2. SDC
  3. LR100ARK-EM
LR100ARK-EM

SDC LR100ARK-EM User manual

  • Hello! I've reviewed the installation instructions for the SDC Electric Latch Retraction Device Kit LR100ARK-EM, designed for various Adams Rite vertical rod exit devices. This manual covers the assembly, electrical connections, and retrofitting steps for models 3100, 3600, 8100, 8200, 8500, and 8600. I'm ready to answer any specific questions you have about the device or its installation.
  • What is the operating voltage of the device?
    What exit device models is this device compatible with?
    What is the purpose of this document?
    What should I do if retrofitting to an existing vertical rod device?
P:\INST INSTRUCTIONS\ELR KITS\INST-LR100ARK-VERT-EM REV B 10-22 Page 1
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
LR100ARK-EM
ADAMS RITE ELECTRIC LATCH RETRACTION DEVICE KIT
VERTICAL ROD EXIT DEVICE EXTERNAL MODULE
MODELS: 3100, 3600, 8100, 8200, 8500 & 8600
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
Retrofit Installation Note: 42" or 48" exit devices that have been modified to fit a 36" or smaller opening, may not have
the required space to fit the standard E. L. R. assembly. Always verify the distance from the end of the touchpad to the
end rail, and if necessary, consult with the factory for appropriate selection.
*Visit: sdcsec.com/adamsrite
for Installation Video
Assemble brackets as shown
for different size Exit Devices.
For 36" or 42"
Devices
For 48"
Devices
ELECTRICAL DATA
24VDC @ 700/200mA
RED (+) BLK (-)
PATENT #8,851,530
Install the ELR bracket assembly
into device extrusion, over the
Push Bar support brackets.
Push Bar support
bracket
Remove End
Cap
Push Bar support
bracket
Remove End
Cap
P:\INST INSTRUCTIONS\ELR KITS\INST-LR100ARK-VERT-EM REV B 10-22 Page 2
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
When retrofitting to existing vertical rod devices, adjustment of the rods is required for proper operation of the Electric
Latch Retractor. Once the unit is properly installed, energize it so the latch is dogged down, then reconnect the vertical
rods to the device and make the proper adjustments to the rods.
Disconnect the spring-bolt latching assembly and use it to connect the ELR bracket assembly to the existing
components as shown.
Apply power to the ELR unit to make it draw the sliding latch bracket back to the open position. Secure in position by
tightening the set screws in the ELR assembly.
Slide ELR into back of device
and attach to bracket
assembly with supplied
screw.
Slide ELR into back of device
and attach to bracket
assembly with supplied
screw.
P:\INST INSTRUCTIONS\ELR KITS\INST-LR100ARK-VERT-EM REV B 10-22 Page 3
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
+-24vdc
ACCESS
CONTROL
BOARD PLACEMENT IN
POWER SUPPLY BOX
BOARD PLACEMENT IN
POWER SUPPLY BOX
SDC 600 SERIES
POWER SUPPLY
Latch
Retraction
Module
Pigtail
8 COND
18-22AWG
JACKETED CABLE
100' MAX
BLK
WHT
GRN
ORG
RED
BLU
BRN
YEL
Match colors with provided pigtail
Power
Transfer
Hinge
+-24vdc
ACCESS
CONTROL
BOARD PLACEMENT IN
POWER SUPPLY BOX
SDC 600 SERIES
POWER SUPPLY
Latch
Retraction
Module
Pigtail
8 COND
18-22AWG
JACKETED CABLE
100' MAX
BLK
WHT
GRN
ORG
RED
BLU
BRN
YEL
Match colors with provided pigtail
Power
Transfer
Hinge
Wire colors from provided Pigtail must connect to the same colors marked on PCB. If the Jacketed Cable does not have
the same colors as the Pigtail, use the following chart to mark the color connections from Pigtail to Jacketed Cable to PCB.
PIGTAIL
BLACK
RED
WHITE
GREEN
ORANGE
BLUE
BROWN
YELLOW
JACKETED CABLE
________________
________________
________________
________________
________________
________________
________________
________________
PCB
BLACK
RED
WHITE
GREEN
ORANGE
BLUE
BROWN
YELLOW
Wire colors from provided Pigtail must connect to the same colors marked on PCB. If the Jacketed Cable does not have
the same colors as the Pigtail, use the following chart to mark the color connections from Pigtail to Jacketed Cable to PCB.
PIGTAIL
BLACK
RED
WHITE
GREEN
ORANGE
BLUE
BROWN
YELLOW
JACKETED CABLE
________________
________________
________________
________________
________________
________________
________________
________________
PCB
BLACK
RED
WHITE
GREEN
ORANGE
BLUE
BROWN
YELLOW
/