FläktGroup ISYteq network User manual

Brand: FläktGroup

Model: ISYteq network

Type: User manual

ISYteq Network Configurator

USER MANUAL

ISYteq Network Configurator

2 FG 10549-ISYteq network configurator-GB 2021-01/R0 • Subject to change

ISYteq Network Configurator

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 3

1 General description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.1 Structure overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.2 Out of scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.3 Prerequisites . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4 Supported settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2 Network modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Setup new project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Main screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

2.3 About menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.4 General BMS settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.5 Single group overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.6 Single node screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.7 Upload AUTOPAR screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.8 Setup & installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3 Miscellaneous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

4 Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

4.1 Example for resulting IP and BACnet settings . . . . . . . . . . . . . . . . . 15

4.2 Parameter ranges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Disclosing, copying, distributing or taking any action in reliance on the contents of this document is strictly prohibited

without express prior consent. Violations entail liability for any damages or other liability arising. All rights in relation to

patents, utility patents or design patents are reserved.

General description ISYteq Network Configurator

4FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

1 General description

This manual is intended for service technicians. The manual focuses on the connection

commissioning tool to make the ISYteq network configuration secure and fast without

special hardware and knowledge. It also offers the possibility to prepare configurations

in advance and make them available to the service/customer. The configuration of a

single network can be saved in a single file, copied or sent by e-mail.

The output of this tool consists of a parameter file („AUTOPAR.TXT“). This file is copied

or saved directly to the controller via micro USB cable.

After removing the USB cable, the controller automatically loads the saved file and per-

forms an automatic restart to activate the network parameters (no need to disconnect

the power).

1.1 Structure overview

1.2 Out of scope

It is not possible to read back the active controller parameters.

– Single Unit access is mandatory

– Configuration via network

Other parameters than those described in this document cannot be processed. This

algorithm is restricted to a maximum number of variables, because it is executed

during runtime on the controller.

1.3 Prerequisites

The installed software on the ISYteq controller must have minimum application

version 2.1.0.0. and PC with Microsoft Windows® 10 and minimum .NET

Framework 4.5.

FG ISYteq Network Configurator

Save Project Load Project Single Group

Overview

General

BMS Settings About

Single Node Screen

Upload AUTOPAR

ISYteq Network Configurator General description

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 5

1.4 Supported settings

– ISYteq group network setup:

With BACnet MS/TP or IP up to 15 slaves per group, limited to a total number of 64

nodes for MS/TP.

– BMS interface setup:

With BACnet MS/TP or IP, Modbus RS485 or TCP and KNX. Selectable protocols

depending on the group network topology.

– IP-address and settings:

Optional ipv4 parameters like address, subnet, DNS, gateway or DHCP, can be set.

– HMI register:

CET, LCD-IW, or Touch 4.0 can be registered on master nodes.

Network modeling ISYteq Network Configurator

6FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

2 Network modeling

2.1 Setup new project

Select an applicable group network

MS/TPNone IP

For individual MAC settings dis-

miss MAC by max group size

(Menu: Advanced ►Enable)

Define number of groups,

size and descriptive names

Select and define basic/starting

IP-settings (ipv4), if necessary

Define base/starting

BACnet device ID

Select general BMS interface, via

sub mask, if necessary

Standalone

ISYteq Network Configurator Network modeling

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 7

2.2 Main screen

Fig. 1: Main start screen of ISYteq network configurator

In the main window the user can create the topology of the network, almost all settings

for a standard network will be calculated automatically to avoid mistakes during config-

uration.

This setting is representing the number of rooms (groups) that are connected to this

network.

This selection represents the number of units within the selected room.

2.2.1 Menu functions

•Language:

– EN – English (default)

– DE – Deutsch

– FR – Français

– NL – Nederlands

–CS – Čeština

•Load Project:

– Here the user can only load a project file which was created by the network con-

figurator (no other files).

– If the user loads a project file which was created with own settings for the ”MAC

by Max group size” he will see the full project file with the correspond settings,

but if the settings have to be changed the user must be in the “Enable” function

(see Menu functions - Advanced). Otherwise he will only see the settings.

Network modeling ISYteq Network Configurator

8FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

•Save Project:

– The current programmed display configuration can be saved here.

•Version:

– The installed ISYteq version can be selected. Depending on the version, the

configurator changes the topology and more or less functionalities can be con-

figured. Each ISYteq version has their own configurator interface.

– By saving a file with a wrong ISYteq version the programme gives a failure feed-

back and the user cannot save the configuration file. In this case the user must

adapt the ISYteq version on the main screen. If this is not possible, the installed

ISYteq version does not match the selected version in the tool or it is the previ-

ous version of 2.1.0.0. and does not support the automatic parameter upload.

•Advanced:

– Enable:

This function allows the user to dismiss the „MAC by Max group size“ setting (on-

ly for MS/TP network). In this case the „Start MAC“ can be defined. Hint: The op-

tion „MAC by max group size“ is known on the PGD1 (the tool used by our

service personnel when setting up this system in the past) as „automatic MAC“.

In addition, MaxMaster offset (placeholder) can be defined for a following BAC-

net MS/TP network on the same line.

Furthermore, the user gets the opportunity to dismiss the “IP by max group size”.

–Disable:

This option deactivates the selection field of „MAC by max. group size“ and „IP

by max. group size“ and causes the default or predefined network settings to be

applied.

•About:

– This menu includes the supplier information and license agreement.

ISYteq Network Configurator Network modeling

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 9

2.3 About menu

Fig. 2: License agreement for ISYteq network configurator

•Show version information and the License agreement.

(No translation of the license conditions is provided. The above English version is

always displayed.)

2.4 General BMS settings

Fig. 3: BMS settings with selectable parameters for installed units

Network modeling ISYteq Network Configurator

10 FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

•Select a BMS type:

– Types that are restricted by the group network are not selectable.

(E.g. group network BACnet MS/TP exclude BMS Modbus RS485).

•For BMS Modbus or KNX:

– The data points with write authorization can be selected from the list.

– The base station address for the first master node can be changed from default,

other master nodes in the network get an incremental address.

•BMS BACnet device ID for the first master node is defined on main screen (because

there is only one unique BACnet stack for group and/or BMS network).

2.5 Single group overview

Fig. 4: Selection of individual nodes

•The number of displayed nodes depends on the group size settings in the main

screen.

•An individual node can be selected for configuration by pressing the corresponding

button.

•A warning message is always shown:

– Opening the devices and connecting the USB cable is reserved for electrically

instructed persons or qualified electricians.

Electrocution through hazardous voltage will lead to death or serious injury!

•Disconnect the unit from the power supply and ensure the power cannot be

switched back on.

•Ensure the unit is voltage-free and isolated, earth and short circuit the unit, cover

or shield off neighbouring live components.

ISYteq Network Configurator Network modeling

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 11

2.6 Single node screen

Fig. 5: Node settings for master unit

•Overview of group and BMS network and interface settings that are already defined

at the main screen (here read only).

•The effective BACnet Device ID and/or Modbus address for this node is shown.

•If IP settings are selected, the parameters for this node are displayed here.

•If BACnet MS/TP is present, the RS485 bus parameters are shown.

•Definitive HMI settings (only in the case that this node is a master)

Slave nodes always get HMI selection “None” = invisible. All HMI settings that are

already present in the controller are reset during the configuration process.

•The effective BACnet Device ID and/or Modbus address for this node is displayed.

If no IP settings are selected on the main screen, the existing IP settings in the control-

ler is retained.

If the optional HMI is not selected, existing HMI settings in the controller are overwrit-

ten.

Network modeling ISYteq Network Configurator

12 FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

2.7 Upload AUTOPAR screen

Fig. 6: Saving settings in external file for subsequent upload

Pressing the Upload button opens a Windows file explorer. Here the USB drive of the

controller is selected as the target drive. There the suggested file is stored with the

save button. The „save“ button includes a version check function (see chapter 2.2.1

„Menu functions“).

If the controller version is an another than selected in the configurator, the program

gives a failure feedback (see picture below). To save the file correctly the user must

adapt the version in the configurator or the installed ISYteq version does not support

the automatic parameter upload function.

ISYteq Network Configurator Network modeling

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 13

2.8 Setup & installation

For setup and installation an installer is provided.

The installer „Setup_FG_ISYteq_NetworkConfigurator_1.0.exe“ require administrator

rights.

The starting installer screen shows the license agreement from chapter 2.3 „About

menu“. Require the administrator rights and follow the flow off the setup tool.

Fig. 7: Standard license agreement

Miscellaneous ISYteq Network Configurator

14 FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change

3 Miscellaneous

Installation requirements for this tool:

•Microsoft .NET Framework 4.5 or newer needed

•License agreement

Third Party Copyrights & Trademarks:

•Microsoft Corporation:

Microsoft®, Windows®

Microsoft .NET Framework

ISYteq Network Configurator Appendix

FläktGroup DC-2021-10549-GB 2021-01/R0 • Subject to change 15

4 Appendix

4.1 Example for resulting IP and BACnet settings

Tab. 1: Standard factory-made network settings

IP by max group size: IP-addresses are calculated with maximum given group size for

all groups.

Without IP by max group size: IP-addresses are calculated with individual given group

size.

The resulting group size (written to an individual node) is always set to the maximum

group size within this network. Otherwise duplicate BACnet device ID’s could occur.

This is not visible on the main screen, but on single node screen.

The same procedure is executed for IP by max group size.

4.2 Parameter ranges

•Base ID: 1- 4194303

•MAC ID: 1-127

•MaxMaster: 0-127

•Node No: 0-15

•Group No: 0-15

•KNX Address: 1-247

•Modbus Address: 1-247

Unit

1.1 1.2 1.3 1.4 1.4.1 1.5

Master / Slave MM M S M M

Start IP-Address 192.168.0.10 192.168.0.11 192.168.0.12 192.168.0.13 192.168.0.14 192.168.0.15

Start IP-Address +

IP by max group size

192.168.0.10 192.168.0.12 192.168.0.14 192.168.0.16 192.168.0.17 192.168.0.18

Start MAC 11 12 13 14 15 16

Max Master

(Calc from Start MAC)

18 18 18 18 18 18

Start BACnet Base ID 101 101 101 101 101 101

Group Size enter 1112 1

Group Size (calc) 222222

Group No 012334

Node No (Calc) 000010

BACnet Device ID

(Calc by ISYteq)1

101 103 105 107 108 109

MAC by Max group size

(Calc by ISYteq)2

135789

Max Master

(calc from MAC by Max

group size)

12 12 12 12 12 12

1) DeviceID = BaseID + GroupSize* GroupNo + NodeNo

2) MAC by Max group size = (DeviceID - BaseID + 1) modulo 127

ISYteq

WWW.FLAKTGROUP.COM

FläktGroup is the European market leader for smart and energy efficient Indoor Air

and Critical Air solutions to support every application area. We offer our customers

innovative technologies, high quality and outstanding performance supported by more

than a century of accumulated industry experience. The widest product range in the

market, and strong market presence in 65 countries worldwide, guarantee that we

are always by your side, ready to deliver Excellence in Solutions.

PRODUCT FUNCTIONS BY FLÄKTGROUP

Air Treatment | Air Movement | Air Diffusion | Air Distribution | Air Filtration

Air Management | Air Conditioning & Heating | Controls | Service

» Learn more on www.flaktgroup.com

or contact one of our office

FläktGroup ISYteq network User manual

FläktGroup ISYteq network User manual

FläktGroup ISYteq network User manual

Related papers

Other documents