Deagostini Fiat 126p User guide

Type
User guide
PackPack
1919
STAGE PAGE
91 Engine compartment cover 309
92 Caravan front seat 312
93 Engine cover 315
94 Fitting the engine cover 318
95 Caravan left seat 321
Published in the UK by De Agostini UK Ltd, Royds Withy King, 65 Carter Lane, London EC4V 5EQ.
Published in the USA by De Agostini Publishing USA, Inc., 299 Park Avenue • New York, New York 10171.
All rights reserved © 2020
Warning: Not suitable for children under the age of 14.
is product is not a toy and is not designed or intended for use in play.
Items may vary from those shown.
309
Your parts:
91A. Engine compartment cover
91B. Engine compartment lock
91C. Spring
91D. Caravan front seat cushion
KP. 2 x 3 x 5mm screws
Stage 91: Engine compartment
cover
310
2Turn the cover over and secure the lock with a KP screw.
1Insert the engine compartment lock (91B) into the middle hole in
the engine compartment cover (91A).
3Insert the spring (91C) into the space in the cover under the
lock, up against the screw, as shown.
311
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
312
Your parts:
92A. Left engine air intake grille
92B. Right engine air intake grille
92C. Caravan front seat base
DP. 1.7 x 5mm screws
Stage 92: Caravan front seat
313
2Fit the left air intake grille in the same way as the right, into the
hole on the left side of the cover.1 Position the right engine air intake grille (92B) over the right hole
of the engine compartment cover (91A). The letter R on the grille
should be facing inwards. Press into position.
3Place the caravan front seat cushion (91D) into the two holes in
the caravan front seat base (92C). 4Secure the seat cushion with two DP screws.
314
6Secure the seat from underneath with two DP screws.
5 Place the assembled seat on the caravan floor, next to the cabinet,
aligning the holes of both.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
315
Stage 93: Engine cover
Your parts:
93A. Engine cover reinforcement
93B. Caravan left seat base
AM. 1.7 x 3mm screws
GM. 1.7 x 4mm screws
316
2Secure the reinforcement to the cover with two AM screws.
1 Place the engine compartment reinforcement (93A) onto the
inside of the engine cover.
3Tighten a further two AM screws into the sides of the
reinforcement. 4Finally tighten two GM screws into the indicated holes.
317
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
318
Stage 94: Fitting the engine cover
Your parts:
94A. Engine cover hinge block (2 pcs.)
94B. Engine cover hinge 1
94C. Engine cover hinge 2
94D. Caravan left seat cushion
MM. 1.7 x 3mm screws
RM. 2 x 5mm screws
CP. 1.7 x 4mm screws
319
3 Fit engine cover hinge 1 (94B) and the second engine cover
hinge block into place on the engine cover as shown. 4Secure the parts with two RM screws.
5Place the engine cover into the back of the body. Make sure that
the lock fits inside the body and that both hinges match the
corresponding holes below.
6Secure the hinges to the body with four MM screws.
2Secure the parts to the cover with two RM screws.
1 Place engine cover hinge 2 (94C) and one of the engine cover
hinge blocks (94A) in the location shown.
320
7 Place the caravan left seat cushion (94D) on the caravan left seat
base (93B), inserting the posts into the holes.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
8 Secure the parts together form inside the base with three
CP screws.
321
Your parts:
95A. 126P badge
95B. 650 badge
95C. Bonnet stop
95D. Stop loop
95E. Caravan left seat back
CP. Screws 1.7 x 4mm screws
OP. 1.7 x 4mm screws (countersunk)
Stage 95: Caravan left seat
322
3 Thread one end of the bonnet stop (95C) through the lower
hole in the stop loop (95D). Then wrap the stop around itself,
as shown.
4Fix the loop to the cover with two OP screws.
5Fit the posts on the underside of the caravan left seat back (95E)
into the corresponding holes along the left seat base. 6Secure the back with three CP screws.
2 Prepare a 650 badge (95B) in the same way and place it onto
the left side of the cover, as shown.
1 Place a 126P badge (95A) into cold water. Remove the badge
and separate from the backing paper. Place the badge into the
indicated point on the right side of the engine compartment cover.
323
7Place the left seat along the left side of the caravan floor aligning the
holes in the seat with the holes in the base.
Here is how your assembly should look at the end of this stage. Keep any assemblies, unused parts and spares labelled to one side for later use.
8 Secure the seat from below with three CP screws.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17

Deagostini Fiat 126p User guide

Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI