WaterLogic infiniti Operating, Installation And Service Manual

Brand: WaterLogic

Model: infiniti

Type: Operating, Installation And Service Manual

Waterlogic

77 McCullough Drive – Suite 9

New Castle, DE 19720

(888) 826-6597

Tech Portal Website: www.techportal.waterlogic.com

infiniti

OPERATING, INSTALLATION, AND SERVICE MANUAL

infiniti Operating, Installation, and Service Manual Page 2 - Revision: 9-15-2016

Waterlogic infiniti OPERATING, INSTALLATION, AND SERVICE MANUAL

Congratulations on your choice of the Waterlogic infiniti Water Treatment System, water treatment

system. The infiniti Water Treatment System, model dispenses cold, and hot. Every infiniti Water

Treatment System, includes:

Bio-Cote Anti-Microbial Protection

Filter configuration can be optimized for all water conditions

The Waterlogic infiniti Water Treatment System, provides exceptional quality and great tasting

water with every use.

TABLE OF CONTENTS

• Features and Benefits ................................................................. 3

• Certifications ............................................................................... 4

• Introduction and Safety Alert Symbols ....................................... 5

• Safety Precautions ...................................................................... 6

• Model and Part Designations ...................................................... 7

• Specifications .............................................................................. 7

• Operating Instructions ................................................................ 8

• Hot Tank Principles of Operation ................................................ 9

• Flow Diagram ............................................................................ 10

• Programming – Disabling Sleep Mode ...................................... 11

• Pre-Installation Procedures ...................................................... 12

• Draining Procedures.................................................................. 15

• Installation Procedures ............................................................. 18

• Cold Water Setting .................................................................... 20

• Replacement Components ....................................................... 21

• Hot Tank Descaling Instructions ............................................... 22

• Resetting the Overload or High Limit Safety ............................ 24

• Parts Drawings and Parts Lists .................................................. 26

• Electrical Diagram ..................................................................... 33

• Troubleshooting ........................................................................ 34

• Warranty .................................................................................. 54

infiniti Operating, Installation, and Service Manual Page 3 - Revision: 9-15-2016

Waterlogic infiniti FEATURES AND BENEFITS

Ambient, Cold and Hot Water

Cold and Hot Selections, which can be changed to Ambient and Cold settings to meet a wide range of

customer demands.

High Volume Storage and Water Capacity

Tower Model has 4 liters of Cold Water Capacity and 1.6 Liters of Hot Water Capacity.

Counter Top has 2 liters of Cold Water Capacity and 1.6 Liters of Hot Water Capacity.

BioCote®Anti-Microbial Protection

Plastic surfaces surrounding dispensing areas and drip tray are infused with an

exclusive silver additive called BioCote®. Silver is a natural anti-microbial that

inhibits the growth of microorganisms providing additional surface protection.

Leak Detection

infiniti Water Treatment Systems are supplied with a Sensor in the Leak Tray that halts water supply

to prevent overflow and sounds alarm to reduce accident potential.

Energy Saving Sleep Mode

Energy saving Sleep Mode can be programmed to turn off heater after 3 hours of inactivity.

Large Dispense Area with Recessed Faucet

9.84 inch dispense height with BioCote® recessed faucet to protect from cross-contamination.

Child Safeguard

The infiniti Water Treatment System defaults to cold water selection. Hot water must be actively

selected along with the dispense button and then dispensed within 1.5 second and defaults back to

cold water selection. If both buttons are not pushed at the same time, hot water will not be

dispensed. This feature eliminates the accidental dispensing

of hot water.

infiniti Operating, Installation, and Service Manual Page 4 - Revision: 9-15-2016

Waterlogic infiniti CERTIFICATIONS

Waterlogic water treatment systems have been tested, and certified to rigorous NSF and UL

Standards. We believe that performance testing and certifications validate Waterlogic as a world-

leader in water treatment systems.

infiniti Water Treatment System, Certifications Include

UL399 – Certified Drinking Water Cooler

Intertek Labs (ETL) Certified the infiniti Water Treatment System, to ANSI/UL 399

Standard for Drinking Water Coolers.

BPA Free - Waterlogic tests for BPA and declares that all of its products are Bisphenol-A

FREE and contain no harmful BPA plastics.

NSF/ANSI-61 – Certified Drinking Water System Components

NSF / ANSI 372 – Drinking Water System Components – Lead Content

CSA B483.1 - Drinking Water Treatment Systems

This System has been tested and certified in accordance with NSF/ANSI-61 – Certified

Drinking Water System Components, NSF / ANSI 372 – Drinking Water System

Components for low Lead Content, and CSA B483.1 - Drinking Water Treatment

Systems by the Water Quality Association (WQA)

Energy Star Certified

The infiniti Water Treatment System, has been tested and certified to the Energy Star,

a US Environmental Protection Agency (EPA) program that helps our customers save

money and protect our climate through superior energy efficiency.

Waterlogic manufacturing is certified to ISO 9001 – Quality Management

Systems (certified by Moody International). ISO 9001 is the

internationally accepted standard for well managed organizations that

have adopted the key quality management principles to its operations to

bring consistent quality products and a culture of continuous

improvement.

Safe Drinking Water Act

Waterlogic water treatment systems conform to the Safe Drinking Water Act (SWDA) “lead-free”

amendment effective January 4, 2014.

infiniti Operating, Installation, and Service Manual Page 5 - Revision: 9-15-2016

INTRODUCTION

Carefully read and follow all instructions to ensure proper and efficient operation of your infiniti

Water Treatment System. Contact Waterlogic or an Authorized Waterlogic Dealer if you have any

questions.

Waterlogic and Authorized Waterlogic Dealers employ trained service personnel who are

experienced in the installation, function and repair of Waterlogic equipment. This publication is

written for use by these qualified individuals. Waterlogic encourages users to learn about products,

however, we believe that product knowledge and service is best obtained by consulting Waterlogic

or an Authorized Waterlogic Dealer.

Waterlogic water treatment systems should be combined with selected water treatment

components to create a system specifically tailored for each application by trained and qualified

personnel.

Products manufactured and marketed by Waterlogic and its affiliates are protected by patents

issued or pending in the United States and other countries.

Waterlogic reserves the right to change the specifications referred to in this literature at any time,

without prior notice. Changes or modifications not expressly approved by Waterlogic could void the

warranty and user’s authority to operate the equipment.

SAFETY ALERT SYMBOLS

Read and follow all safety information carefully. The signal words used in this manual are selected as

shown below and based on an assessment of the degree of potential injury or damage (severe or

minor) and the occurrence of injury (definitely occurs or has the potential to occur) when the

warning is ignored:

DANGER!

Indicates a situation which, when not avoided, results in death or severe injury.

WARNING!

Indicates a situation which, when not avoided, has the potential to result in death or severe

injury; and/or severe property damage.

CAUTION!

Indicates a situation which, when not avoided, results or has the potential to result in minor

injury; and/or minor property damage.

infiniti Operating, Installation, and Service Manual Page 6 - Revision: 9-15-2016

SAFETY PRECAUTIONS

Basic safety precautions should be followed, including the following:

DANGER! If incorrectly installed, operated or maintained, this product can cause death or

severe injury. Those who install, operate, or maintain this product should be trained in its proper use,

warned of its dangers, and should read the entire manual before attempting to install, operate, or

maintain this product.

WARNING! Unit is to be used for its intended purpose as described in this manual, and

untrained individuals who use this manual assume the risk of any resulting property damage or

personal injury.

WARNING! HOT WATER. Unit produces Hot Water up to 188

F. Water above 125

F can cause

severe burns or scalding. Keep unauthorized people and children away from the unit to avoid

accidental dispensing of hot water. Children should not use without supervision.

DANGER! ELECTRICAL SHOCK HAZARD. Always unplug from power supply prior to servicing

equipment to prevent electrical shock.

WARNING! This system to be used for water only and is not intended for use where water is

microbiologically unsafe or with water of unknown quality without adequate disinfection before or

after the system. The system is designed for the supplemental bactericidal treatment of either

treated and disinfected public drinking water, or other drinking water, which has been tested and

deemed acceptable for human consumption by the state or local health agency having jurisdiction.

The system is designed to reduce normally occurring non-pathogenic or nuisance microorganisms

only. System is not intended for treatment of contaminated water.

WARNING! Dispenser Could Tip or Fall causing serious injury. Always install unit on a firm, flat,

and level surface and secure the infiniti Water Treatment System, to the base cabinet with the screw

provided to lock the components together. Never place heavy items on top of unit and never climb,

stand, or hang on unit or storage cabinet to prevent injury and damage.

CAUTION! INDOOR USE ONLY. Do not install outdoors or where unit is in direct sunlight. Do not

install where ambient temperature goes below 50°F or above 97°F. Avoid high humidity and

moisture. Product life and performance will be impacted and warranty could be voided.

infiniti Operating, Installation, and Service Manual Page 7 - Revision: 9-15-2016

MODEL/PART DESIGNATIONS

BRAND NAME DESCRIPTION

MODEL -

PART NUMBER

infiniti Cold and Hot

Charcoal and Silver Tower

Waterlogic

infiniti

- Cold and Hot –Tower

IIHCRC

F-5001-FS-HC-TT-CS-ION

infiniti Cold and Hot

Charcoal and Silver

Countertop

Waterlogic infiniti - Cold and Hot – Charcoal and Silver

Countertop

IIMHCRC

F-5001-M-HC-TT-CS-ION

SPECIFICATIONS

ITEM infiniti Hot and Cold infiniti Cold and Ambient

Water Connection ¼” Quick Connect

Cold Water Temperature

Cold Water Temperature – Factory Set Point 41° - 5°C

(Adjustable) 34° - 54° F. (1.1° - 12.2°C)

Hot Water Temperature Factory Set Point 185° F (85°C)

Hot Water Manual Reset

Overload

221° F (105°C)

Recommended Service

Pressure

40-60 psi (275-414 kPa) – Use Pressure Regulator

Maximum Service Pressure 100 psi (689 kPa) – Use Pressure Regulator

Rated Service Flow 0.5 gallons per minute (1.89 Lpm)

Environmental Temperature

35° - 100°F (2° - 37°C)

Heater 500 W

Refrigerant Gas R134a, 40g, 1.41 ounces R134a, 65g, 2.29 ounces

R134a Pressures High (230 psi), Low (90 psi)

SHIPPING SPECIFICATIONS

ITEM infiniti Counter Top infiniti Tower

Width/Depth/Height

13.75” x 15.25” x 19”

(35cm x 38.75cm

x 48.3cm)

13.5” x 14.5” x 40.5” (34cm x 41cm x

103cm)

Weight (dry)

42 pounds (19.5 kg)

58 pounds (26.5 kg)

ELECTRICAL SPECIFICATIONS

ELECTRICAL SUPPLY

120V/60Hz, 1PH

15 Amp Service

COMPONENT POWER (approximate) AMP DRAW (approximate)

Heater

800

6.6 Amps

Compressor 216 1.8 Amps

infiniti TOTAL

1016

8.4 Amps

#infiniti Counter Top is 19 inches. tall and may not fit between countertops and cabinets - Check installation to ensure adequate clearance.

infiniti Operating, Installation, and Service Manual Page 8 - Revision: 9-15-2016

OPERATING INSTRUCTIONS

The above picture shows front LED and control panel for the Waterlogic infiniti Water Treatment

System, water treatment systems.

Button Operational Use

Cold Water - Press Dispensing Button to start dispensing cold water until

desired fill. Cold Water is the Default Water Selection

Hot Water – Press and Release the Hot Water Selection Button followed

by pressing and holding the Dispense Button.

WARNING! Unit produces Hot Water up to 188°F (87°C). Water

above 125°F (52°C) can cause severe burns or scalding. Keep

unauthorized people and children away from the unit to avoid

accidental dispensing of hot water. Children should not use without

supervision.

Cold Water - Press and Release the Cold Water Selection Button followed

by pressing and holding the Dispense Button.

NOTE: Default selection mode is Cold Water. Selection will return to default after 3 seconds of

inactivity.

infiniti Operating, Installation, and Service Manual Page 9 - Revision: 9-15-2016

HOT TANK PRINCIPLES OF OPERATION

All Waterlogic Hot Tanks have a built in Vent or

Expansion Chamber in the top of the tank except for

WL270 (GF) units.

The Vent Chamber allows for expansion of the water

when it is heated.

The chambers are separated by a welded-in tank

baffle.

Water always flows into the bottom of the tank and

out the top to the faucet.

The hot tank outlet tube has a restrictor in its base.

This ensures the reservoir is always full by allowing

more water in than out.

There is a small hole in the side of the tank outlet tube

that allows air and water to pass into the vent

chamber as it is heated.

Water in the vent chamber is suctioned back through

the outlet tube vent hole when water is dispensed.

Expansion of water as it is heated in the reservoir will

push the water out the faucet when the outlet tube

vent hole becomes plugged with debris or scale.

The small Outlet Vent Hole is susceptible to scale build

up and is a key indicator that descaling is required.

It is critical to descale the hot tank through the vent

line and outlet line on a regular basis to prevent this

problem.

Descaling through the inlet and/or outlet lines only

will not clean the vent chamber and outlet vent hole

properly.

infiniti Operating, Installation, and Service Manual Page 10 - Revision: 9-15-2016

Waterlogic infiniti Water Treatment System, WATER FLOW DIAGRAM

Water In

Solenoid Valve

Water Out

Faucet

Condenser

Compressor

Filter Dryer

Cold

Tank

Hot Tank

infiniti Operating, Installation, and Service Manual Page 11 - Revision: 9-15-2016

PROGRAMMING INSTRUCTIONS

CHANGING ENERGY SAVER MODE TO NON ENERGY SAVING MODE

Infiniti UV Water Treatment System comes programmed to Energy Saver Mode. To turn off the

Energy Saving Mode, move the Jumper on CH6 from Pins 1-2 to Pins 2-3

Infiniti UV is programmed in Energy Saving Mode

from the factory

Jumper Pin Position – Pin 1 and 2

Turn off Energy Saving Mode

Jump Pin Position – Pin 2 and 3

Display PCB – P/N EN-0033-L00-00

Pin Numbers

Jumper Pin Part

Number EN-

6082

WLCP PN 20-

1005

infiniti Operating, Installation, and Service Manual Page 12 - Revision: 9-15-2016

PRE-INSTALLATION PROCEDURES

DANGER! ELECTRICAL SHOCK HAZARD.

Only qualified personnel who have read and understand this entire manual should attempt to

install, or service this unit, failure to do so could result in death or serious injury. DO NOT plug

into an electrical supply until specifically instructed.

WARNING! ALWAYS SANITIZE BEFORE USE.

Sanitize before use to eliminate any potential microbiological contaminates.

Materials Needed:

• Personal Protective Equipment. Rubber or Nitrile Safety Gloves and Protective Eyewear

• Phillips Screwdriver

• Temperature Gage

• Water Pitcher or Container to collect water from the faucet

• 5-gallon container or drain basin

• Sanitizer - Household Bleach (5.25% Sodium Hypochlorite) or Citric Acid Based Cleaner

• Tapered Tip Squirt Bottle

• ¼” Plastic Tubing, at least 4 feet in length, and assorted ¼” quick connect fittings

• TDS Meter and Test Strips for measuring chlorine - Optional

1. Unpack the Waterlogic infiniti Water Treatment System, and check exterior for damage.

Flush Filters

CAUTION! FILTER FLUSH REQUIRED.

infiniti Water Treatment Systems, are not supplied with filters. Filters should be configured to

optimize your system. Filters need to be configured and specified to do the job given the local

water conditions, usage, maintenance schedule, and placement restrictions.

In order for our filters to perform as represented and to provide the best quality water possible, it

is essential that filters be replaced periodically. The frequency of filter changes depends upon your

water quality and your water usage. For example, if there is a lot of sediment and/or particles in

your water, then you will have to change your filters more frequently than a location with little to

no sediment. Be sure to replace your filters whenever you notice a decline in the performance,

whether it is a drop in flow rate and/or pressure or an unusual taste in the water.

2. Flush thoroughly per filter manufacturers’ recommendation with fresh water to drain.

3. Once flushed, install the filters. Following the flow direction on the filter.

NOTE: Filters should not be flushed prior to 24 hours before installation to limit Microbial

Growth.

infiniti Operating, Installation, and Service Manual Page 13 - Revision: 9-15-2016

Sanitizing

Sanitize using a Household Bleach (5.25% Sodium Hypochlorite solution) or other approved

cleaner throughout the cold water circuit. Follow all instructions on the sanitizer and flush with

fresh water through the faucet until odor and taste is acceptable.

WARNING! USE PROPER PERSONAL PROTECTIVE EQUIPMENT

Always ensure proper ventilation and use proper personal protective equipment such as gloves

and eye protection when using chemicals. Refer to Material Safety Data Sheet for specific

requirements of each chemical product. Take all necessary precautions to prevent sanitizer from

contacting eyes, clothing, and any other surfaces in could damage (carpets).

4. Put sanitizer in the filter housing.

5. Turn off the water supply to the water cooler and release the internal water pressure by

depressing the dispense button momentarily and remove the water supply pipe.

6. Isolate the power to the water cooler.

7. Bypass the internal twist filters to avoid mixing sanitizing solution with the active carbon. This is

done by disconnecting the tubing to the inlet of the filters and attaching this tube to the inlet of

the solenoid valves.

8. Connect the outlet of the sanitizing filter housing to the inlet of the water cooler and connect the

supply water pipe to the inlet of the filter housing.

9. Turn on the power and water supply to the water cooler.

Fill the Cold Circuit with Sanitizer

10. Depress the cold water dispense button until the sanitization fluid starts to flow out of the faucet

nipple.

11. Allow the sanitization fluid to stand in the water cooler for 10 minutes. Do not let any

sanitization fluid enter the hot tank.

Flushing the Sanitizer from the Machine

12. Flush the cold water until the water runs clear of sanitizer.

13. Again isolate the water to the water cooler and release any internal water pressure.

14. Isolate the electrical power.

15. If this procedure is being done in conjunction with the annual service, change the filters.

infiniti Operating, Installation, and Service Manual Page 14 - Revision: 9-15-2016

WARNING! Use Personal Protective Equipment. Gloves and Eye Protection Required. The first

2 or 3 gallons of water will contain concentrated sanitizer. Use extreme care!

Fill the Hot Tank

16. Press the Hot Water Select Button, followed by the main dispensing button to fill the hot tank.

Water will dispense from the faucet once the hot tank is full. Flush until water is clear.

WARNING! HOT CIRCUIT IS NOT SANITIZED.

Water in the hot circuit is not sanitary until the temperature exceeds 171

F (77°C) for at least 5

minutes.

Heater Test

17. Always ensure tanks are full of water before turning on the heater or the overload (high limit) will

open and require manual reset. It will take the heater approximately 10 minutes to heat the

water from ambient 75°F (24°C) to the factory set point of 185°F (85°C). Dispense a cup of hot

water to ensure the temperature/odor/taste is acceptable.

WARNING! VERY HOT WATER CAN BURN OR SCALD.

Hot water should be dispensed carefully into insulated container to avoid injury.

infiniti Operating, Installation, and Service Manual Page 15 - Revision: 9-15-2016

Waterlogic infiniti COUNTER TOP DRAINING INSTRUCTIONS

Draining Notes

Drain the Waterlogic infiniti Water Treatment System for transportation.

WARNING! STORE UNIT EMPTY. ALWAYS SANITIZE BEFORE REUSE.

The unit must be completely drained and sealed before storing to avoid stagnation and reduce

microbial growth.

Prior to draining the hot tank, turn off the Red Heater and Compressor Power

Switch (O=OFF).

Allow Hot Water to cool off prior to draining.

WARNING! HOT WATER. The infiniti Water Treatment System produces Hot Water up to

188°F. Water above 125° can cause severe burns or scalding. Hot water should be dispensed

carefully into insulated container to avoid injury.

Disable Cold and Hot Tanks

1. Turn off the Red Heater and Compressor Power Switch (O-OFF) to disable the

heater and compressor.

Turn off Water Supply

2. Isolate the infiniti Water Treatment System from feed water by turning off the supply.

Drain the Cold Water Tank and Circuit

3. Remove the Front Cover.

4. Remove the Faucet, and move the Front Cover to the top of the infiniti Water

Treatment System to gain access to the draining tubes

5. Remove tubing from JG fittings, and

allow water to drain into drains,

catch basin, etc.

6. Reinstall tubing into JG fittings,

Faucet, and Front Cover

infiniti Operating, Installation, and Service Manual Page 16 - Revision: 9-15-2016

Waterlogic infiniti DRAINING TOWER INSTRUCTIONS

Draining Notes

Drain the Waterlogic infiniti Water Treatment System, for transportation.

WARNING! STORE UNIT EMPTY. ALWAYS SANITIZE BEFORE REUSE.

The unit must be completely drained and sealed before storing to avoid stagnation and reduce

microbial growth).

Prior to draining the hot tank, turn off the Red Heater and Compressor Power

Switch (O=OFF), and dispense 2 liters of hot water from the machine. As hot

water is dispensed from the faucet of the infiniti Water Treatment System,

colder water will be introduced into the hot tank. Since the Red Heater and

Compressor Power Switch is turned off, the heater will not energize and heat the

incoming tap water. Following this precaution prevents exposing personnel and equipment

(drains, catch basin, etc.) to scalding hot water.

Disable Cold and Hot Tanks

1. Turn off the Red Heater and Compressor Power Switch (O-OFF) to disable the

heater and compressor.

2. Dispense 2 liters of water through the hot tank to cool the water temperature

in the hot tank and avoid burns.

WARNING! HOT WATER. The infiniti Water Treatment System produces Hot Water up to 188°F.

Water above 125° can cause severe burns or scalding. Hot water should be dispensed carefully

into insulated container to avoid injury.

Turn off Water Supply and Bleed Water Pressure

1. Isolate the infiniti Water Treatment System from feed water by turning off the supply.

2. Dispense cold still water to relieve any pressure built up in the system.

infiniti Operating, Installation, and Service Manual Page 17 - Revision: 9-15-2016

Drain the Cold Water Tank and Circuit

3. Remove lower front panel to access tank feed lines.

4. Loosen the two screws holding the filter head

bracket to remove filter head bracket to access rear

of filter heads.

5. Disconnect tank line feed lines from hot and cold

inlet solenoids at rear of filter head fittings).

6. Catch hot (hot water should have cooled down after

dispensing 2 liters of water prior to the draining

process) and cold water drain into basin or catch.

7. Reconnect tubing into inlet elbows once drained, and reinstall

the filter head bracket.

8. Dry inside of unit if necessary.

9. Replace lower front panel.

infiniti Operating, Installation, and Service Manual Page 18 - Revision: 9-15-2016

INSTALLATION PROCEDURES

Safety and Installation Guidelines

Ensure all Local, State, and Federal Laws and Codes including health and safety guidelines are met

when installing Waterlogic Equipment. Only qualified service technicians should attempt

installation and service of Waterlogic Equipment.

WARNING! ELECTRICAL SHOCK HAZARD. Always unplug (isolate from power supply) to prevent

electrical shock except where electrical tests are specified.

WARNING! IMPROPER SUPPLY OR CONNECTION CAN RESULT IS RISK OF SHOCK.

Connect to a 15 amp 120V 60Hz properly grounded outlet (GFI is recommended). Ensure polarity is

correct and always use a 3-prong outlet. Consult a qualified electrician if you have any questions.

WARNING! USE ONLY Waterlogic SUPPLIED POWER CORD. Locate system within 5 feet of

power supply. Never use an extension cord or adapter. Do not use a damaged power cord or plug.

Keep power cord out of heavy traffic areas and away from heat sources. Do not, under any

circumstances, remove ground prong or alter the power cord. Never pull the power plug from the

outlet with a wet hand or allow the plug to get wet. Failure to use the supplied power cord will void

UL Certification and Warranty.

CAUTION! INDOOR USE ONLY. Never expose to direct sunlight, heat sources, or ambient air

temperature above 100°F (37°C) or below 35°F (2°C). Install indoors and keep unit away from

excessive humidity. Never expose to freezing temperatures. Ensure there is adequate clearance

around the unit to allow refrigeration system condenser to dissipate heat. Warmer environments

require more clearance around the unit. Minimum clearance around all surfaces of the machine is 2-

inches. Installs where the ambient temperature exceed 80F, require a minimum of 4-inches clearance

for proper heat dissipation and efficient operation.

CAUTION! USE A WATER PRESSURE REGULATOR. Waterlogic will not be responsible for injury or

damage caused by excessive water pressure. Operating pressure must be 40 psi to 60 psi. Be aware

any of potential pressure surges caused by building/municipal pumping stations.

CAUTION! USE UV STABILIZED SUPPLY LINES. Feed the unit with a potable ambient or cold

water supply only. Feed water over 100° F (37°C) can damage the treatment components. Water

block devices and external leak detectors are strongly recommended. Locate the unit as close to the

water supply and the electrical connections as possible.

WARNING! STORE AND TRANSPORT UNIT EMPTY. ALWAYS SANITIZE BEFORE USE.

The unit must be completely drained and sealed before storing to avoid stagnation and reduce

microbiological contamination (potential bacterial growth). Sanitize before use to eliminate any

potential microbiological contaminates

Pre-installation and sanitization procedures as prescribed in this manual must be performed before

installing the infiniti Water Treatment System,

Always install indoors and place the Waterlogic infiniti Water Treatment System, on a firm, flat and

stable surface.

infiniti Operating, Installation, and Service Manual Page 19 - Revision: 9-15-2016

1. Attach the water supply line to the 1/4” feed water inlet bulkhead fitting on the back of the unit.

Waterlogic requires the use of a water pressure regulator. Water feed pressure must be

between 40-60 psi. Turn on the water supply and check for leaks.

2. Check to ensure that the Red Heater Power Switch is the O=OFF position.

NOTE: Switches have internal LED that illuminates when placed in I=ON position.

3. Connect the power cord to the back of the Waterlogic infiniti Water Treatment System, and to a

120 Volt supply.

4. Fill the Cold Tank. Hold a container under the dispensing faucet, press and hold the main

dispensing button until a continuous flow of water is obtained. Once a continuous flow is

obtained, release the dispensing button. Cold tank is now full.

5. Fill the Hot Tank. Hold a container under the dispensing faucet. Press the Hot Select Button

followed by the main dispensing button until a continuous flow of water is obtained. Once a

continuous flow is obtained, release the main dispensing button. Hot tank is now full.

CAUTION! NEVER TURN ON HEATER BEFORE FILLING HOT TANK.

Red Heater Power Switch must be in the O=OFF position while the hot tank is empty. Damage

could occur within one minute and the overload (high limit) will require manual reset if heater is

turned on with an empty hot tank.

6. Move the Waterlogic infiniti Water Treatment System, into its final operating position. Be sure

that a minimum of 2” clearance is maintained around both the sides and the back of the unit.

This is important to allow proper airflow and heat exchange of refrigeration system.

7. Level unit using the adjustable feet to level if necessary. Never install on incline.

8. Turn the Red Heater Power Switch to I=ON position.

9. When the unit has reached its Hot Temp Set Point, the heater will cycle off. When the unit has

reached its Cold Temp Set Point Temperature, the compressor will cycle off.

10. Once the unit is at the target temperature(s), sample the water to ensure water meets

expectations and additional rinsing or adjustment is not required.

11. Check the unit for any leaks. External Leak Protection is always recommended.

infiniti Operating, Installation, and Service Manual Page 20 - Revision: 9-15-2016

ADJUSTING COLD SET POINT

Cold Water Temperature – Factory Set Point is 41°F (5°C) and can be adjusted to 34°F - 54°F (1.1°C to

12.2°C)

The cold set point can be adjusted by accessing the cold

thermostat adjustment screw under the decal at the rear of the

unit.

Remove the red portion of the Cold Tank Temperature label to

access the adjustment screw.

The factory set point is ~41°F and is indicated by the dot on

sheet metal.

Turning the adjustment screw clockwise to lower the set point

temperature.

Do not adjust past the “Max Cold” position at 3:00 position to

avoid freezing the cold tank.

Turning the adjustment screw counter-clockwise to raise the set

point temperature.

Page is loading ...

WaterLogic infiniti Operating, Installation And Service Manual

WaterLogic infiniti Operating, Installation And Service Manual

WaterLogic infiniti Operating, Installation And Service Manual

Related papers

Other documents