WAGO BACnet Configurator User manual

Product manual | Version 2.1.0, valid from SW Version 1.14.0

WAGO Software

WAGO BACnet Configurator

759-321

759-321Legal Information

WAGO Kontakttechnik GmbH & Co. KG

Hansastraße 27

D - 32423 Minden

Phone: +49 571/887 – 0

Fax: +49 571/887 – 844169

E-Mail: * [email protected]

Internet: ü www.wago.com

Technical Support

Phone: +49 571/887 – 44555

Fax: +49 571/887 – 844555

E-Mail: * [email protected]

Every conceivable measure has been taken to ensure the accuracy and completeness of

this documentation. However, as errors can never be fully excluded, we always appreci-

ate any information or suggestions for improving the documentation.

E-Mail: * [email protected]

We wish to point out that the software and hardware terms as well as the trademarks of

companies used and/or mentioned in the present manual are generally protected by

trademark or patent.

WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.

Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

759-321 Table of Contents

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 iii

WAGO BACnet Configurator

Table of Contents

1 Terms ................................................................................................................................6

1.1 Intended Use........................................................................................................... 7

1.2 Typographical Conventions..................................................................................... 8

1.3 Legal Information .................................................................................................... 9

2 Security...........................................................................................................................11

2.1 General Safety Regulations .................................................................................. 11

2.2 Indirect Safety ....................................................................................................... 11

3 Requirements .................................................................................................................12

3.1 System Requirements........................................................................................... 12

4 Overview .........................................................................................................................13

5 Installing .........................................................................................................................14

5.1 Installing the WAGO BACnet Controller................................................................ 15

5.2 Network Settings for BACstac............................................................................... 19

5.2.1 Check Active Firewall ...................................................................................19

5.2.2 Check Network Card IP Address..................................................................20

5.2.3 Checking BACstac .......................................................................................21

5.3 Information about the “BACnet Object Merger”..................................................... 22

5.4 Uninstalling the BACnet Controller........................................................................ 22

6 Starting............................................................................................................................23

7 Graphical User Interface ...............................................................................................24

7.1 Menu Bar............................................................................................................... 24

7.1.1 File................................................................................................................24

7.1.2 Edit ...............................................................................................................25

7.1.3 View..............................................................................................................25

7.1.4 Pool ..............................................................................................................26

7.1.5 Device ..........................................................................................................30

7.1.6 Extras ...........................................................................................................36

7.1.7 Help ..............................................................................................................37

7.2 Toolbar .................................................................................................................. 37

7.3 Views..................................................................................................................... 38

7.3.1 Device Pools ................................................................................................39

7.3.2 “Structured View”..........................................................................................41

7.4 Configuration Area ................................................................................................ 43

7.4.1 Pool ..............................................................................................................43

7.4.2 Device ..........................................................................................................45

7.4.2.1 Configuration of Device .......................................................................47

7.4.2.2 Configuration of “BBMD” .....................................................................53

7.4.2.3 Configuration of Communication .........................................................55

7.4.2.4 Configuring “IEC Variables” for 750-83x Controller .............................56

7.4.2.5 Configuring “IEC Variables” for PFC BACnet Devices ........................58

759-321Table of Contents

iv Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

7.4.2.5.1 WAGOBACnetConfigurator Version 1.14.0 or Higher ............. 58

7.4.2.5.2 BACnet Configurator Version 1.13 / e!COCKPIT Version 1.7.0

and Higher ................................................................................. 59

7.4.2.5.3 Up to BACnet Version 1.12........................................................ 68

7.4.2.6 Node-Configurator ...............................................................................77

7.4.2.7 Storing and Downloading a Valid Configuration ..................................78

7.4.3 Objekt ...........................................................................................................80

7.4.4 Object Specific Dialog ..................................................................................85

7.4.4.1 “Configure Object Structured View” Dialog..........................................85

7.5 Device Manager .................................................................................................... 87

7.5.1 Object Manager............................................................................................88

7.5.2 Client Mapping .............................................................................................90

7.5.3 Internal Mapping (IEC Mapping) ..................................................................94

7.5.4 Multi-Controller Projects ...............................................................................95

7.5.5 Multistate ......................................................................................................96

7.6 Online and Offline Status .................................................................................... 101

8 Function........................................................................................................................102

8.1 BACnet Objects................................................................................................... 102

8.1.1 Properties of BACnet..................................................................................104

8.1.2 BACnet Instance Numbers.........................................................................105

8.2 BACnet Services ................................................................................................. 106

8.3 Configuration Files .............................................................................................. 107

8.4 EDE Files ............................................................................................................ 108

8.5 “terminal.csv” File................................................................................................ 108

8.6 Persistent and Configured Values....................................................................... 109

8.7 Change Firmware or Controller........................................................................... 110

9 Example Configuration................................................................................................111

9.1 Configuring New Devices (Offline) ...................................................................... 111

9.2 Configuring New Devices (Online) ...................................................................... 111

9.3 Changing Property Values with BACnet ............................................................. 113

9.4 “Present Value” – Value Scaling in DeviceType ................................................. 115

9.5 Use EDE File Import............................................................................................ 116

9.5.1 EDE File Structure......................................................................................116

9.5.1.1 Header...............................................................................................116

9.5.1.2 Optional Properties............................................................................118

9.5.2 Export Process ...........................................................................................119

9.5.3 Import Process ...........................................................................................119

9.5.3.1 Hardware Instance Number...............................................................121

9.5.4 Creating and Importing an EDE File...........................................................122

9.6 Backing up and Restoring Files .......................................................................... 126

9.7 Working with Persistent and Configured Values ................................................. 128

9.8 Creating a “Client Mapping” ................................................................................ 130

9.9 Creating an “Internal Mapping” ........................................................................... 133

9.10 Configuring Objects............................................................................................. 136

759-321 Table of Contents

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 v

WAGO BACnet Configurator

9.10.1 Creating a Switching Schedule Program (“Schedule” objects) ..................137

9.10.2 Using Intrinsic Reporting (“Notification Class” objects) ..............................141

9.10.3 Creating Trend Recordings (“Trendlog” objects)........................................145

10 Mass Data Handling.....................................................................................................147

10.1 Configure Mode................................................................................................... 147

10.2 Device Manager .................................................................................................. 148

10.3 Client and Internal Mapping ................................................................................ 150

11 Appendix.......................................................................................................................151

11.1 List of BACnet Engineering Units........................................................................ 151

11.2 Compatibility with Configurator and Firmware Version ....................................... 155

11.3 Protected Rights.................................................................................................. 156

11.3.1 Copyright Protection of BACnet Standard (ASHRAE)................................156

759-321Terms

6 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

1Terms

This documentation applies to the WAGO BACnet Configurator in conjunction with the

following devices:

Devices with Pre-Installed Licenses

Table1: Scope of Applicability of the Documentation – Devices with Pre-Installed License

Device As of firmware version

BACnet/IP Fieldbus Coupler

750-330 29.02.01 (09)

BACnet/IP Fieldbus Coupler; 4th generation

750-332 20.01.01 (02)

BACnet MS/TP Controller

750-829 30.02.01 (09)

BACnet/IP Controller

750-830 12.03.04 (04)

750-831 29.02.01 (09)

750-831/000-002 29.02.01 (09)

750-832 20.01.01 (02)

750-832/000-002 20.01.01 (02)

PFC

750-8212/000-100 07.01.03 (13)

Devices without Pre-Installed License

Some devices need a license to be used with the WAGO BACnet Configurator:

Table2: Scope of Applicability of the Documentation – Devices without Pre-Installed License

Device

1

As of firmware version

PFC

750-8210 03.05.03 (17)

750-8210/0040-0000 03.05.03 (17)

750-8211 03.05.03 (17)

750-8211/0040-0000 03.05.03 (17)

750-8212 09.04.03 (16)

750-8212/0025-0000 09.04.03 (16)

750-8212/0025-0001 09.04.03 (16)

750-8212/0025-0002 09.04.03 (16)

750-8213 09.04.03 (16)

750-8216 03.05.03 (17)

750-8217 03.05.03 (17)

Touch Panel 600 Standard Line

0762-4301/8000-0002 09.04.03 (16)

0762-4302/8000-0002 09.04.03 (16)

0762-4303/8000-0002 09.04.03 (16)

0762-4304/8000-0002 09.04.03 (16)

0762-4305/8000-0002 09.04.03 (16)

0762-4306/8000-0002 09.04.03 (16)

Touch Panel 600 Advanced Line

0762-5303/8000-0002 09.04.03 (16)

0762-5304/8000-0002 09.04.03 (16)

759-321 Terms

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 7

WAGO BACnet Configurator

Device

1

As of firmware version

0762-5305/8000-0002 09.04.03 (16)

0762-5306/8000-0002 09.04.03 (16)

Touch Panel 600 Marine Line

0762-6301/8000-0002 03.05.03 (17)

0762-6302/8000-0002 03.05.03 (17)

0762-6303/8000-0002 03.05.03 (17)

0762-6304/8000-0002 03.05.03 (17)

Edge Controller

752-8303/8000-0002 09.06.03 (18)

1

The above devices allow a 30-day period for activating a BACnet evaluation license.

Note

The devices are designated as “Fieldbus Coupler” or “Controller” below.

The compatible Touch Panels are also included in the places where the term “Controller”

is explicitly used!

1.1 Intended Use

The WAGO BACnet Configurator is an independent commissioning, configuration and

management software program:

• BACnet Controllers can be created.

• The project and the BACnet devices can be logically structured within a BACnet net-

work.

• Fieldbus couplers/controllers can be addressed.

• The client and server can be configured in each individual BACnet Controller.

• BACnet object properties can be visualized in the value browser.

Software operation is only permitted if the system requirements and license conditions

are met.

Warranty and Liability

The terms set forth in the General Business & Contract Conditions for Delivery and Ser-

vice of WAGO Kontakttechnik GmbH & Co. KG and the terms for software products and

products with integrated software stated in the WAGO Software License Contract – both

available at üwww.wago.com – shall apply. In particular, the warranty is void if:

• The products are used improperly.

• The deficiency (hardware and software configurations) is due to special instructions.

• The hardware or software has been modified by the user or a third party.

Individual agreements always have priority.

Obligations of Installers/Operators

The installers and operators bear responsibility for the safety of an installation or a sys-

tem assembled with the products. The installer/operator is responsible for proper installa-

tion and safety of the system. All laws, standards, guidelines, local regulations and ac-

cepted technology standards and practices applicable at the time of installation, and the

759-321Terms

8 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

instructions in the the products’ Instructions for Use, must be complied with. In addition,

the Installation regulations specified by Approvals must be observed. In the event of non-

compliance, the products may not be operated within the scope of the approval.

1.2 Typographical Conventions

Number Notation

100 Decimals: Normal notation

0x64 Hexadecimals: C-notation

‘100’

‘0110.0100’

Binary: In single quotation marks

Nibbles separated by a period

Text Formatting

italic Names of paths or files

bold Menu items, entry or selection fields, emphasis

Code Sections of program code

> Selection of a menu point from a menu

“Value” Value entries

[F5] Identification of buttons or keys

Cross References / Links

Cross reference / link to a section in a document

Cross reference / link to a separate document

ü

Cross reference / link to a website

Cross reference / link to an email address

Action Instructions

ü This symbol identifies a precondition.

1. Action step

2. Action step

ð This symbol identifies an intermediate result.

ð This symbol identifies the result of an action.

Lists

• Lists, first level

– Lists, second level

Notes

DANGER

Type and source of hazard

Possible consequences of hazard that also include death or irreversible injury

• Action step to reduce risk

759-321 Terms

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 9

WAGO BACnet Configurator

WARNING

Type and source of hazard

Possible consequences of hazard that also include severe injury

• Action step to reduce risk

CAUTION

Type and source of hazard

Possible consequences of hazard that include at least slight injury

• Action step to reduce risk

!

NOTICE

Type and source of malfunction (property damage only)

Possible malfunctions that may restrict the product’s scope of functions or ergonomics,

but do not lead to foreseeable risks to persons

• Action step to reduce risk

Note

Notes and information

Indicates information, clarifications, recommendations, referrals, etc.

Figures

Figures in this documentation are for better understanding and may differ from the actual

product design.

1.3 Legal Information

Intellectual Property

Unless barred by applicable legal provisions, unauthorized copying and distribution of this

document, as well as the use and communication of its content are strictly prohibited un-

less expressly authorized by prior agreement. Third-party products are always mentioned

without any reference to patent rights. WAGO Kontakttechnik GmbH & Co. KG, or for

third-party products, their manufacturer, retain all rights regarding patent, utility model or

design registration.

Third-party trademarks are referred to in the product documentation. The “

®

” and “

TM

”

symbols are omitted hereinafter. The trademarks are listed in the Appendix (8Protected

Rights [}156]).

759-321Terms

10 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

Subject to Change

The instructions, guidelines, standards, etc., in this manual correspond to state of the art

at the time the documentation was created and are not subject to updating service. The

installer and operator bear sole responsibility to ensure they are complied with in their

currently applicable form. WAGO Kontakttechnik GmbH & Co. KG retains the right to

carry out technical changes and improvements of the products and the data, specifica-

tions and illustrations of this manual. All claims for change or improvement of products

that have already been delivered – excepting change or improvement performed under

guarantee agreement – are excluded.

759-321 Security

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 11

WAGO BACnet Configurator

2Security

2.1 General Safety Regulations

• This documentation is part of the product. Therefore, retain the documentation during

the entire service life of the product. Pass on the documentation to any subsequent

user of the product. In addition, ensure that any supplement to this documentation is

included, if necessary.

• Any actions related to the use of WAGO software may only be performed by qualified

staff with sufficient knowledge to use the respective PC system.

Steps in which files are created or changed on a PC system may only be performed by

qualified employees with sufficient knowledge in the administration of the PC system

used in addition to file creation or modification.

Steps that change the PC system’s behavior within a network may only be performed

by qualified employees with sufficient knowledge of administration of the responsible

network.

• Comply with the laws, standards, guidelines, local regulations and accepted technol-

ogy standards and practices applicable at the time of installation.

2.2 Indirect Safety

• If automation solutions are implemented that can cause personal injury or major prop-

erty damage in the event of failure, you must take appropriate measures to ensure that

the system remains in a safe operating state even in the event of failure.

• Give all products in a network different IP addresses.

• Operate ETHERNET and PROFINET interfaces in separate networks.

• Never connect a PC on which a DHCP server is installed to a global network. In larger

networks, there is usually already a DHCP server that can cause collisions and subse-

quent network failure.

• Use only the latest security software.

• Uninstall or disable all software components or programs on your PC that are not re-

quired for the intended use.

• If there are access problems, check whether the e!RUNTIME runtime system is acti-

vated on the connected devices. Use a software tool (depending on the hardware) to

perform the check or use the Web-Based Management System.

759-321Requirements

12 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

3Requirements

3.1 System Requirements

Table3: Minimum System Requirements

Components Requirements

Operating system XP, Windows 7, Windows 8, Windows 10

Memory At least 128 MB

Free hard disk stor-

age

Minimum 10 MB for the WAGOBACnetConfigurator and 280 MB (x86) or 610 MB (x64)

for the .NET 4.0 Framework

1)

Monitor resolution 800 x 600 or greater

Miscellaneous Installed network card, .NET 4.0 Framework (redistributable included in delivery), net-

work cable or hub

Standard Internet connection to download software from ühttp://www.wago.com

Administrator rights for the installation/deinstallation and the first program start

External router

2)

(e.g., MBS BACnet router UBR-01)

1)

If .NET 4.0 Framework has not already been installed.

2)

Only for operation with a BACnet-MS/TP Controller 750-829.

759-321 Overview

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 13

WAGO BACnet Configurator

4Overview

The WAGO BACnet Configurator is an independent commissioning, configuration and

management software program. The WAGO BACnet Configurator offers a range of func-

tions; some are listed here:

• Design:

BACnet Controllers can be created.

• Structure:

The project and the BACnet devices can be logically structured within a BACnet net-

work.

• Addressing:

Fieldbus couplers/controllers can be addressed.

• Configuration:

The client and server can be configured in each individual BACnet Controller.

• Visualization:

BACnet object properties can be visualized in the value browser.

The WAGO BACnet Configurator displays all configuration data. To edit BACnet objects,

the WAGO BACnet Configurator offers specific table views in which the corresponding

properties of the object can be modified. Typical table editing functions, e.g., “Search/Re-

place,” “Sort,” “Filter” and “Show/Hide” are available. Then the updated configuration data

can be uploaded to one or more controllers and saved as a project.

759-321Installing

14 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

5Installing

This section describes the system requirements and installation of the WAGO BACnet

Configurator and the BACnet service BACstac for accessing BACnet/IP networks. The in-

dividual terms are described below:

• WAGO BACnet Configurator:

The Configurator can be used to configure and parameterize individual BACnet de-

vices.

• BACstac:

The BACnet Configurator gains access to a BACnet/IP network via this service. The

service is included in the BACnet Controller installation.

• BACnet/IP-Netzwerk:

Refers to a network consisting of one or more IP subnets that contain BACnet devices.

Note

Administrator rights required!

Administrator rights required! Administrator rights are required to install the BACnet Con-

troller. If these rights have not yet been authorized, contact your company IT department!

Note

Firewalls and virus scanners may prevent installation!

If an error occurs during BACnet installation, this may be due to an active firewall or a

virus scanner that is installed. It may be necessary to deactivate the virus scanner or fire-

wall being used while installation is in progress. As an alternative, manually accept the

BACstac in the firewall rules; this is never done automatically. Contact your system ad-

ministrator before performing either of these measures!

Note

Install BACstac to use the BACnet Configurator!

BACstac is automatically installed when installing the BACnet Configurator. Scanning for

network participants and their configuration in the BACnet Configurator is not possible

without installing BACstac.

Note

Activate the network connection to use BACstac!

An active network connection is required to install and use the BACstac.

Note

Additional Information

The WAGO BACnet Configurator is included in the product. This software from the down-

load area of the website http://www.wago.com under the appropriate product information.

759-321 Installing

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 15

WAGO BACnet Configurator

5.1 Installing the WAGO BACnet Controller

The particular WAGO BACnet Controller installation depends on the network used:

• “BACnet/IP” Network

• “BACnet MS/TP” Network

“BACnet/IP” Network

The WAGO BACnet Configurator has been installed on a PC. The PC is connected to the

BACnet/IP network via a switch, hub or router by a network cable. The usual require-

ments for an IP network apply here; e.g., a unique IP address and matching network

mask. This particularly applies to the products:

BACnet/IP Fieldbus Couplers/Controllers: 750-330, 750-332

BACnet/IP Controllers: 750-831, 750-831/000-002, 750-832, 750-832/000-002,

750-8212/000-100

“BACnet MS/TP” Network

The WAGO BACnet Configurator has been installed on a PC. The PC is connected to the

BACnet MS/TP network via a BACnet MS/TP router. This particularly applies to the prod-

uct:

BACnet MS/TP-Controller: 750-829

Note

BACnet communication is not possible via RJ45 interfaces!

The fieldbus controller (750-829) has two RJ45 interfaces. These interfaces cannot be

used for BACnet communication. With this product, BACnet communication is exclusively

through the MS/TP fieldbus!

1. Double-click on “WAGO BACnet Configurator Setup” to start the installation.

If the WAGO BACnet Configurator is installed on Windows 7 or higher, a dialog may

appear asking if the software can be installed. Confirm to proceed with the installa-

tion..

759-321Installing

16 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

2. Click [Next] to start the next configuration step.

3. Read the terms of the license carefully and select [I accept the agreement].

4. Click [Next].

759-321 Installing

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 17

WAGO BACnet Configurator

5. Enter the path to the desired Configurator installation location

6. Select the components to install; click [Next].

The components “BACnet Object Merger” and “Create Desktop Shortcut for WAGO

BACnet Configurator” options are selected by default. 8Information about the

“BACnet Object Merger” [}22].

759-321Installing

18 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

7. Click [Install] to continue the installation.

ð The Configurator has been installed

8. Click [Next] to finish the installation..

759-321 Installing

Product manual | Version: 2.1.0, valid from SW Version 1.14.0 19

WAGO BACnet Configurator

9. Click [Finish] in the installation window to end the setup.

ð The WAGO BACnet Configurator installation is finished. For information about poten-

tial general problems during the installation, refer to section 8Checking BACstac

[}21].

5.2 Network Settings for BACstac

If BACnet fieldbus couplers/controllers in the network are not automatically scanned

when the Configurator is launched, the BACstac may not be correctly installed. This may

be due to the following causes:

• Active firewall on the PC

• Incorrect network card IP address

• Stopped BACstac

If any of these apply, follow the steps below

5.2.1 Check Active Firewall

If an error occurs during BACnet installation, this may be due to an active firewall or a

virus scanner that is installed. It may be necessary to deactivate the virus scanner or fire-

wall being used while installation is in progress. As an alternative, manually accept the

BACstac in the firewall rules; this is never done automatically. Contact your system ad-

ministrator before performing either of these measures!

759-321Installing

20 Product manual | Version: 2.1.0, valid from SW Version 1.14.0

WAGO BACnet Configurator

5.2.2 Check Network Card IP Address

Note

Check IP settings before starting the BACstac!

The BACnet checks that the IP settings are assigned correctly. Make the IP settings be-

fore restarting the BACnet service.

1. Go to Tools > BACstac Settings in the BACnet Configurator.

ð The BACstac settings are displayed.

2. Click [Edit...] to open the BACstac configuration.

Note: Additional network segments can be added to BACstac through the button

[Add…]. Thus, several network segments can be searched simultaneously. Keep in

mind that a value from 2 to 255 can be added for Port ID network segments and 2 to

65534 for the “Network Number.”

Page is loading ...

WAGO BACnet Configurator User manual

WAGO BACnet Configurator User manual

Related papers

Other documents