NCR 7409-K400 Instructions Manual

Brand: NCR

Model: 7409-K400

Type: Instructions Manual

NCR 7409-K400 is a CD/DVD ROM Drive kit that provides an integrated optical drive for the NCR 7409 terminal. This kit includes a SATA DVD ROM Drive, a CD/DVD bracket, and necessary cables for installation. The drive can be used to read and write CD and DVD discs, providing users with the ability to access and store data, music, videos, and other content. The kit also includes screws for securing the drive in place. Overall, the NCR 7409-K400 is a useful addition to the NCR 7409 terminal, expanding its capabilities and providing users with greater flexibility in data management and storage.

NCR 7409-K400 is a CD/DVD ROM Drive kit that provides an integrated optical drive for the NCR 7409 terminal. This kit includes a SATA DVD ROM Drive, a CD/DVD bracket, and necessary cables for installation. The drive can be used to read and write CD and DVD discs, providing users with the ability to access and store data, music, videos, and other content. The kit also includes screws for securing the drive in place. Overall, the NCR 7409-K400 is a useful addition to the NCR 7409 terminal, expanding its capabilities and providing users with greater flexibility in data management and storage.

7409‐K400

CD/DVDROMDrive

KitInstructions

Issue A

ii

Revision Record

Issue Date Remarks

A Jan 2009 First issue

1

Introduction

This kit provides an integrated CD/DVD ROM Drive for the 7409.

26958

DVD SATA and Power Cable

497-0455758

SATA DVD ROM Drive

006-8614321

Screw, M2 x 2.4 - 2.7mm, Phillips, Pan Hd

006-8611076

CD/DVD Bracket

497-0463593

2

Installation Procedures

Warning: Disconnect the AC power cord before disassembling the Terminal.

1. Remove the Display Head from its mount.

Removing the 7409 from the Table Top Mount

a. Release the Mounting Plate Latches and tilt the display back. Relock the latches.

26901

Mounting Plate Latches

b. Loosen the captive screw that secures the Cable Cover and remove the cover.

26690

Cable Cover Captive Screw

3

c. Disconnect the cables from the I/O Panel.

26445a

Terminal Power Cable

Printer USB Cable

Keyboard USB Cable

d. Release the Mounting Plate Latches and remove the 7409 from the mount.

26659

Mounting Plate Latches

Baseplate

4

Removing the 7409 from the Fixed Angle Mount

a. Remove the screws (2) in the sides of the Fixed Angle Mount.

26681

Screw

(One on each side)

5

b. Rest the bottom of the display on the Display Support.

26680

Display Support

Cable Cover Captive Screw

Note: Place the Display Support behind the extension on then Display Hinge

Bracket.

24753

Display Support

Bracket Extension

c. Loosen the captive screw that secures the Cable Cover and remove the cover.

6

d. Disconnect the cables from the I/O Panel.

Note: The Power Cable connector locks into position when connected to the terminal

and cannot be removed by simply pulling on the cable. You must grasp the connector

and slide the outside housing out from the terminal to unlock it from the terminal

connector.

26445

Terminal Power Cable

Printer USB Cable

Keyboard USB Cable

e. Slide the Locking Brackets (2) to the unlocked position.

24747

7

f. Remove the display from the Fixed Angle Mount.

24629

g. Disconnect the Power Cord from the I/O Panel on the terminal.

2. Lay the terminal face down on a flat surface.

3. Loosen the captive screws (2) that lock the Rear Cover.

26903

Captive Screws

Rear Cover

8

4. Pivot the Rear Cover to the open position.

5. Connect the DVD SATA and Power Cables to the Motherboard.

6. Install the drive.

a. Fold the cables under the CD/DVD ROM Drive as shown below.

b. Insert the two extensions on the CD/DVD RPM Bracket in the two slots in the chassis.

c. Secure the CD/DVD ROM Bracket with the thumbscrew.

26956

SATA

Power

Slots for CD/DVD ROM Bracket Extensions

Thumbscrew

Secured Here

9

26957a

Installed CD/DVD ROM Drive

7. Replace the Rear Cover and mount the Display Head to its mount using the reverse

procedures.

8. Close the Rear Cover and replace the Display Head to its mount using the reverse

procedures.

10

Accessing the DVD

The DVD is accessed by removing the Access Cover on the side of the display (1 screw).

26959

Access Cover

CD/DVD ROM Drive

1
2
3
4
5
6
7
8
9
10
11
12

NCR 7409-K400 Instructions Manual

Brand: NCR

Model: 7409-K400

Type: Instructions Manual

NCR 7409-K400 is a CD/DVD ROM Drive kit that provides an integrated optical drive for the NCR 7409 terminal. This kit includes a SATA DVD ROM Drive, a CD/DVD bracket, and necessary cables for installation. The drive can be used to read and write CD and DVD discs, providing users with the ability to access and store data, music, videos, and other content. The kit also includes screws for securing the drive in place. Overall, the NCR 7409-K400 is a useful addition to the NCR 7409 terminal, expanding its capabilities and providing users with greater flexibility in data management and storage.

Download PDF

Related papers

Other documents