SDC QED111 User manual

Brand: SDC

Model: QED111

Type: User manual

SDC QED111 is an electric latch retraction device designed for use with 36" or larger exit devices. It allows for remote control of the latch, making it ideal for use in access control systems. The device operates on 24VDC power and can be easily installed by following the included instructions. The QED111 is compatible with SDC 600 series power supplies and features a compact design that fits easily into most exit devices.

SDC QED111 is an electric latch retraction device designed for use with 36" or larger exit devices. It allows for remote control of the latch, making it ideal for use in access control systems. The device operates on 24VDC power and can be easily installed by following the included instructions. The QED111 is compatible with SDC 600 series power supplies and features a compact design that fits easily into most exit devices.

LR100K2K-EM

ELECTRIC LATCH RETRACTION DEVICE KIT

MODELS: QED111, QED114 & QED124

P:\INST INSTRUCTIONS\ELR KITS\INST-LR100K2K-EM REV D 08-22 Page 1

Any suggestions or comments to this instruction or

product are welcome. Please contact us through

our website or email engineer@sdcsecurity.com

Carefully slide the assembly back out until the linkage JUST makes contact with the latch retraction rod. Tighten set

screws.

ELECTRICAL DATA

24VDC @ 700/200mA

RED (+) BLK (-)

PATENT #8,851,530

SET

SCREWS

TIGHTEN SET

SCREWS TO

LOCK DEVICE

IN POSITION

Short

Long

Remove and discard dogging from device. Slide the Electric Latch Retraction assembly into device and attach the

linkage to the latch retraction rod (short linkage for standard, long linkage for 4' device).

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

INSTALLATION INSTRUCTIONS

Retrofit Installation Note: 42" or 48" exit devices that have been modified to fit a 36" or smaller opening, may not have

the required space to fit the standard E. L. R. assembly. Always verify the distance from the end of the touchpad to the

end rail, and if necessary, consult with the factory for appropriate selection.

NOTE Retro-Fitting Vertical Rod Devices:

Before retro-fitting an electric latch assembly into a vertical device, the following must be done to ensure proper

alignment. Disconnect the vertical rods from the device. Install the electric latch assembly as shown above. Once the

ELR is properly installed energize it so that the push pad is dogged down, by doing so it will allow for proper alignment

for the vertical rods. Finally reconnect the vertical rods to the device and make the proper adjusments.

P:\INST INSTRUCTIONS\ELR KITS\INST-LR100K2K-EM REV D 08-22 Page 2

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM

[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

+-

24vdc

ACCESS

CONTROL

BOARD PLACEMENT IN

POWER SUPPLY BOX

SDC 600 SERIES

POWER SUPPLY

Latch

Retraction

Module

Pigtail

8 COND

18-22AWG

JACKETED CABLE

100' MAX

BLK

WHT

GRN

ORG

RED

BLU

BRN

YEL

Match colors with provided pigtail

Power

Transfer

Hinge

1
2

SDC QED111 User manual

Brand: SDC

Model: QED111

Type: User manual

SDC QED111 is an electric latch retraction device designed for use with 36" or larger exit devices. It allows for remote control of the latch, making it ideal for use in access control systems. The device operates on 24VDC power and can be easily installed by following the included instructions. The QED111 is compatible with SDC 600 series power supplies and features a compact design that fits easily into most exit devices.

Related papers

Other documents