display Installation
This section explains the steps necessary for proper lifting and installation of the display to
the sign structure.
Follow all guidelines and safety precautions in this manual when installing the display.
Do not modify the display or control system in any manner without the written permission
of Daktronics engineering staff. Any unauthorized modications will nullify the warranty.
Display Installation Preparation
Inspect the display for damage prior to installation
Provide an adequate support structure that is straight and level
Provide adequate ventilation that meets or exceeds display specications. See the
Shop Drawing for more information
Remove clip angles prior to lifting the display
Use all lift eyes when lifting the display
Do not drill holes into the display
Do not block display ventilation system
Do not use the lift eyes for display mounting
Display Installation
Only qualied individuals should install Galaxy
®
eCCB displays. The installer must ensure that the
mounting structure and hardware can support
the display, and that the structure follows all local
codes.
1� Evaluate the site where the Daktronics LED
display will replace the changeable copy
panel. The primary Daktronics display has
a radio antenna attached to its upper-left
corner.
2� Remove the left side perimeter retainers from
the existing changeable copy board display
structure.
3� Remove the changeable copy panel.
4� If necessary, reinforce internal anges. The customer must ensure that the structure
and the connectors are adequate.
5� Evaluate the changeable copy board's internal wiring. Route wiring in conduit from a
junction source to each face of the Galaxy
®
eCCB display.
6� Remove uorescent lights.
Note: Removing uorescent lights and ballasts is optional.
7� Uncrate the Galaxy
®
eCCB displays and remove the bag of screws attached to the
back of the display. Refer to Figure 2.
Figure 2: Uncrate Display
Display Installation
5
8� Using a boom or other lift equipment, position the Daktronics primary display beside
the sign structure. Lift the display from above
with the lift eyes.
9� Partially slide the Galaxy
®
eCCB display into
place within the remaining perimeter retainers
on the structure. Refer to Figure 3.
Note: Do not rest the display on the bottom
retainers.
10� Leave enough room between the Daktronics
display and the front of the changeable copy
board to make all electrical connections.
Note: In 2V display installations, when there
is no access to the signal cable, make
the connection through the access
panel on the mirror face.
11� Center and level the display, so the anges
are evenly spaced on all sides in the structure.
12� Insert a self-tapping screw through the display
ange, and the structure at each of the
etched locations on the Galaxy
®
eCCB display
anges. Refer to Figure 4. Screws are provided
and are located in the installation kit.
13� Re-install the perimeter retainers overlapping
the anges on the Galaxy
®
eCCB display.
Refer to Figure 5.
14� In the case of a 2V display; repeat steps 7
through 11 for the second face. Make the
signal connection between the primary and
mirror face using the already installed signal
cables before the second face is fully
mounted. Refer to Figure 6.
15� Repair and seal any unused openings in the
existing changeable copy board display
structure.
Note: Openings greater than
1
/
2
″ (12.7 mm)
in diameter require a metal patch
secured by screws or rivets and
caulked with non-hardening caulk.
Smaller openings may be sealed with
non-hardening caulk.
16� Start up the display and verify it is working
properly using a cellular phone or tablet
computer with Wi-Fi.
Figure 3: Slide eCCB Display into Place
Figure 4: Attachment Point with
Embossed Marking
Figure 5: Reattach Copy Board Retainers
Figure 6: Primary to Mirror Signal Cable
Connection
Electrical Installation
6
4 Electrical Installation
This section explains the steps necessary to make nal electrical connections to the
display from the primary power source. For display-specic power requirements, refer to
the shop drawing or label on the display's back.
Electrical Installation Preparation
Follow all installation guidelines
Route power to the display through a disconnect switch
Provide the required power per display requirements
Follow all local and national electrical codes
Do not wire the display to a timer or light sensor, ensuring the eCCB display has power
at all times
Do not connect the display to any voltage other than that listed on the product label
Do not connect the neutral to the ground at the disconnect or the display
Electrical Requirements
Do not connect displays to any voltage other than that listed on the display product
label. Galaxy
®
eCCB displays have a voltage input of 100-240 VAC and a frequency
input of 50/60 Hz. Galaxy
®
eCCB displays do not operate on 277 VAC. Connecting 277
VAC may damage internal components and will void the display's warranty.
A dedicated circuit can be shared among all components of the sign structure
(including Galaxy
®
eCCB displays and uorescent lighting), but only if the circuit is not
controlled by timers or external light sensors. If a circuit is controlled by these devices,
either assign the eCCB to a separate circuit so it has power at all times or disconnect the
timers or external light sensors.
The eCCB display cannot share a circuit with external electrical devices such as air
compressors or island lighting.
A dedicated circuit is dened as one hot, one neutral, and one ground wire.
Maximum amperage will vary with the number and size of Galaxy
®
eCCB displays
connected.
Follow all local and national electrical codes during electrical installation.
Note: Displays must be fed by a branch circuit no larger than 20A. Failure to meet wiring
and over-current protection device requirements may violate local and national
electrical codes and will void the display warranty.
Note: Size circuits according to local and national codes so the power distribution
system delivers full-load power to the display while maintaining a voltage within 5
percent of the nominal voltage.
Main Disconnect
Daktronics requires installation of a power disconnect switch with the display so all
ungrounded conductors can be disconnected near the point of power connection.
Electrical Installation
7
Electrical Installation
Only qualied individuals should perform power routing and termination to the display.
It is the electrical contractor's responsibility to ensure that all electrical work meets or
exceeds local and national codes. Improper installation could result in serious damage
to the equipment and could be hazardous to personnel.
Verify the existing disconnect switch (circuit breaker) has a rating that will handle the
Galaxy
®
eCCB display and the remaining sign load. If the rating of the branch circuit and
or disconnect switch is exceeded then a new disconnect switch and possibly additional
branch circuits may be required.
1� Disconnect power to the display.
2� Remove the bottom two modules from the second column on the left side of the
display with a
1
/
8
″ hex head wrench. A component layout is shown in Figure 7.
3� Locate the latch fastener on the module. It is centered in the third row of LEDs from
the top of the module. Refer to Figure 8. Turn the
wrench a quarter turn counter-clockwise.
4� Gently tip the top of the module outward slightly.
Then lift the module upward to disengage the tabs
at the bottom of the module from the slots on the
display's face sheet.
5� Disconnect the signal cables and unplug the power
cable by squeezing the tabs on the sides of the plug
head and pulling it out. Refer to Figure 9.
6� Remove the cover from the access panel on the
display's back sheet with a
1
/
4
″ nut driver.
7� Reach through the access hole and remove the
power termination junction box cover on the rear of
the display and remove.
8� Use a
3
/
16
″ nut driver to remove the term panel cover.
Light
Detector
Wi-Fi
Router
Controller
Thermostat
Power
Term
Panel
Power
Supply
Power
Supply
Fan
Fan
Fan
Fan
Fan
Figure 7: Component Layout - 3x8 Display
Figure 8: Remove Modules
Figure 9: Disconnect Cables
Electrical Installation
8
9� Locate the wiring inside of the junction box and pull all three wires out of the box, as
shown in Figure 10.
10� Remove the
1
/
2
conduit rubber plug
or plugs on the rear
the junction box, or
the exible
1
/
2
″ conduit
routed from the
electrical source can
be connected. Refer
to Figure 12.
11� Use wire nuts or other
appropriate hardware
to connect the wires
coming through the
conduit to the wires in
the junction box. Refer
to Figure 11.
12� Push all wires back into
the junction box and
reattach the gasket
and cover with
3
/
16
″ nut
driver.
13� Reconnect SATA
and power cables to
the module. Refer to
Figure 13.
14� Place modules back
into their proper
locations by inserting
the tabs at the bottom
of the modules in the
corresponding slots on
the display face sheet. Refer to Figure 14. Tip the top
of the module back into place and latch it by turning
the hex head wrench a quarter-turn clockwise.
Grounding
Galaxy
®
eCCB series displays do not require a local earth-
ground electrode.
The displays are designed so the most sensitive
components are isolated and an earth ground is not
required and is no longer recommended.
The displays still require a safety ground from the electrical
service panel for the primary power wires to comply with
national electric codes.
Please note that earth-grounding requirements for other
Daktronics products remain unchanged.
Figure 10: Pull Wires into Term
Panel
Figure 11: Connect Wires with
Wire Nuts
Figure 12: Attach Conduit Fitting
Figure 13: Reinstall Modules
Module
Tab
Figure 14: Tab on Back of
Module
System Start-Up Procedure
9
5 System Start-Up Procedure
Displays show a boot sequence about two minutes after power is turned on. Take note
of the IP Address shown during the boot sequence. The IP Address is used to log in to the
user interface that controls Galaxy
®
eCCB displays.
Boot Sequence
Description
Controller Name and Version
Display Size (Pixels High by Pixels Wide)
DHCP Name of Player
IP Address for User Interface
MAC Address
Conguration Port
Description
Start-Up Checklist
Conrm power is correctly connected to the display
Conrm there is sufcient power according to display requirements
Conrm a main disconnect is installed
Conrm that all communication equipment is installed according to provided
documentation
Inspect peripheral equipment (temperature sensor) for proper installation
Display Communication
10
6 Display Communication
This section explains how to establish communications with and log in to a Galaxy
®
eCCB
series display.
OS Requirements
Most popular smart devices and tablets can control Galaxy
®
eCCB displays.
Galaxy
®
eCCB displays support the following mobile browsers:
Apple Safari Firefox
Google Chrome Microsoft Internet Explorer version 10 or greater
Display Login
1� Get in range of the display - less than 400 feet.
2� Open device (smart phone or tablet).
3� Open Wi-Fi connections.
Note: The following images are representative. Each device may look differently
than what is shown.
4� Scan for Wi-Fi networks.
Display Communication
11
5� Select ECCB-xx-xxxx.
6� Enter the password, shown on the label attached to the installation quick guide.
Note: Credentials are also found on a label inside the display on the Wi-Fi router.
7� Tap Join or Connect.
8� Once connected to the display, open a browser window (Safari, Chrome, Internet
Explorer, Firefox).
Note: Blackberry is not supported
9� Type http://192�168�0�2 in the address bar. You will be redirected to the web page.
Note: The IP address is shown during the boot sequence.
Display Communication
12
10� Enter the following:
User Name
Dak
Password
DakPassword!
Add a shortcut to the eCCB user interface on the device's home screen. Consult the
device's manual for instructions.
Change Password
1� After logging in to
the Galaxy
®
eCCB
user interface, tap
the Gear icon at the
top-left corner of the
screen and select the
Change Password
button.
Display Communication
13
2� Enter the existing password. Enter and conrm a new password in the boxes
provided. When nished, tap Update Password.
Create Messages
1� Tap the Add New button.
2� Enter a Title for the message.
Display Communication
14
3� Select a Template. Text is shown in one, two, three, or four lines per frame depending
on the size of display.
4� Tap the Text Box and enter a message.
Note: Text does not scroll. What appears on screen is what appears on the display.
5� Add a frame to the message by tapping the + button.
Note: Each message can contain up to three frames.
6� Tap the Play hours button to set the time period in which the message is displayed.
Note: Leave the All Day toggle set to on if you want messages to run 24 hours daily.
Display Communication
15
7� Toggle the All Day setting to Off to select Start and End times. Tap Set after desired
Start and End times are selected.
8� Tap the Days of the week button to select which days the message appears on the
display.
9� Tap Save when nished.
Display Communication
16
10� Tap the Hold Time down-pointing arrow to change the hold time of each frame in a
message. Tap Done when nished.
Note: Hold times range from 1 second to 30 seconds.
11� Tap Save when nished with message creation.
Change Message Order
Change message order by dragging the three horizontal bars of a message on the right
side of the window to a new location.
Actively running messages have a green icon next to them.
Messages not currently running on the display, are shown with a red icon next to them.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41

Daktronics GALAXY ECCB Series Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI