SDC 6100ED RIM User manual

Brand: SDC

Model: 6100ED RIM

Type: User manual

SDC 6100ED RIM is a Yale electric latch retraction device that allows for remote control of door locks. It's designed for retrofit installation on 42" or 48" exit devices, making it suitable for various commercial and industrial applications. The device features a push pad for manual operation and can be integrated with access control systems for automated locking and unlocking. Its compact design and easy installation make it a convenient solution for enhancing security and access control.

SDC 6100ED RIM is a Yale electric latch retraction device that allows for remote control of door locks. It's designed for retrofit installation on 42" or 48" exit devices, making it suitable for various commercial and industrial applications. The device features a push pad for manual operation and can be integrated with access control systems for automated locking and unlocking. Its compact design and easy installation make it a convenient solution for enhancing security and access control.

LR100Y6K

YALE ELECTRIC LATCH RETRACTION DEVICE KIT

MODELS: 6100ED RIM

P:\INST INSTRUCTIONS\ELR KITSINST-LR100Y6K REV - 08-22 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

ELECTRICAL DATA

24VDC @ 700/200mA

RED (+) BLK (-)

PATENT #8,851,530

Retrofit Installation Note: 42" or 48" exit devices that have been modified to fit a 36" or smaller opening may not

have the required space to fit the standard E. L. R. assembly. Always verify the distance from the end of the touchpad to

the end rail and, if necessary, consult with the factory for appropriate selection.

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

INSTALLATION INSTRUCTIONS

Remove the Device End Cap and Cover from exit device. Replace the existing Cover End Cap with the provided

replacement End Cap packaged with ELR kit.

If present, remove mechanical dogging assembly. Use the provided Template to add required mounting hole. Drill

clearance as indicated for a 8-32 screw . Countersink the opposite side of rail extrusion.

Pre- Existing

Dogging holes

Replace existing Cover

End Cap with End Cap

provided with kit.

Drill clearance for 8-32 screw.

Countersink opposite side.

Template

Cover

Device End Cap

P:\INST INSTRUCTIONS\ELR KITS\INST-LR100Y6K REV - 08-22 Page 2

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Slide the ELR assembly into the rail extrusion over the Dogging Arm within the device. Loosen the Catch Screw if

required to allow for the ELR to be inserted over Dogging Arm. Fasten the ELR assembly to the rail extrusion of device

as illustrated below using the provided mounting screws from ELR kit.

Once kit is secured to the device depress the Push Pad and tighten the

Catch Screw on ELR kit to secure the Locking Pin in place. Release

Push pad and energize the ELR to verify operation. Re-install Cover with

new Endcap and Device End Cap.

Dogging

Arm

Catch Screw

Locking Pin

Push Pad

Dogging Arm

Catch Screw

Mounting

Screws

1
2

SDC 6100ED RIM User manual

Brand: SDC

Model: 6100ED RIM

Type: User manual

SDC 6100ED RIM is a Yale electric latch retraction device that allows for remote control of door locks. It's designed for retrofit installation on 42" or 48" exit devices, making it suitable for various commercial and industrial applications. The device features a push pad for manual operation and can be integrated with access control systems for automated locking and unlocking. Its compact design and easy installation make it a convenient solution for enhancing security and access control.

Related papers

Other documents