NCR 7409 K065 Kit Instructions

7409‐K065

KioskFull‐PagePrinter

Pedestal

KitInstructions



IssueD

Revision Record

Issue Date Remarks

A Nov2009 Firstissue

B Aug2010 AddedinstallationproceduresforFiller

Plate/Keyboardoptions

C Mar2011 Added7409‐K076

D Sept2012 AddednewImagerkits

1

Introduction

Thiskitconsistsofthebottomportionofafloorpedestal,whichhousestheNCR2ST

Full–PagePrinter(TECK8)andpowersupply.TheUSBdatacableisalsoincluded.This

kitisusedinconjunctionwiththePrinterPedestalUpperCabinetKit(7409‐K060),

whichsupportstheNCRSelfServ60Kiosk(740

9)ortheNCREasyPointAdvantage

Kiosk(7404).

27

936

NCR 7404/7409 Kiosk

7409-K060 Upper Cabinet

7409-K065 Lower Cabinet

w/2ST Receipt Printer



2

Installation Procedures

Bolting the Pedestal to a Floor

Thepedestalshouldbeboltedtoafloor.Securethebasetothefloorwithboltsthat

areappropriateforthefloortype.Usethe16mm(5/8”)holes(4)locatedinsidethe

pedestal.

27745

Floor Mounting Holes

4 X 16 mm (5/8")

101 mm

(4.0 in.)

169 mm

(6.7 in.)

85 mm

(3.3 in.)

203 mm

(8.0 in.)



3

Installing the Upper Cabinet 7409-K060)

1. RemovetheDisplayBracketfromtheUpperCabinet(2screws).

27967

Display Bracket

Upper Cabinet



2. InstallthecorrectPowerSupplyBracket.

Note: The7409PowerSupplyBracketispre–installedintheUpperCabinet.If

youareinstallinga7404,replace theinstalledbracketwiththe7404PowerSupply

Bracket(2screws).

27935

7404 Power Supply

Bracket

7409 Power Supply

Bracket



4

3. Aligntheslots(4)onthebottomoftheUpperCabinetwiththetabs(4)onthetop

oftheLowerCabinet.

4. SlidetheUpperCabinettowardtherearoftheunittolockitintoposition.

2794

2

Slots (4x)

Tabs (4x)



5

5. SecuretheUpperCabinetwiththethumbscrews(2)locatedunderthetopofthe

LowerCabinet.

Note: Thereisathirdthumbscrewinthecenterofthecabinetthatisnotusedon

thismodel.

27940a

Not Used

Thumbscrews



6

6. InstalltheGrommetinthecableroutinghole.

27943

Grommet



7

7. InserttheTerminalPowerSupplyintothebracket.

2794

4

Terminal Power

Supply



8

8. ConnecttheTerminalACPowerCordtothePowerSupply.Routetheotherend

ofthecordoutsidethepedestal(seetheCableRoutingsection).

2794

5

Cable Routing Hole

A

C

Power

C

ord



9

Installing the Filler Plate/Keyboard Options

InstalloneofthefollowingoptionsonthefrontoftheUpperCabinet.

 PedestalFillerPlate(7409‐K061)

 PedestalFillerPlatewithN5680ImageScanner(7409‐K078)

 PedestalKeyboardTray(7409‐K063);requiresRuggedKeyboard(2336‐K212)

 PedestalKeyboardTraywithN5680ImageScanner(7409‐K080)

 Pedest

alKeyboardTrayw/MS3207BarCodeScanner(7409‐K064);requires

RuggedKeyboard(2336‐K212)

 PedestalPINPad/DipMSR(7409‐K068)

3

14

58a

7409-K061

7409-K063/2336-K212

7409-K064/2336-K212

7409-K068

7409-K078

7409-K080/2336-K212



10

Installing the Pedestal Filler Plate (7409-K061)

1. Alignthetabs(4)onthebackoftheFillerPlatewiththecorrespondingslots(4)on

thefrontoftheUpperPedestalCabinet.

2. SlidetheFillerPlatedowntolockitintoposition.

27970

Pedestal Filler Plate

(7409-K061)



11

Installing the Pedestal Filler Plate with N5680 Image Scanner (7409-K078)

1. Connectthescannercabletothescanner.

2. Alignthetabs(4)onthebackoftheFillerPlatewiththecorrespondingslots(4)on

thefrontoftheUpperPedestalCabinet.

3. SlidetheFillerPlatedowntolockitintoposition.

31459

Pedestal Filler Plate w/Scanner

(7409-K078)



4. Later,afterinstallingtheterminal,connectthescannercabletoaUSBportonthe

terminalI/Opanel

12

Installing the Pedestal Keyboard Tray (7409-K063)

Thiskitprovideshousingforthe2336‐K212Keyboard.

1. Insertthe2336‐K212KeyboardintothebottomofthePedestalKeyboardHousing

andsecureitwiththeRuggedKeyboardClamps(2)andHexNuts(8).

27980

Pedestal Keyboard Housing

2336-K212 Keyboard

Rugged Keyboard Clamp (X2)

Hex Nut (X8)



13

2. Alignthetabs(4)onthebackofthePedestalKeyboardHousingwiththe

correspondingslots(4)onthefrontoftheUpperPedestalCabinet.

3. SlidetheKeyboardAssemblydowntolockitintoposition.

29459

Pedestal Keyboard Tray

w/2336-K212 Keyboard



14

4. InserttheKeyboardBottomCovertabs(2)intothecorrespondingslots(2)inthe

bottomofthePedestalKeyboardHousingandUpperCabinet.

29460

Tab (X2)

Keyboard Bottom Cover



5. SecuretheKeyboardBottomCoverwithscrews(2).

29461



6. Later,afterinstallingtheterminal,connectthekeyboardcabletoaUSBporton

theterminalI/Opanel.

15

Installing the Pedestal Keyboard Tray w/MS3207 Bar Code Scanner (7409-K064)

Thiskitprovideshousingforthe2336‐K212KeyboardandaBarCodeScanner.

1. Insertthe2336‐K212KeyboardintothebottomofthePedestalKeyboardHousing

andsecureitwiththeRuggedKeyboardClamps(2)andHexNuts(8).

27980

Pedestal Keyboard Housing

2336-K212 Keyboard

Rugged Keyboard Clamp (X2)

Hex Nut (X8)



16

2. AttachtheMiniScanScannertotheScannerMountBracketwithscrews(3).

303

4

8

MiniScan Scanner

Scanner Mounting Bracket



3. SecurethescannertotheBottomKeyboardCover(2screws).

3034

9

Bottom Keyboard Cover



4. ConnecttheScannerCabletothe9‐PinD‐Shellconnectoronthescanner.

30350



17

5. Alignthetabs(4)onthebackofthePedestalKeyboardHousingwiththe

correspondingslots(4)onthefrontoftheUpperPedestalCabinet.

6. WiththetabsseatedintheslotsslidetheKeyboardAssemblydowntolockitinto

position.

30351

Pedestal Keyboard Tray

and 2336-K212 Keyboard



18

7. InserttheKeyboardBottomCovertabs(2)intothecorrespondingslots(2)inthe

bottomofthePedestalKeyboardHousingandUpperCabinet.

30352

Tab (X2)

Keyboard Bottom Cover



8. SecuretheKeyboardBottomCoverwithscrews(3).

30353



9. Later,afterinstallingtheterminal,connectthescannerandkeyboardcablestothe

terminalI/Opanel.

 ScannertoanRS‐232port(power)andaUSBport(data)

 KeyboardtoaUSBport

Page is loading ...

NCR 7409 K065 Kit Instructions

Related papers

Other documents