WAGO Controller BACnet/IP User manual

Type
User manual
Pos: 2 /D o kum enta tion al lge mein/E in ban d/E inba nd Fro ntsei t e - H and buch ; CI 2 017; mit D oc Varia bl en (Stan dar d) @ 28 \mo d_1 486 4775 029 10_ 0.do cx @ 4053 88 @ @ 1
Manual
WAGO I/O System 750
750-832(/xxx-xxx)
Controller BACnet/IP; G4; 2ETH; SD
Controll
er BACnet/IP; Generation 4; 2 x ETHERNET;
SD Card Slot
1.0.2
Pos: 3 /A ll e Se rien (A ll ge meine Mo dule )/Rec htlic hes, Al lgem eines / Imp ress um f ür S t anda rdh and büch er - allg . A nga ben , Ansc h rifte n, T elefo nnu mm ern und E -Mai l-Adr essen @ 3\mo d_12 191 511 182 03_ 21.d oc x @ 210 60 @ @ 1
2 WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
© 2021 WAGO Kontakttechnik GmbH & Co. KG
All rights reserved.
WAGO Kontakttechnik GmbH & Co. KG
Hansastraße 27
D-32423 Minden
Phone: +49 (0) 571/8 87 – 0
Fax: +49 (0) 571/8 87 1 69
E-Mail: info@wago.com
Web: www.wago.com
Technical Support
Phone: +49 (0) 571/8 87 4 45 55
Fax: +49 (0) 571/8 87 – 84 45 55
E-Mail: support@wago.com
Every conceivable measure has been taken to ensure the accuracy and
completeness of this documentation. However, as errors can never be fully
excluded, we always appreciate any information or suggestions for improving the
documentation.
E-Mail: documentation@wago.com
We wish to point out that the software and hardware terms as well as the
trademarks of companies used and/or mentioned in the present manual are
generally protected by trademark or patent.
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.
=== E nde der Liste für Tex tma rke E in ban d_vo rne == =
WAGO I/O System 750 Table of Contents 3
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 5 /Do kum enta tion al lge mein/V e rzeic hnisse/ I nhal tsver z eichnis - Ü berschrift oG und Ve rzeic hnis @ 3\m od_ 121 915 1230 875 _21 .docx @ 21 063 @ @ 1
Table of Contents
1 Notes about this Documentation ........................................................... 10
1.1 Validity of this Documentation............................................................... 10
1.2 Copyright .............................................................................................. 10
1.3 Property rights ...................................................................................... 11
1.4 Symbols ............................................................................................... 12
1.5 Number Notation .................................................................................. 14
1.6 Font Conventions ................................................................................. 14
2 Important Notes ....................................................................................... 15
2.1 Legal Bases .......................................................................................... 15
2.1.1 Subject to Changes .......................................................................... 15
2.1.2 Personnel Qualifications................................................................... 15
2.1.3 Use of the 750 Series in Compliance with Underlying Provisions ..... 15
2.1.4 Technical Condition of Specified Devices ......................................... 16
2.1.4.1 Disposal ...................................................................................... 17
2.1.4.1.1 Electrical and Electronic Equipment ........................................ 17
2.1.4.1.2 Packaging ............................................................................... 18
2.2 Safety Advice (Precautions).................................................................. 19
2.3 Special Use Conditions for ETHERNET Devices .................................. 22
3 System Description ................................................................................. 23
3.1 Labeling ................................................................................................ 24
3.1.1 Labeling Symbols ............................................................................. 24
3.1.2 Manufacturing Number ..................................................................... 25
3.1.3 Hardware Address (MAC-ID) ........................................................... 26
3.1.4 Update Matrix ................................................................................... 27
3.2 Storage, Assembly and Transport ........................................................ 28
3.3 Assembly Guidelines/Standards ........................................................... 28
3.4 Power Supply ....................................................................................... 29
3.4.1 Overcurrent Protection ..................................................................... 29
3.4.2 Isolation ........................................................................................... 30
3.4.3 System Supply ................................................................................. 31
3.4.3.1 Connection .................................................................................. 31
3.4.3.2 Dimensioning............................................................................... 32
3.4.4 Field Supply ..................................................................................... 36
3.4.4.1 Connection .................................................................................. 36
3.4.4.2 Fusing via Power Supply Module ................................................. 38
3.4.4.3 Fusing external ............................................................................ 40
3.4.5 Supplementary Power Supply Regulations....................................... 42
3.4.6 Supply Example ............................................................................... 43
3.4.7 Power Supply Unit............................................................................ 45
3.5 Grounding............................................................................................. 46
3.5.1 Grounding the DIN Rail
.................................................................... 46
3.5.1.1 Framework Assembly .................................................................. 46
3.5.1.2 Insulated Assembly ..................................................................... 46
3.5.2 Grounding Function.......................................................................... 47
3.6 Shielding .............................................................................................. 48
3.6.1 General ............................................................................................ 48
4 Table of Contents WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
3.6.2 Fieldbus Cables ............................................................................... 48
3.6.3 Shielded Signal Lines ....................................................................... 49
3.6.4 WAGO Shield Connecting System ................................................... 49
4 Device Description .................................................................................. 50
4.1 View ..................................................................................................... 54
4.2 Connectors ........................................................................................... 56
4.2.1 Device Supply .................................................................................. 56
4.2.2 Fieldbus Connection ........................................................................ 56
4.3 Display Elements .................................................................................. 58
4.4 Operating Elements .............................................................................. 60
4.4.1 Service Interface .............................................................................. 60
4.4.2 Mode Selector Switch ...................................................................... 61
4.4.3 Address Selection Switch ................................................................. 63
4.4.4 Memory Card Slot ............................................................................ 64
4.4.4.1 Inserting a Memory Card ............................................................. 65
4.4.4.2 Removing the Memory Card ........................................................ 65
4.5 Technical Data ..................................................................................... 66
4.5.1 Device Data ..................................................................................... 66
4.5.2 System Data .................................................................................... 66
4.5.3 Supply .............................................................................................. 67
4.5.4 Fieldbus BACnet/IP .......................................................................... 67
4.5.5 Accessories...................................................................................... 68
4.5.6 Connection Type .............................................................................. 68
4.5.7 Climatic Environmental Conditions ................................................... 69
4.5.8 Mechanical Strength ........................................................................ 70
4.5.9 Software Compatibility ..................................................................... 70
4.6 Approvals ............................................................................................. 71
4.7 Standards and Guidelines .................................................................... 73
4.8 BACnet-Building-Controller (B-BC) ....................................................... 74
4.8.1 BIBBs (BACnet Interoperability Building Blocks) .............................. 75
4.8.2 Data Sharing BIBBs ......................................................................... 77
4.8.3 Alarm and Event Management BIBBs .............................................. 79
4.8.4 Scheduling BIBBs ............................................................................ 81
4.8.5 Trending BIBBs ................................................................................ 81
4.8.6 Device- und Network-Management-BIBBs ....................................... 83
4.8.7 „Native“ Operation of the B-BC......................................................... 86
5 Mounting .................................................................................................. 88
5.1 Installation Position ............................................................................... 88
5.2 Overall Configuration ............................................................................ 88
5.3
Mounting onto Carrier Rail .................................................................... 90
5.3.1 Carrier Rail Properties ...................................................................... 90
5.3.2 WAGO DIN Rails.............................................................................. 91
5.4 Spacing ................................................................................................ 91
5.5 Mounting Sequence .............................................................................. 92
5.6 Inserting and Removing Devices .......................................................... 93
5.6.1 Inserting the Fieldbus Coupler/Controller ......................................... 94
5.6.2 Removing the Fieldbus Coupler/Controller ....................................... 94
5.6.3 Inserting the I/O Module ................................................................... 95
5.6.4 Removing the I/O Module................................................................. 96
WAGO I/O System 750 Table of Contents 5
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
6 Connect Devices ..................................................................................... 97
6.1 Data Contacts/Local Bus ...................................................................... 97
6.2 Power Contacts/Field Supply ................................................................ 98
6.3 Connecting a Conductor to the CAGE CLAMP
®
................................... 99
7 Function Description ............................................................................ 100
7.1 Operating System ............................................................................... 100
7.1.1 Start-up .......................................................................................... 100
7.1.2 Application Program Cycle ............................................................. 100
7.2 Process Data Architecture .................................................................. 103
7.2.1 Basic Structure ............................................................................... 103
7.2.2 Example of an Input Process Image ............................................... 105
7.2.3 Example of an Output Data Process Image.................................... 106
7.2.4 Process Data MODBUS TCP ......................................................... 107
7.3 Data Exchange ................................................................................... 108
7.3.1 MODBUS Memory Areas ............................................................... 109
7.3.2 Addressing ..................................................................................... 112
7.3.2.1 Addressing of I/O Modules ........................................................ 112
7.3.2.2 Example of Addressing .............................................................. 113
7.3.2.3 IEC-61131-3 Address Areas ...................................................... 115
7.3.2.4 Absolute Addressing .................................................................. 115
7.3.3 Data Exchange between MODBUS/TCP Master and I/O Modules . 117
7.3.4 Data Exchange between PLC Function (CPU) and I/O Modules .... 118
7.3.5 Data Exchange between Master and PLC Function (CPU) ............ 119
7.3.5.1 Example of MODBUS/TCP Master and PLC Function (CPU) .... 119
7.3.6 Application Example ....................................................................... 121
7.4 Memory Card Function ....................................................................... 122
7.4.1 Backup Function (Storing device-internal Data and Settings) ......... 123
7.4.2 Restore Function (Loading device-internal Data and Settings) ....... 125
7.4.3 Distribute Data and Settings ........................................................... 127
7.4.4 Saving BACnet Trend Data ............................................................ 129
7.4.5 Inserting a Memory Card During Operation .................................... 131
7.4.6 Removing the Memory Card During Operation ............................... 132
7.4.7 Saving WAGO I/O-PRO project to Memory Card ........................... 133
7.4.8 FTP Network Access to the File System of the Memory Card ........ 136
7.4.9 Access to Web Pages in the File System of the Memory Card ....... 137
7.5 Compatibility Information when replacing a 750-831 ........................... 138
7.5.1 Firmware Chances ......................................................................... 138
7.5.1.1 Backup & Restore...................................................................... 138
7.5.1.2 Factory Settings Standard Protocols ......................................... 138
7.5.1.3 COV_Increment for Analog Input/Analog Output ....................... 138
7.5.1.4 Daylight_Saving_Status cannot be written ................................. 138
7.5.2 Codesys Chances ................................
.......................................... 139
7.5.2.1 WagoLibSSL.lib ......................................................................... 139
7.5.3 Online Change ............................................................................... 139
7.5.3.1 Current building libraries ............................................................ 139
8 Commissioning ..................................................................................... 140
8.1 Connecting Client PC and Fieldbus Nodes ......................................... 141
8.2 Determining the IP Address of the PC ................................................ 141
6 Table of Contents WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
8.3 Assigning the IP Address to the Fieldbus Node .................................. 141
8.3.1 Information about the Starting Behavior regarding BACnet and
WAGO I/O-PRO Program .............................................................. 142
8.3.2 Assigning IP Address via Address Selection Switch ....................... 144
8.3.3 Assigning IP Address via DHCP ..................................................... 145
8.3.3.1 Enable DHCP via "WAGO Ethernet Settings" (without existing IP
address)" ................................................................................... 147
8.3.3.2 Enable DHCP via WBM (with existing IP address)..................... 148
8.3.4 Assigning IP Address via “WAGO Ethernet Settings” ..................... 149
8.3.5 Assigning the IP Address with a PLC program ............................... 151
8.3.6 Assigning the IP Address via BootP ............................................... 152
8.3.6.1 Reasons for Failed IP Address Assignment ............................... 154
8.4 Apply IP address permanently (option “static“) ................................... 155
8.5 Testing the Function of the Fieldbus Node.......................................... 156
8.6 Preparing the Flash File System ......................................................... 157
8.7 Synchronizing the Clock Time ............................................................ 159
8.8 Restoring Factory Settings ................................................................. 161
9 Programming the PFC Using WAGO-I/O-PRO ..................................... 162
9.1 Configuring the Controller using the I/O Configurator ......................... 165
9.1.1 Configuration using the “io-config.xml” File..................................... 168
9.2 Automatically prepare SYM_XML file .................................................. 170
9.3 Create SYM_XML file manually .......................................................... 173
9.4 ETHERNET Libraries for WAGO-I/O-PRO .......................................... 174
9.5 Functional Restrictions and Limits ...................................................... 176
9.6 General Information about IEC Tasks ................................................. 179
9.6.1 IEC Task Sequence ....................................................................... 181
9.6.2 Overview of Most Important Task Priorities .................................... 181
9.7 System Events ................................................................................... 183
9.7.1 Enabling/Disabling System Events ................................................. 183
9.8 Transfer the IEC Program to the Fieldbus Controller .......................... 185
9.8.1 Transfer via Serial Service Port ...................................................... 187
9.8.2 Transfer via Fieldbus and ETHERNET ........................................... 191
10 Configuring via the Web-Based Management System (WBM) ........... 193
10.1 WBM User Groups ............................................................................. 193
10.2 Open WBM ......................................................................................... 194
10.3 WBM Pages ....................................................................................... 195
10.4 Information ......................................................................................... 196
10.5 Administration ..................................................................................... 197
10.6 Backup & Restore ............................................................................... 200
10.7 Clock .................................................................................................. 203
10.8 Miscellaneous ..................................................................................... 205
10.9 SD Card ............................................................................................. 206
10.10 Storage Media .................................................................................... 207
10.11 Up
date ................................................................................................ 207
10.12 Ethernet .............................................................................................. 208
10.13 Protocols ............................................................................................ 212
10.14 SNMP ................................................................................................. 213
10.14.1 SNMP v1/v2c ................................................................................. 214
10.14.2 SNMP V3 ....................................................................................... 215
WAGO I/O System 750 Table of Contents 7
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
10.15 SNTP .................................................................................................. 216
10.16 TCP/IP ................................................................................................ 216
10.17 BACnet ............................................................................................... 218
10.18 BACnet Information ............................................................................ 220
10.19 Modbus .............................................................................................. 222
10.20 Modbus Mapping ................................................................................ 224
10.21 I/O Data .............................................................................................. 227
10.22 PLC Application .................................................................................. 228
10.23 WebVisu ............................................................................................. 232
10.23.1 Generate WebVisu-HTML .............................................................. 232
10.23.2 Set WebVisu as Start Page ............................................................ 232
11 Diagnostics ............................................................................................ 234
11.1 LED Signaling ..................................................................................... 234
11.1.1 Evaluating Fieldbus Status ............................................................. 235
11.1.2 Evaluating Node Status I/O LED (Blink Code Table) ................... 236
11.1.2.1 USR LED ................................................................................... 247
11.1.3 Evaluating Memory Card Status ..................................................... 247
11.1.4 Evaluating Power Supply Status .................................................... 247
11.2 Fault Behavior .................................................................................... 248
11.2.1 Fieldbus Failure ............................................................................. 248
11.2.2 Local Bus Failure ........................................................................... 249
12 Fieldbus Communication...................................................................... 250
12.1 Implemented Protocols ....................................................................... 250
12.1.1 Communication Protocols .............................................................. 250
12.1.1.1 IP (Internet Protocol) ................................................................. 250
12.1.1.2 TCP (Transmission Control Protocol) ........................................ 255
12.1.1.3 UDP (User Datagram Protocol) ................................................. 255
12.1.2 Configuration and Diagnostics Protocols ........................................ 256
12.1.2.1 BootP (Bootstrap Protocol) ........................................................ 256
12.1.2.2 DHCP (Dynamic Host Configuration Protocol) ........................... 257
12.1.2.3 HTTP (Hypertext Transfer Protocol) .......................................... 259
12.1.2.4 DNS (Domain Name Systems) .................................................. 259
12.1.2.5 SNTP-Client (Simple Network Time Protocol) ............................ 260
12.1.2.6 FTP-Server (File Transfer Protocol) ........................................... 260
12.1.2.7 SNMP (Simple Network Management Protocol) ........................ 261
12.1.2.7.1 MIB II Description.................................................................. 261
12.1.2.7.2 Traps .................................................................................... 263
12.1.2.8 Syslog Client ............................................................................. 263
12.1.2.8.1 Syslog Messages .................................................................. 265
12.1.2.8.2 Configuration ........................................................................ 265
12.1.3 Application Protocols ................................................................
...... 266
12.2 BACnet/IP........................................................................................... 267
12.3 Modbus Functions .............................................................................. 268
12.3.1 General .......................................................................................... 268
12.3.2 Use of the MODBUS Functions ...................................................... 271
12.3.3 Description of the MODBUS Functions .......................................... 272
12.3.3.1 Function Code FC1 (Read Coils) ............................................... 273
12.3.3.2 Function Code FC2 (Read Discrete Inputs) ............................... 275
12.3.3.3 Function Code FC3 (Read Multiple Registers) ........................... 277
8 Table of Contents WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
12.3.3.4 Function Code FC4 (Read Input Registers) ............................... 278
12.3.3.5 Function Code FC5 (Write Coil) ................................................. 279
12.3.3.6 Function Code FC6 (Write Single Register) ............................... 280
12.3.3.7 Function Code FC11 (Get Comm Event Counter)...................... 281
12.3.3.8 Function Code FC15 (Write Multiple Coils) ................................ 282
12.3.3.9 Function Code FC16 (Write Multiple Registers) ......................... 284
12.3.3.10 Function Code FC22 (Mask Write Register) .............................. 285
12.3.3.11 Function Code FC23 (Read/Write Multiple Registers) ............... 286
12.3.4 MODBUS Register Mapping .......................................................... 288
12.3.5 Modbus
Registers .......................................................................... 291
12.3.5.1 Accessing Register Values ........................................................ 292
12.3.5.2 Modbus-Watchdog .................................................................... 292
12.3.5.3 Modbus
Watchdog Register ....................................................... 294
12.3.5.4 Diagnostic Registers .................................................................. 298
12.3.5.5 Configuration Registers ............................................................. 299
12.3.5.6 Constant Registers .................................................................... 301
12.3.5.7 Firmware Information Registers ................................................. 303
13 I/O Modules ............................................................................................ 308
13.1 Overview ............................................................................................ 308
13.2 Process Data Architecture for Modbus TCP ....................................... 309
14 Application Examples ........................................................................... 310
14.1 Test of Modbus protocol and fieldbus nodes ....................................... 310
14.2 Visualization and Control using SCADA Software ............................... 310
15 Use in Hazardous Environments.......................................................... 313
15.1 Marking Configuration Examples ........................................................ 314
15.1.1 Marking for Europe According to ATEX and IECEx ........................ 314
15.1.2 Marking for the United States of America (NEC) and Canada (CEC)318
15.2 Installation Regulations....................................................................... 321
15.2.1 Special Notes including Explosion Protection ................................. 321
15.2.2 Special Notes Regarding ANSI/ISA Ex ........................................... 323
16 Appendix................................................................................................ 324
16.1 MIB II Groups ..................................................................................... 324
16.1.1 System Group ................................................................................ 324
16.1.2 Interface Group .............................................................................. 325
16.1.3 IP Group ........................................................................................ 327
16.1.4 IpRoute Table Group ...................................................................... 328
16.1.5 ICMP Group ................................................................................... 329
16.1.6 TCP Group ..................................................................................... 330
16.1.7 UDP Group .................................................................................... 331
16.1.8 SNMP Group .................................................................................. 332
16.2 WAGO MIB Groups ............................................................................ 333
16.2.1 Company Group ............................................................................. 333
16.2.2 Product Group ................................................................................ 333
16.2.3 Versions Group .............................................................................. 334
16.2.4 Real-Time Clock Group .................................................................. 335
16.2.5 Ethernet Group .............................................................................. 336
16.2.6 Actual Error Group ......................................................................... 336
WAGO I/O System 750 Table of Contents 9
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
16.2.7 PLC Project Group ......................................................................... 337
16.2.8 Http Group ..................................................................................... 338
16.2.9 Ftp Group ....................................................................................... 338
16.2.10 Sntp Group..................................................................................... 339
16.2.11 Snmp Group................................................................................... 339
16.2.12 Snmp Trap String Group ................................................................ 341
16.2.13 Snmp User Trap String Group ........................................................ 342
16.2.14 Plc Connection Group .................................................................... 342
16.2.15 Modbus Group ............................................................................... 343
16.2.16 Process Image Group .................................................................... 344
16.2.17 Plc Data Group .............................................................................. 345
Glossary .......................................................................................................... 346
Literature List ................................................................................................. 364
List of Figures ................................................................................................ 365
List of Tables .................................................................................................. 367
=== E nde der Liste für Tex tma rke V e rzeic hnis_v orn e = ==
10 Notes about this Documentation WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 7 /A ll e Se rien (A ll ge meine Mo dule )/Übe rs ch rifte n/E ben e 1/Hi nweis e zu di eser D oku men tatio n - Ü bersc hri ft 1 @ 4\m od_ 123 798 7661 750 _21 .docx @ 2 9029 @ 1 @ 1
1 Notes about this Documentation
Pos: 8 /A ll e Se rien (A ll ge meine Mo dule )/S iche rheit s - und s o nstig e H inwei s e/Hi nweis / Hinw eis: D oku ment ation auf bew a hre n @ 4\mod_1 237 987 339 812 _21. docx @ 29 026 @ @ 1
Always retain this documentation!
This documentation is part of the product. Therefore, retain the documentation
during the entire service life of the product. Pass on the documentation to any
subsequent user. In addition, ensure that any supplement to this documentation
is included, if necessary.
Pos: 9 /A ll e Se rien (A ll ge meine Mo dule )/Übe rs ch rifte n/E ben e 2/ Gült igk eit sbe reic h - Ü bersc hri ft 2 @ 12\ mod _13 3891244 877 6_2 1.do c x @ 9 646 9 @ 2 @ 1
1.1 Validity of this Documentation
Pos: 10 /S erie 750 (W AGO I/ O SY STE M)/ Hinw eise zur D oku men tatio n (al t e Str uktu r)/G ül tigkei t sbe reic h/ Gülti gk eits be reic h Dok u ment atio n K op pler/C ont rol ler 75 0-xxxx, S tand ard versi on u nd a ufg elis tete Var. @ 14 \mod_1 358 944 040 291_ 21. docx @ 10 937 0 @ @ 1
This documentation is only applicable to the “Controller BACnet/IP; G4; 2ETH;
SD” (750-832) and the variants listed in the table below.
Pos: 11 /S erie 750 (W AGO I/ O SY STE M)/ Hinw eise zur D oku men tatio n (al t e Str uktu r)/G ül tigkei t sbe reic h/Va ri an tenlis t en/Va ri ant enliste - 7 50-832 , -8 32/0 00 -002 @ 3 5\m od_ 1560 256 569 006 _21. docx @ 54 742 1 @ @ 1
Table 1: Variants
Item number/Variant
Designation
750-832
Controller BACnet/IP; G4; 2xETH; SD
750-832/000-002
Controller BACnet/IP; G4; 2xETH; SD; ECO
(max. 256 application-based objects*)
* The application-based objects include all objects subject to manipulation by the user:
Native objects created automatically by connecting I/O modules
Dynamic objects created via BACnet services
Configured objects created via CODESYS or the BACnet Configurator
Pos: 12 /S erie 750 (W AGO I/ O SY STE M)/ Hinw eise zur D oku men tatio n (al t e Str uktu r)/H inw ei se/A ch tung : Hi nweis zur D oku ment ati o n Koppl er-/C ont rolle r 75 0-xxxx @ 4\mo d_1 2390 959 642 96_ 21.d oc x @ 301 18 @ @ 1
The product “Controller BACnet/IP; G4; 2ETH; SD” (750-832) shall only be
installed and operated according to the instructions in this manual and the
system description for the WAGO I/O System 750.
Consider power layout of the WAGO I/O System 750!
In addition to these operating instructions, you will also need the system
description for the WAGO I/O System 750, which can be downloaded at
www.wago.com. There, you can obtain important information including
information on electrical isolation, system power and supply specifications.
Pos: 13. 1 / All e Se ri en (All gem eine Mod ule) /Ü be rschri ften /E ben e 2/U rhe bersc hutz - Üb ersc hrif t 2 @ 2 3\m od_ 143 564 704 2188 _21 .docx @ 1 848 08 @ 2 @ 1
1.2 Copyright
Pos: 13. 2 / All e Se ri en (A ll gemei ne Mod ule) /Rec htlic hes, Al lg emei nes /U rhe bers chutz ausf ührli c h @ 4\mo d_1 235 565 145 234 _21. docx @ 27 691 @ @ 1
This Manual, including all figures and illustrations, is copyright-protected. Any
further use of this Manual by third parties that violate pertinent copyright
provisions is prohibited. Reproduction, translation, electronic and phototechnical
filing/archiving (e.g., photocopying) as well as any amendments require the
written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany.
Non-observance will involve the right to assert damage claims.
Pos: 13. 3 / Dok ume ntati on all gem ein/ Glie de rung sel e ment e/- --Sei t enwec hsel --- @ 3\mod_ 122 110 804 507 8_0. docx @ 21 810 @ @ 1
WAGO I/O System 750 Notes about this Documentation 11
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 13. 4 / All e Se ri en (All gem eine Mod ule) /R echtli c hes, A llg emei nes/Sc h utzr echt e @ 3 4\m od_ 155 799 677 6201 _21 .docx @ 5 449 19 @ 2 @ 1
1.3 Property rights
Third-party trademarks are used in this documentation. This section contains the
trademarks used. The “®” and “TM” symbols are omitted hereinafter.
Adobe
®
and Acrobat
®
are registered trademarks of Adobe Systems Inc.
AS-Interface
®
is a registered trademark of AS-International Association.
BACnet
®
is a registered trademark of American Society of Heating,
Refrigerating and Air Conditioning Engineers, Inc. (ASHRAE).
Bluetooth
®
is a registered trademark of the Bluetooth SIG, Inc.
CiA
®
and CANopen
®
are registered trademarks of CAN in AUTOMATION
International Users and Manufacturers Group e. V.
DALI is a registered trademark of Digital Illumination Interface Alliance
(DiiA).
EtherCAT
®
is a registered trademark and patented technology of Beckhoff
Automation GmbH.
EtherNet/IP™ is a registered trademark of Open DeviceNet Vendor
Association, Inc (ODVA).
EnOcean
®
is a registered trademark of EnOcean GmbH.
IO-Link is a registered trademark of PROFIBUS Nutzerorganisation e.V.
KNX
®
is a registered trademark of KNX Association cvba.
Linux
®
is a registered trademark of Linus Torvalds.
LON
®
is a registered trademark of Echelon Corporation.
Modbus
®
is a registered trademark of Schneider Electric, licensed to the
Modbus Organization, Inc.
PROFIBUS
®
is a registered trademark of Siemens AG.
PROFINET
®
is a registered trademark of Siemens AG.
QR Code is a registered trademark of DENSO WAVE INCORPORATED.
Subversion
®
is a registered trademark of Apache Software Foundation.
Windows
®
is a registered trademark of Microsoft Corporation.
Pos: 13. 5 / Dok ume ntati on all gem ein/ Glie de rung sel e ment e/- --Sei t enwec hsel --- @ 3\mod_ 122 110 804 507 8_0. docx @ 21 810 @ @ 1
12 Notes about this Documentation WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 13. 6 / All e Se ri en (All gem eine Mod ule) /Ü be rschri ften /E ben e 2/S y mbole - Üb erschri ft 2 @ 13\mod_ 135 106 804 240 8_2 1.doc x @ 1 052 70 @ 2 @ 1
1.4 Symbols
Pos: 13. 7. 1 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/G efah r/G efah r: _W arn ung v or Pe rso nens c häd en all gemei n_ - Erläuterung @ 13\m od_ 1343 309 450 020 _21. docx @ 10 102 9 @ @ 1
Personal Injury!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13. 7. 2 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/G efah r/G efah r: _W arn ung v or Pe rs o nensc häd en d urch elek t risch en S tr om_ - Erl äute run g @ 13\ mod_ 134 330 969 491 4_2 1.docx @ 1 010 30 @ @ 1
Personal Injury Caused by Electric Current!
Indicates a high-risk, imminently hazardous situation which, if not avoided, will
result in death or serious injury.
Pos: 13. 7. 3 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/Wa rnu ng/W a rnu ng: _War nun g vo r P ers onen schä den al lge mein _ - Erl äute run g @ 13\mod _134 330 987 704 1_2 1.doc x @ 1 010 35 @ @ 1
Personal Injury!
Indicates a moderate-risk, potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Pos: 13. 7. 4 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/V o rsicht/V o rsic ht: _Wa rnu ng vo r P er sone nsch äde n al lge mei n_ - Erl äut eru ng @ 13\ mod_13 433 100 287 62_ 21. d ocx @ 101 038 @ @ 1
Personal Injury!
Indicates a low-risk, potentially hazardous situation which, if not avoided, may
result in minor or moderate injury.
Pos: 13. 7. 5 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/A cht ung/A c htun g: _W arn ung v or S achsc h äde n allg emei n_ - Erläu ter ung @ 13 \mo d_1 343 3101346 23_ 21. doc x @ 101 041 @ @ 1
Damage to Property!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13. 7. 6 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/A cht ung/A c htun g: _W arn ung vor S achsch äde n du rc h elekt rosta t ische A uflad ung _ - Erl äute ru ng @ 13\ mod_13 4331 022 770 2_2 1. do cx @ 1 010 44 @ @ 1
Damage to Property Caused by Electrostatic Discharge (ESD)!
Indicates a potentially hazardous situation which, if not avoided, may result in
damage to property.
Pos: 13. 7. 7 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/Hi nw eis /Hinw eis : _W ichti ger Hinw eis al lge mein_ - Erl äut e rung @ 13\mod_ 134 331 032 690 6_21 . docx @ 1 010 47 @ @ 1
Important Note!
Indicates a potential malfunction which, if not avoided, however, will not result in
damage to property.
Pos: 13. 7. 8 /Al le S eri e n (All ge mein e M odul e)/S iche rh ei ts- und s onsti ge H inw ei se/I nfor mati on/ I nfor mati on: _W eite re I nfor mati on al l gem ein_ - Erl ä uter ung @ 1 3\m od_1343 310 439 814 _21. docx @ 10 105 1 @ @ 1
WAGO I/O System 750 Notes about this Documentation 13
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Additional Information:
Refers to additional information which is not an integral part of this
documentation (e.g., the Internet).
Pos: 13. 8 / Dok ume ntati on all gem ein/ Glie de rung sel e ment e/- --Sei t enwec hsel --- @ 3\ mod_ 122 110 804 507 8_0. docx @ 21 810 @ @ 1
14 Notes about this Documentation WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 13. 9 / All e Se ri en (All gem eine Mod ule) /Ü be rschri ften /E ben e 2/D ars tell ung der Za hlens yste me - Übe rschri ft 2 @ 23 \mod_1 435 6471 280 78_ 21. d ocx @ 184 811 @ 2 @ 1
1.5 Number Notation
Pos: 13. 10 / All e Se ri en (All ge mein e Mo dule )/Rec htlic hes , Al lgem eines /Zahl ens yst e me @ 3\mod_ 122 105 9454 015 _21 . docx @ 21 711 @ @ 1
Table 2: Number Notation
Example
Note
100
Normal notation
0x64
C notation
'100'
'0110.0100'
In quotation marks, nibble separated
with dots (.)
Pos: 13. 11 / All e Se ri en (All ge mein e Mo dule )/Ü b ersch rifte n/E be ne 2 /S chriftk onve ntion en - Überschrift 2 @ 23\m od_1 435 647 186 005 _21. docx @ 18 481 4 @ 2 @ 1
1.6 Font Conventions
Pos: 13. 12 / All e Se ri en (All ge mein e Mo dule )/R ec htli ches , A llgem ei nes /Sc hriftk onv entio nen @ 3\ mod _12 210 5952 143 7_2 1.do cx @ 2171 4 @ @ 1
Table 3: Font Conventions
Font Type
Indicates
italic
Names of paths and data files are marked in italic-type.
e.g.: C:\Program Files\WAGO Software
Menu
Menu items are marked in bold letters.
e.g.: Save
>
A greater-than sign between two names means the selection of a
menu item from a menu.
e.g.: File > New
Input
Designation of input or optional fields are marked in bold letters,
e.g.:
Start of measurement range
“Value”
Input or selective values are marked in inverted commas.
e.g.: Enter the value “4 mA” under Start of measurement range.
[Button]
Pushbuttons in dialog boxes are marked with bold letters in square
brackets.
e.g.: [Input]
[Key]
Keys are marked with bold letters in square brackets.
e.g.:
[F5]
Pos: 14 /D oku ment ation al lge mein /G lied eru ngsel eme nte/ -- -Sei tenw echsel -- - @ 3 \mo d_1 221 108 0450 78_ 0.d ocx @ 218 10 @ @ 1
WAGO I/O System 750 Important Notes 15
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 15 /A ll e Serie n (A ll ge mein e M odul e)/Üb ers c hrift en/E be ne 1/Wi chtig e E rlä uter ung en - Übe rs ch ri ft 1 @ 4 \mod _12 414 288 991 56_ 21.d oc x @ 321 70 @ 1 @ 1
2 Important Notes
Pos: 16. 1 / All e Se ri en (All gem eine Mod ule) /R echtli c hes, A llg emei nes/Wi c htige E rläut eru nge n - Ei nl eitun g @ 3 \mo d_1 221 059 818 031_ 21. doc x @ 21 717 @ @ 1
This section includes an overall summary of the most important safety
requirements and notes that are mentioned in each individual section. To protect
your health and prevent damage to devices as well, it is imperative to read and
carefully follow the safety guidelines.
Pos: 16. 2 / All e Se ri en (All gem eine Mod ule) /Ü be rschri ften /E ben e 2/R ec htlic h e Gr undl age n - Ü bersc hrif t 2 @ 3\m od_ 122 106 062 6343 _21 .docx @ 2 1726 @ 2 @ 1
2.1 Legal Bases
Pos: 16. 3 / All e Se ri en (All gem eine Mod ule) /R echtli c hes, A llg emei nes/Än der ungs v orbehal t - Ü bersc hrift 3 u nd I nhalt @ 3\ mod _12 210 600 364 84_ 21.d ocx @ 217 20 @ 3 @ 1
2.1.1 Subject to Changes
WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any
alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all
rights arising from the granting of patents or from the legal protection of utility
patents. Third-party products are always mentioned without any reference to
patent rights. Thus, the existence of such rights cannot be excluded.
Pos: 16. 4 / Seri e 75 0 (W AGO I /O SY STE M )/Wic hti ge E rl äute run gen (alt e S truk tur )/P ers onal quali fik ati on/P ers o nalq uali fikati on 7 50-xxxx - Ü ber schri f t 3 und I nhal t @ 3 \mod_1 224 061 2080 46_ 21. docx @ 240 63 @ 3 @ 1
2.1.2 Personnel Qualifications
All sequences implemented on WAGO I/O System 750 devices may only be
carried out by electrical specialists with sufficient knowledge in automation. The
specialists must be familiar with the current norms and guidelines for the devices
and automated environments.
All changes to the coupler or controller should always be carried out by qualified
personnel with sufficient skills in PLC programming.
Pos: 16. 5 / Seri e 75 0 (W AGO I /O SY STE M )/Wic hti ge E rl äute run gen (alt e S truk tur )/B esti mmu ngsg em äße V erwe ndu ng/Bes ti mm ungs gem äß e Verw end ung 750-xxxx - Überschrift 3 @ 32\mod_1 536 041 141 528 _21. docx @ 49 849 4 @ 3 @ 1
2.1.3 Use of the 750 Series in Compliance with Underlying
Provisions
Pos: 16. 6 / Seri e 75 0 (W AGO I /O SY STE M )/Wic hti ge E rl äute run gen (alt e S truk tur )/B esti mmu ngsg em äße V erwe ndu ng/Bes ti mm ungs gem äß e Verw end ung 750-xxxx für Gerä te - U L6 1010 - Ve rw eis auf P r oduk t-HB @ 32\m od_ 153 604 097 805 8_2 1.docx @ 4 984 89 @ @ 1
Fieldbus couplers, controllers and I/O modules of the modular
WAGO-I/O-SYSTEM 750 receive digital and analog signals from sensors and
transmit them to actuators or higher-level control systems. Using controllers, the
signals can also be (pre-) processed.
This product fulfills the requirements of protection type IP20 and is designed for
use in dry interior spaces. There is protection against finger injury and solid
impurities up to 12.5 mm diameter is assured; protection against water damage is
not ensured.
The product represents an open-type device. It may only be installed in
enclosures (tool-secured enclosures or operating rooms) which fulfil the listed
requirements specified in the safety instructions in chapter “Safety Advice
(Precautions)”. Use without additional protective measures in environments within
which dust, corrosive fumes, gases or ionized radiation can occur is considered
improper use.
16 Important Notes WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
The product is intended for installation in automation systems. It does not have
its own integrated separator. A suitable separator must therefore be created on
the plant side.
The operation of the product in residential areas without further measures is only
permitted if the product complies with the emission limits (interference emissions)
according to EN 61000-6-3.
Operating the product in home applications without further measures is only
permitted if it meets the emission limits (emissions of interference) according to
EN 61000-6-3. Please observe the installation regulations!
You will find the relevant information in the section “Device Description” >
“Standards and Guidelines” in the manual for the used product.
Appropriate housing (per 2014/34/EU) is required when operating the
WAGO-I/O-SYSTEM 750 in hazardous environments. Please note that a
prototype test certificate must be obtained that confirms the correct installation of
the system in a housing or switch cabinet.
The implementation of safety functions such as EMERGENCY STOP or safety
door monitoring must only be performed by the F I/O modules within the modular
WAGO-I/O-SYSTEM 750. Only these safe F I/O modules ensure functional
safety in accordance with the latest international standards. WAGO's
interference-free output modules can be controlled by the safety function.
Pos: 16. 7 / All e Se ri en (All gem eine Mod ule) /R echtli c hes, A llg emei nes/ Technisc her Zust and der Geräte - Üb ersch rift 3 un d In hal t @ 3\ mod_ 122 106 044 610 9_2 1.docx @ 2 172 3 @ 3 @ 1
2.1.4 Technical Condition of Specified Devices
The devices to be supplied ex works are equipped with hardware and software
configurations, which meet the individual application requirements. These
modules contain no parts that can be serviced or repaired by the user. The
following actions will result in the exclusion of liability on the part of WAGO
Kontakttechnik GmbH & Co. KG:
Repairs,
Changes to the hardware or software that are not described in the
operating instructions,
Improper use of the components.
Further details are given in the contractual agreements. Please send your
request for modified and new hardware or software configurations directly to
WAGO Kontakttechnik GmbH & Co. KG.
Pos: 16. 8 / All e Se ri en (All gem eine Mod ule) /Ü be rschri ften /E ben e 4/E nt sor gen - Überschrift 4 @ 30\m od_ 151 0145 115 652 _21. docx @ 46 985 9 @ 4 @ 1
WAGO I/O System 750 Important Notes 17
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
2.1.4.1 Disposal
Pos: 16. 9. 1 /Al le S eri e n (All ge mein e M odule)/Ü bersc hriften/ Ebene 5/E lektro- u nd El ek tro nik ge räte - Übers chrift 5 @ 32\mod_ 153 744 698 806 8_2 1.doc x @ 5 016 57 @ 5 @ 1
2.1.4.1.1 Electrical and Electronic Equipment
Pos: 16. 9. 2 /Al le S eri e n (All ge mein e M odul e)/R ec htli ch es, A llge mei n es/E lektr o- und Elek tro nikge te @ 32\m od_ 153 2425 086 061 _21. docx @ 49 198 9 @ @ 1
Electrical and electronic equipment may not be disposed of
with household waste. This also applies to products without
this symbol.
Electrical and electronic equipment contain materials and substances that can be
harmful to the environment and health. Electrical and electronic equipment must
be disposed of properly after use.
WEEE 2012/19/EU applies throughout Europe. Directives and laws may vary
nationally.
Environmentally friendly disposal benefits health and protects
the environment from harmful substances in electrical and
electronic equipment.
Observe national and local regulations for the disposal of electrical and
electronic equipment.
Clear any data stored on the electrical and electronic equipment.
Remove any added battery or memory card in the electrical and
electronic equipment.
Have the electrical and electronic equipment sent to your local
collection point.
Improper disposal of electrical and electronic equipment can be harmful to the
environment and human health.
Pos: 16. 9. 3 /D oku ment ati on allge mei n /Glied eru ngs el eme nte/ --- -L eerz eil e-(1Z )- --- @ 28\mo d_1 485 262 995 837 _0.d ocx @ 404 006 @ @ 1
Pos: 16. 9. 4 /Al le S eri e n (All ge mein e M odul e)/Ü b ersc hrift en/ Ebe ne 5/V erp acku ng - Übe rsch rif t 5 @ 32 \mo d_1 537 447 0442 02_ 21. docx @ 501 662 @ 5 @ 1
18 Important Notes WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
2.1.4.1.2 Packaging
Pos: 16. 9. 5 /Al le S eri e n (All ge mein e M odul e)/R ec htli ch es, A llge mei n es/V erpac ku ng @ 32\ mod _15 374 467 864 16_ 21.d ocx @ 501 653 @ @ 1
Packaging contains materials that can be reused.
PPWD 94/62/EU and 2004/12/EU packaging guidelines apply throughout
Europe. Directives and laws may vary nationally.
Environmentally friendly disposal of the packaging protects the environment and
allows sustainable and efficient use of resources.
Observe national and local regulations for the disposal of packaging.
Dispose of packaging of all types that allows a high level of recovery,
reuse and recycling.
Improper disposal of packaging can be harmful to the environment and wastes
valuable resources.
Pos: 16. 10 / D okum ent ati on allge mein/ Gliede run gsel e me nte/ ---Sei tenwe chs el --- @ 3\mod _12 211 080 450 78_ 0.docx @ 2 181 0 @ @ 1
WAGO I/O System 750 Important Notes 19
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Pos: 16. 11 / All e Se ri en (All ge mein e Mo dule )/Ü b ersch rifte n/E be ne 2 /S icher heit shi nwei se - Übersc hrift 2 @ 6\mod_1 260 180 299 987 _21. docx @ 46 724 @ 2 @ 1
2.2 Safety Advice (Precautions)
Pos: 16. 12 / All e Se ri en (All ge mein e Mo dule )/S iche rhei t s- und s onstig e H inwei s e/E inlei t ung Si ch erh eitshi nweis e H ardw are @ 6\ mo d_12 601 801 704 93_ 21.d ocx @ 467 20 @ @ 1
For installing and operating purposes of the relevant device to your system the
following safety precautions shall be observed:
Pos: 16. 13. 1 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/ Gefa hr/ Gefa hr: N ic ht a n G e räte n u nter Span nun g ar beit en! @ 6\mod_ 126 018 036 532 7_21 . docx @ 4 672 7 @ @ 1
Do not work on devices while energized!
All power sources to the device shall be switched off prior to performing any
installation, repair or maintenance work.
Pos: 16. 13. 2 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/ Gefa hr/ Gefa hr: P r odu kt nu r in ei ne m g eeign ete n Ge häus e ei n bau en! @ 33\ mod _15 435 818 814 35_ 21.d ocx @ 511 972 @ @ 1
Install device in only one suitable enclosure!
The device is an open system. Install the device in a suitable enclosure. This
enclosure must:
Guarantee that the max. permissible degree of pollution is not exceeded.
Offer adequate protection against contact.
Prevent fire from spreading outside of the enclosure.
Offer adequate protection against UV irradiation.
Guarantee mechanical stability
Restrict access to authorized personnel and may only be opened with tools
Pos: 16. 13. 3 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/ Gefa hr/ Gefa hr: Tr ennv orric htun g u nd Üb erst ro msc hut z @ 3 3\m od_ 154 391 5978 439 _21 .docx @ 5 1226 7 @ @ 1
Ensure disconnect and overcurrent protection!
The device is intended for installation in automation technology systems.
Disconnect protection is not integrated. Connected systems must be protected by
a fuse.
Provide suitable disconnect and overcurrent protection on the system side!
Pos: 16. 13. 4 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/ Gefa hr/ Gefa hr: U nfall ve rhü tung svors c hrift en beac hten ! @ 6 \mod_1 260 180 6570 00_ 21. doc x @ 46 735 @ @ 1
Pos: 16. 13. 5 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/ Gefa hr/ Gefa hr: A u f no rm ger echte n A nschl us s ac hte n! @ 6\m od_1 260 180 753 479 _21. doc x @ 46 739 @ @ 1
Ensure a standard connection!
To minimize any hazardous situations resulting in personal injury or to avoid
failures in your system, the data and power supply lines shall be installed
according to standards, with careful attention given to ensuring the correct
terminal assignment. Always adhere to the EMC directives applicable to your
application.
Pos: 16. 14 / Se rie 7 50 (W AGO I / O SY STE M)/Wic htige E rläut eru nge n ( alte S tr uktu r)/S ich erh eits - und sons ti ge H inw ei se/Wa rnu ng/W arn ung: S pei su ng a ussc hlie ßli ch aus S ELV -/PELV-V erso rgu ng (K opple r/Co ntr ol ler) @ 3 7\m od_ 160 0424 785 073 _21. docx @ 59 378 9 @ @ 1
20 Important Notes WAGO I/O System 750
750-832 Controller BACnet/IP; G4; 2ETH; SD
Manual
1.0.2
Power from SELV/PELV power supply only!
All field signals and field supplies connected to this fieldbus coupler/controller
(750-832) must be powered from SELV/PELV power supply(s)!
Pos: 16. 15 / All e Se ri en (All ge mein e Mo dule )/S iche rhei t s- und s onstig e H inwei s e/V orsic ht/V o rsic ht: H ei ße Ob erfl äc he nic ht ber ühren! (allge mein ) @ 6\m od_ 126 4428 115 588 _21. doc x @ 48 610 @ @ 1
Do not touch hot surfaces!
The surface of the housing can become hot during operation. If the device was
operated at high ambient temperatures, allow it to cool off before touching it.
Pos: 16. 16 / All e Se ri en (All ge mein e Mo dule )/S iche rhei t s- und s onstig e H inwei s e/A cht ung/A c htun g: Ni cht in Telek o mmuni ka tions netze n ein s etze n! ( Zus atz R J -45 ) @ 3 \mo d_1 224 065 1874 68_ 21. docx @ 24 076 @ @ 1
Do not use in telecommunication circuits!
Only use devices equipped with ETHERNET or RJ-45 connectors in LANs.
Never connect these devices with telecommunication networks.
Pos: 16. 17. 1 /Serie 75 0 (W AGO I/O SY S TEM )/Wi chtig e E rlä ute rung en (alte S trukt ur )/S icher hei ts - und s o nstige H inwei s e/A chtu ng/A cht ung : E inwan dfr ei e Kon takt ie run g zu r T rags chien e gew äh rleist e n! @ 34\ mod_ 155048 140 763 8_2 1.doc x @ 5 305 99 @ @ 1
Ensure proper contact with the DIN-rail!
Proper electrical contact between the DIN-rail and device is necessary to
maintain the EMC characteristics and function of the device.
Pos: 16. 17. 2 /Al le Seri en (All g emei ne Mod ule)/S ich er heits- und sons ti ge Hi nw eise/ Ac htun g/ Achtu ng: D efekt e o der besc hädig te G erät e a ust au sche n! @ 6\m od_1 260 180 857 358 _21. docx @ 46 743 @ @ 1
Replace defective or damaged devices!
Replace defective or damaged device/module (e.g., in the event of deformed
contacts).
Pos: 16. 17. 3 /Al le Seri en (All g emei ne Mod ule)/S ich er hei ts- und s ons tige H i nwei se/A c htun g/A chtu ng: Ger äte v or k ri ech end en u nd is ol iere nde n S toff en sc hütz en! @ 6\ mod_ 126 018 103 621 6_2 1.doc x @ 4 674 7 @ @ 1
Protect the components against materials having seeping and insulating
properties!
The components are not resistant to materials having seeping and insulating
properties such as: aerosols, silicones and triglycerides (found in some hand
creams). If you cannot exclude that such materials will appear in the component
environment, then install the components in an enclosure being resistant to the
above-mentioned materials. Clean tools and materials are imperative for
handling devices/modules.
Pos: 16. 17. 4 /Al le Seri en (All g emei ne Mod ule)/S ich er heits- und sons ti ge Hi nw eise/ Ac htun g/ Achtu ng: R eini g ung nur mi t z uläs sig en Mate rial ien ! @ 6 \mo d_1 260 181 203 293_ 21. docx @ 46 751 @ @ 1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192
  • Page 193 193
  • Page 194 194
  • Page 195 195
  • Page 196 196
  • Page 197 197
  • Page 198 198
  • Page 199 199
  • Page 200 200
  • Page 201 201
  • Page 202 202
  • Page 203 203
  • Page 204 204
  • Page 205 205
  • Page 206 206
  • Page 207 207
  • Page 208 208
  • Page 209 209
  • Page 210 210
  • Page 211 211
  • Page 212 212
  • Page 213 213
  • Page 214 214
  • Page 215 215
  • Page 216 216
  • Page 217 217
  • Page 218 218
  • Page 219 219
  • Page 220 220
  • Page 221 221
  • Page 222 222
  • Page 223 223
  • Page 224 224
  • Page 225 225
  • Page 226 226
  • Page 227 227
  • Page 228 228
  • Page 229 229
  • Page 230 230
  • Page 231 231
  • Page 232 232
  • Page 233 233
  • Page 234 234
  • Page 235 235
  • Page 236 236
  • Page 237 237
  • Page 238 238
  • Page 239 239
  • Page 240 240
  • Page 241 241
  • Page 242 242
  • Page 243 243
  • Page 244 244
  • Page 245 245
  • Page 246 246
  • Page 247 247
  • Page 248 248
  • Page 249 249
  • Page 250 250
  • Page 251 251
  • Page 252 252
  • Page 253 253
  • Page 254 254
  • Page 255 255
  • Page 256 256
  • Page 257 257
  • Page 258 258
  • Page 259 259
  • Page 260 260
  • Page 261 261
  • Page 262 262
  • Page 263 263
  • Page 264 264
  • Page 265 265
  • Page 266 266
  • Page 267 267
  • Page 268 268
  • Page 269 269
  • Page 270 270
  • Page 271 271
  • Page 272 272
  • Page 273 273
  • Page 274 274
  • Page 275 275
  • Page 276 276
  • Page 277 277
  • Page 278 278
  • Page 279 279
  • Page 280 280
  • Page 281 281
  • Page 282 282
  • Page 283 283
  • Page 284 284
  • Page 285 285
  • Page 286 286
  • Page 287 287
  • Page 288 288
  • Page 289 289
  • Page 290 290
  • Page 291 291
  • Page 292 292
  • Page 293 293
  • Page 294 294
  • Page 295 295
  • Page 296 296
  • Page 297 297
  • Page 298 298
  • Page 299 299
  • Page 300 300
  • Page 301 301
  • Page 302 302
  • Page 303 303
  • Page 304 304
  • Page 305 305
  • Page 306 306
  • Page 307 307
  • Page 308 308
  • Page 309 309
  • Page 310 310
  • Page 311 311
  • Page 312 312
  • Page 313 313
  • Page 314 314
  • Page 315 315
  • Page 316 316
  • Page 317 317
  • Page 318 318
  • Page 319 319
  • Page 320 320
  • Page 321 321
  • Page 322 322
  • Page 323 323
  • Page 324 324
  • Page 325 325
  • Page 326 326
  • Page 327 327
  • Page 328 328
  • Page 329 329
  • Page 330 330
  • Page 331 331
  • Page 332 332
  • Page 333 333
  • Page 334 334
  • Page 335 335
  • Page 336 336
  • Page 337 337
  • Page 338 338
  • Page 339 339
  • Page 340 340
  • Page 341 341
  • Page 342 342
  • Page 343 343
  • Page 344 344
  • Page 345 345
  • Page 346 346
  • Page 347 347
  • Page 348 348
  • Page 349 349
  • Page 350 350
  • Page 351 351
  • Page 352 352
  • Page 353 353
  • Page 354 354
  • Page 355 355
  • Page 356 356
  • Page 357 357
  • Page 358 358
  • Page 359 359
  • Page 360 360
  • Page 361 361
  • Page 362 362
  • Page 363 363
  • Page 364 364
  • Page 365 365
  • Page 366 366
  • Page 367 367
  • Page 368 368
  • Page 369 369
  • Page 370 370
  • Page 371 371
  • Page 372 372
  • Page 373 373
  • Page 374 374

WAGO Controller BACnet/IP User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI