SDC ED4200 User manual

Type
User manual

SDC ED4200 is a reliable electric latch retraction kit designed for retrofit or new installation on Corbin/Russwin exit devices. It allows for remote control of door latch retraction, enhancing security and convenience in various applications like access control systems, emergency exits, and restricted areas.

SDC ED4200 is a reliable electric latch retraction kit designed for retrofit or new installation on Corbin/Russwin exit devices. It allows for remote control of door latch retraction, enhancing security and convenience in various applications like access control systems, emergency exits, and restricted areas.

LR100CRK-EM
CORBIN/RUSSWIN ELECTRIC LATCH RETRACTION KIT
MODELS: ED4200, ED4800, ED5200, ED5400 & ED5800
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
P:\INST INSTRUCTIONS\ELR KITS\INST-LR100CRK-EM REV C 07-22 Page 1
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
INSTALLATION INSTRUCTIONS
ELECTRICAL DATA
24VDC @ 700/200mA
RED (+) BLK (-)
PATENT #8,851,530
Retrofit Installation Note: 42" or 48" exit devices that have been modified to fit a 36" or smaller opening, may not have
the required space to fit the standard E. L. R. assembly. Always verify the distance from the end of the touchpad to the
end rail, and if necessary, consult with the factory for appropriate selection.
Remove the End Cap, Mounting Plate, Cover, Cover Plug, Rail Housing and Dogging.
Attach Linkage to the
bottom cross bar
on the Push Bar
as shown
Linkage
Attach Linkage to the
Push Bar and the Electric
Latch Retraction Device
P:\INST INSTRUCTIONS\ELR KITS\INST-LR100CRK-EM REV C 07-22 Page 2
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: [email protected] ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
Attach the E.L.R. to the
Housing with the supplied
screws.
When retrofitting to existing vertical rod devices, adjustment of the rods is required for proper operation of the Electric
Latch Retractor. Once the unit is properly installed, energize it so the latch is dogged down, then reconnect the vertical
rods to the device and make the proper adjustments.
Replace Housing Cover, Cover with Plug, End Cap and the End Cap Cover.
+-
24vdc
ACCESS
CONTROL
BOARD PLACEMENT IN
POWER SUPPLY BOX
SDC 600 SERIES
POWER SUPPLY
Latch
Retraction
Module
Pigtail
8 COND
18-22AWG
JACKETED CABLE
100' MAX
BLK
WHT
GRN
ORG
RED
BLU
BRN
YEL
Match colors with provided pigtail
Power
Transfer
Hinge
  • Page 1 1
  • Page 2 2

SDC ED4200 User manual

Type
User manual

SDC ED4200 is a reliable electric latch retraction kit designed for retrofit or new installation on Corbin/Russwin exit devices. It allows for remote control of door latch retraction, enhancing security and convenience in various applications like access control systems, emergency exits, and restricted areas.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI