FläktGroup ISYteqGO Bluetooth app Installation guide

Brand: FläktGroup

Model: ISYteqGO Bluetooth app

Type: Installation guide

ISYteq GO Bluetooth app manual

SETUP & COMMISSIONING USING THE APP

Table of Contents ISYteq GO Bluetooth app

2FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

1 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2 How to install the app. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Mobile device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3 How to start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1 Internet connection and bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.1 Starting the app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.2 Switching on the ISYteq controller . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.3 Logging into the app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

3.1.4 App connection to the server . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4 Main menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.1 Operating the app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

4.1.1 Menu description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5 Load a configuration file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5.1 XML preconfigured file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

5.1.1 Copy / send . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

5.1.2 Loading the default network project file . . . . . . . . . . . . . . . . . . . . . 6

5.2 Device selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5.2.1 Load default project . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

5.2.2 Selecting a device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

6 Device manual configuration of group network . . . . . . . . . . . . . 9

6.1 Device configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

6.1.1 Manual configuration of the internal group . . . . . . . . . . . . . . . . . . . 9

6.1.2 Naming and location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.2 Burger menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

6.2.1 MidTier configuration change . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6.2.2 BMS connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

6.4 Configuration of devices via the app . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

6.5 Configuration selection I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.6 Configuration selection of HMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

6.7 Configuration selection of BMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.8 Configuration selection of controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

ISYteq GO Bluetooth app Introduction

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 3

1Introduction

The FläktGroup mobile app is designed for use with an Android® phone only.

FläktGroup has taken every precaution to provide this app free from bugs and mal-

ware. Only download this app from a trusted source i.e. your local FläktGroup website

or from your local service engineer and FläktGroup sales representative.

Disclaimer

FläktGroup takes no responsibility for the loss of any data or malfunction to your phone

if the .app file has been downloaded from an unknown source.

2 How to install the app

2.1 Mobile device

•Open the mobile device.

•Open the app store.

•Search for the “ISYteq GO“ app.

•Download the “ISYteq GO“ app.

Fig. 1-1: Exemplary mobile

device

•Open the “ISYteq GO“ app.

Notice!

The app will be release on iOS in Q2 2023.

Notice!

During the installation you will be asked for some access rights for the

"ISYteq GO" app.

It must all be allowed.

How to start ISYteq GO Bluetooth app

4FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

3 How to start

3.1 Internet connection and bluetooth

Make sure you have an internet connection and switch on your bluetooth interface and

location sensor.

3.1.1 Starting the app

•Start the “ISYteq GO“ app on your mobile device.

3.1.2 Switching on the ISYteq controller

•Switch on the fan coil unit controller again and search for the device.

3.1.3 Logging into the app

•Click „Login“ and insert a location for the device.

User name: 3rd Service

Password: 3.Service03

•Enter the correct login data and click „OK“ [1].

Fig. 1-2:

3.1.4 App connection to the server

The app connects to the FläktGroup SE server.

The login data of the ISYteq GO controller will be downloaded.

Electric shock can lead to serious injuries or death!!

•Switch off the power to the ISYteq GO controller in the fan coil unit electrical

cabinet (never remove the SD card when the controller is switched on).

Notice!

You need to be in the range of the controller with your mobile device.

For Bluetooth, this typically means a range of <10 m distance between the con-

troller and your mobile phone.

Notice!

For connection to the FläktGroup SE server an internet connection is required.

ISYteq GO Bluetooth app Main menu

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 5

4 Main menu

The following describes the ISYteq GO “ISYteq GO“ app menu.

4.1 Operating the app

4.1.1 Menu description

There are 7 main menu points within the app to be aware of:

– Set points

– Allows a review of the current set point values in the controller via the app.

– Status

– Gives information about the current operational status of the controller and fan

coil unit operation, e.g. the comfort or economy mode.

– The profile status view

– Shows the current set point values etc. set on the controller for both economy

and comfort modes.

– Bypass mode

– Shows the settings in the controller of the bypass time for comfort switch from

economy to comfort mode or from the comfort mode to economy mode for a set

period.

5 Load a configuration file

5.1 XML preconfigured file

It is possible to create a configuration file with the device list creator and then download

this file to the mobile device.

Fig. 1-3:

Load a configuration file ISYteq GO Bluetooth app

6FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

5.1.1 Copy / send

•Copy/send the FGDefaultProject.xml to the mobile device from the computer.

5.1.2 Loading the default network project file

•Load the default network configuration file into the “ISYteq GO“ app.

•Click on the burger menu [1].

Fig. 1-4: Burger menu

Drop-down menu

•Select „Settings“ [1].

Fig. 1-5:

Notice!

The template is stored within the FCU package (HMIs/Devicelistcreator/FGDe-

faultProject.

ISYteq GO Bluetooth app Load a configuration file

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 7

•Select the initialization file [1].

Fig. 1-6: Initialization file

5.2 Device selection

5.2.1 Load default project

Apply the network settings after loading the default project file .xml.

•The controller will list the available devices.

•Search and select the device to connect with.

Select the beep button on the controller that you wish to communicate with when mul-

tiple fan coils are in the range of the bluetooth connection.

5.2.2 Selecting a device

After logging in, all ISYteq controllers that are within bluetooth range are displayed in

the lower areas under „Available devices“.

•Select a controller [1].

The selected controller [1] moves from „Available devices“ to „My devices“ and the

setting area of this controller is opened automatically.

•Click „Back“ to close the setting area.

•Select the three-dot menu [2] next to the selected controller.

Fig. 1-7:

Load a configuration file ISYteq GO Bluetooth app

8FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

•Select „Initialize device“ [1].

Fig. 1-8:

If the .xml file is not used, it is possible to set up the fan coil and fan coil unit network

manually.

Fig. 1-9:

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 9

6 Device manual configuration of group network

6.1 Device configuration

•Select „Identify“ [1].

This results in a loud signal tone on the corresponding board.

•Click „Identify“ [1] again to stop the signal tone.

Naming of the board

•Click „MidTier“ [2] to change the device name.

An input window opens in which you can enter the name.

•Click “OK” [3] to confirm.

Fig. 1-10:

6.1.1 Manual configuration of the internal group

If several controllers are controlled via a single control unit, a unit group must first be

created. The individual controllers must then be added to this group.

•Connect the controllers to each other via the RS485 interface, refer to the order

specific wiring diagrams.

The controllers must be set for the group via the app as follows.

Fig. 1-11:

Notice!

Select a name that can be uniquely assigned to the device.

Device manual configuration of group network ISYteq GO Bluetooth app

10 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

6.1.2 Naming and location

•Select „Identify“ [1] to locate the device and ensure you are making the name

change to the right device.

•Click on „MidTier“ [2] and change the name of the selected device.

•Click „OK“ [3] to confirm the name change.

Fig. 1-12:

6.2 Burger menu

•Go into the main menu.

•Select the burger menu.

•Select [1] on the burger menu to open the drop down selection.

Fig. 1-13:

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 11

6.2.1 MidTier configuration change

•Select „MidTier“.

A drop down menu appears.

•Select „Change device config.“ [1].

Fig. 1-14:

6.2.2 BMS connection

•Select „Interfaces“ to change the configuration for the BMS connection.

•Change the baud rate communication and address if necessary.

•Click „OK“ [2] to confirm the changes.

Fig. 1-15:

Notice!

Channel 1 is the designated connection to a BMS for the ISYteq GO.

Select this from the list if you wish to use the RS485 cable connection

via channel 1.

Device manual configuration of group network ISYteq GO Bluetooth app

12 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

•Ensure the bluetooth connection [1] is switched on.

Alternatively, it is possible to use a wireless connection for the BMS connection.

•Ensure the Bluetooth connection on your mobile device is switched on.

•Using the ISYteq GO APP select WLAN, refer to Fig. 1-19 on page 13.

Fig. 1-16:

•Click on the 3 dots to the right of the screen to select the „MidTier menu“ [1].

Fig. 1-17:

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 13

•Select „Change device config.“ [1].

Fig. 1-18:

•Click on the 3 dots to select „WLAN interface 1“ [1].

Fig. 1-19:

Device manual configuration of group network ISYteq GO Bluetooth app

14 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

•Change the necessary settings to use the local wireless LAN connection.

•Ensure DHCP [1] is activated.

(Enable the DCHP only if the IP addresses included in the XML file are configured

and it is ensured that the devices are equipped with fixed IP addresses. Contact

your IT department or the customer's IT department to discuss how they would like

to set this network of fan coil units up).

•Select the encryption under authentication type [2].

•Enter the network name under SSID [3].

•Enter the network password under password [4].

•When finished, click „OK“ [5].

The unit must be restarted.

•Click „Yes“ to restart the unit.

The restart takes about 10 - 30 second.

•Switch to the WLAN configuration.

•Read out the controller IP under IP address and make a note of these for future

reference.

Fig. 1-20:

The web server access is now possible with this IP.

6.3 Configuration of the master / slave controller

Configuration of the master controller

The operating device or, if applicable, the BMS is connected to the master controller.

•Click on the 3 dots to the right of the screen to select the master controller [1].

Fig. 1-21:

Notice!

It should be a secure connection and that the person responsible for

the IT network of the building or floor needs a password.

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 15

•Select „Change device config.“ [1].

Fig. 1-22:

•Select the three-point menu for RS485 channel 2 [1].

Fig. 1-23:

Device manual configuration of group network ISYteq GO Bluetooth app

16 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

•Enter the values for the master controller [1 -4].

•Ensure „Modbus Intercom“ is activated [5].

•Click „OK“ [6] to confirm.

Fig. 1-24:

Configuration of the slave controller

The following configuration must be carried out for each slave controller.

•Enter the data according to the illustration.

For slave 1, select Modbus address: 1

For slave 2, select Modbus address: 2

etc., up to slave 15.

•Click „OK“ [1] to confirm.

Fig. 1-25:

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 17

6.4 Configuration of devices via the app

•Go into the main menu.

•Select the burger menu.

•Select „Menu“ [1].

Fig. 1-26:

•Select „Operating“ [1].

The operating window opens.

Fig. 1-27:

Device manual configuration of group network ISYteq GO Bluetooth app

18 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

Select a menu item

Setpoints

•Select the „Setpoints“ in the menu.

•Set the required setpoint temperature to be assigned.

The operating mode, the setpoint of the fan operating mode, the temperature control

mode and the bypass mode of the device room are displayed here.

•Change according to application the operating mode, the setpoint of the fan

operating mode, the temperature control mode and the bypass mode of the device

room.

For details of these modes see the ISYteq GO operation manual.

Fig. 1-28:

Status

•Select the „Status“ in the menu.

Fig. 1-29:

Notice!

This window has no editing points and is for information only.

ISYteq GO Bluetooth app Device manual configuration of group network

FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications 19

Profile comfort

•Select the „Profile comfort“ in the menu.

The setpoints to be used in the comfort profile when the room is occupied are edited

here, e.g.

•Minimum setpoint

•Temperature setpoint

•Maximum setpoint.

The cooling offset sets the degree of offset from 1 - 4K (see controller manual for more

details).

The unit can also be set to operate in *Automatic or Manual mode for both fan and tem-

perature.

*Operate per schedule settings.

Fig. 1-30:

Valve adjustment

•Select the „Valves“ in the menu.

Valves – The unit will be either a 2-pipe or 4-pipe version.

•Change the version using the drop-down arrow.

•Change the K Hysteresis valve if necessary.

Please review the operation manual as to the options.

•Set the valve type. The control accepts 2- or 3-point valves.

Fig. 1-31:

Condensate

•Select the „Condensate“ in the menu.

Filter

•Select the „Filter“ in the menu.

•Return to the burger menu.

Device manual configuration of group network ISYteq GO Bluetooth app

20 FG_DC-10735-GB_ISYteq_Go_BT_APP_OM_R0-02-2023_150dpi • Subject to modifications

6.5 Configuration selection I/O

•Select „Configuration“[1].

Fig. 1-32:

I/O settings

•Select „I/O“ [1].

Fig. 1-33:

Page is loading ...

FläktGroup ISYteqGO Bluetooth app Installation guide

FläktGroup ISYteqGO Bluetooth app Installation guide

FläktGroup ISYteqGO Bluetooth app Installation guide

Related papers

Other documents