DMP Electronics 400 is a USB flash module that enables you to effortlessly update firmware for compatible panels in the field, eliminating the need for a computer and programming harness.
Key Features
- Effortless firmware updates via USB drive
- Compatible with a variety of panels, including XT30/XT50 Series, XTLC, XTLplus, and CellCom-LTE-V
- Easy-to-use interface with LED status indicator
- Supports FAT32 file system for flash drives
- Fast firmware update process, taking approximately 4.5 minutes
- Simple and intuitive operation with load button and jumpers
- Error detection with fast LED flashes indicating unsuccessful updates
DMP Electronics 400 is a USB flash module that enables you to effortlessly update firmware for compatible panels in the field, eliminating the need for a computer and programming harness.
Key Features
- Effortless firmware updates via USB drive
- Compatible with a variety of panels, including XT30/XT50 Series, XTLC, XTLplus, and CellCom-LTE-V
- Easy-to-use interface with LED status indicator
- Supports FAT32 file system for flash drives
- Fast firmware update process, taking approximately 4.5 minutes
- Simple and intuitive operation with load button and jumpers
- Error detection with fast LED flashes indicating unsuccessful updates
INSTALLATION GUIDE
Model 400 USB Flash Module
Description
The Model 400 USB Flash Module allows you to easily eld update
rmware for panels that would otherwise require the use of a computer
and a Model 399 Programming Harness.
The Model 400 is equipped with a standard USB 2.0 compatible Type
A female connector for interface to a USB Drive, a 4-pin connector
between the Model 400 and the compatible panel, and an LED to
indicate panel update status.
Compatibility
Compatible with XT30/XT50 Series panels, XTLC, XTLplus, and the
CellCom-LTE-V.
Caution: Do not connect a Model 400 to the CellComF-LTE-V if using 24 volt power.
Downloading the RU le to the USB Drive
To download a new rmware version RU le to the ash drive:
1. Connect a USB ash drive to your computer with a USB 2.0 compatible Type A female port.
2. Locate and download the panel’s rmware update RU le from DMP.com/Dealer_Direct and save it to the Root
directory of the ash drive.
3. When complete, disconnect the ash drive from your computer.
Note: The Model 400 only supports ash drives using a FAT32 le system. If multiple RU les are saved to the ash
drive, the le with the most recent Date Modied will be used by the Model 400.
Updating the Firmware
The Model 400 connects to the compatible panel via the panel’s programming PROG header. Updating rmware does
not change current panel programming. To update the panel with a new rmware version:
XT30/XT50
1. Remove the yellow and green wires from keypad bus terminals 8
and 9.
2. Connect the USB ash drive containing the RU le to the Model
400 and connect the assembly to the panel’s Programming PROG
header. The LED on the Model 400 will ash and then display
steady green.
3. Place a jumper across the Reset header.
4. Place a jumper across the Load header.
5. Remove the jumper from the Reset header.
6. Press and release the load button on the Model 400 to initiate
the rmware update. The LED on the Model 400 will ash slowly.
If the LED displays fast ashes it means the rmware update was
unsuccessful. The update will take approximately 4.5 minutes
and when complete the LED on the Model 400 will display steady
green.
7. Replace the jumper across the Reset header then remove the USB
ash drive and Model 400 assembly.
8. Remove the jumper from the Load header.
9. Remove the jumper from the Reset header.
10. Reconnect the yellow and green wires to terminals 8 and 9.
In the event the Model 400 USB Flash Module is inadvertently removed from the panel before
the update nishes, repeat steps 1 through 10.
Bottom
Top
4-Pin Connector
USB Connector
Load Button
View LED
Figure 1: Model 400 USB Flash Module
Figure 2: Model 400 USB Flash Module and
Flash Drive to XT30/50
J3
Phone
Line
J1
Ethernet
J16
Reset
J7 RJ
Supervision
J24
Celllular
header
connection
J18
Load
RED
PROG
J8
USB Flash Drive
4-Pin Connector
Model 400 USB Flash Module
Load Button on Underside
LED
800-641-4282
INTRUSION • FIRE • ACCESS • NETWORKS
www.dmp.com 2500 North Partnership Boulevard
Designed, Engineered and
Assembled in U.S.A.
Springeld, Missouri 65803-8877
LT-1402 © 2018 Digital Monitoring Products, Inc.
18252
Specications
Dimensions 3-3/8” L x 7/8” W x 1/2” H
Certications
FCC Part 15
CellCom-LTE-V, XTLplus, XTLC
1. Connect the USB ash drive containing the RU le to the Model
400 and connect the assembly to the panels Programming PROG
header. The LED on the Model 400 will ash then display steady
green.
2. Press and hold the Load switch on the panel. While holding the
Load switch, press and release the Reset switch, then release the
Load switch.
3. Press and release the load button on the Model 400 to initiate the
rmware update. The LED on the Model 400 will ash slowly. If
the LED displays fast ashes it means the rmware update was
unsuccessful. The update will take approximately 4.5 minutes
and when complete the LED on the Model 400 will display steady
green.
4. Press and release the Reset switch then remove the USB ash
drive and Model 400 assembly.
In the event the Model 400 USB Flash Module is inadvertently removed
from the panel before the update nishes, repeat steps 1 through 4.
Verify the Firmware
1. At a keypad, enter the Diagnostic code 2313 (DIAG), and press CMD.
2. Press CMD until Panel Settings displays. Press any select key.
3. Press CMD until Firmware Version displays. Verify the panel rmware version is correct.
4. Press CMD until Stop displays. Press any select key to exit the Diagnostic menu.
Figure 3: Model 400 USB Flash Module and
Flash Drive to XTLC
USB Flash Drive
4-Pin Connector
Model 400 USB Flash Module
Load Button on Underside
LED
RESET
S1
LOAD
S2
BAT
J7
PROG
RED
PWR
TX RF RX
SN
J1
-
1
-
2
DMP Electronics 400 is a USB flash module that enables you to effortlessly update firmware for compatible panels in the field, eliminating the need for a computer and programming harness.
Key Features
- Effortless firmware updates via USB drive
- Compatible with a variety of panels, including XT30/XT50 Series, XTLC, XTLplus, and CellCom-LTE-V
- Easy-to-use interface with LED status indicator
- Supports FAT32 file system for flash drives
- Fast firmware update process, taking approximately 4.5 minutes
- Simple and intuitive operation with load button and jumpers
- Error detection with fast LED flashes indicating unsuccessful updates
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
DMP Electronics XR550 series Troubleshooting Manual
-
DMP Electronics XT50 Series Installation guide
-
DMP Electronics XT50 Series System User's Manual
-
DMP Electronics 9800 Series Installation guide
-
DMP Electronics CellCom LTE Series Programming And Installation Manual
-
DMP Electronics CellCom-LTE-V SERIES Installation And Programming Manual
-
DMP Electronics 9862USB Installation And Programming Manual
-
DMP Electronics 9800 Series Installation And Programming Manual
-
DMP Electronics XTLplus SERIES Installation And Programming Manual
-
DMP Electronics XT50 Series Installation guide
Other documents
-
Digital Monitoring Products 400 USB Flash Module Installation guide
-
Digital Monitoring Products XTLC Programming Guide
-
Digital Monitoring Products LT 1912 Installation & Programming Guides
-
Digital Monitoring Products XTLplus GW Quick start guide
-
Digital Monitoring Products XTLC User guide
-
Digital Monitoring Products XTLplus Quick start guide
-
Clear-Com EclipseHX User manual
-
-
-
Digi BL4S200 User manual
