Page is loading ...
8.1CUSTOMER SERVICE PHONE: 1-800-426-8562
Section 8 - Electrical
PERGOLA®
Tech Tower Monitor Mount
Top Feed
Receptacle Switch
Low Voltage Kit
PDA
Cable Support
Ceiling, Light Trough
AB BB
CB
DB
EB
FB
IB
GB HB
JB
WARNING: Do not electrically interconnect modular power distribution
systems powered from two dierent power feed units. This poses a SHOCK
HAZARD to service personnel and will cause RISK OF FIRE due to excessive
circulating currents.
WARNING: Power to all branch circuits MUST REMAIN DISCONNECTED during
installation or removal of electrical components and raceway covers to avoid
SHOCK HAZARDS.
WARNING - Electrical connections shall be separated before any removal or
servicing of a mechanical connection.
In Canada, not more than 12 outlets to be supplied by one circuit.
WARNING: Do not electrically interconnect modular power distribution
systems powered from two dierent power feed units. This poses a SHOCK
HAZARD to service personnel and will cause RISK OF FIRE due to excessive
circulating currents.
WARNING: Power to all branch circuits MUST REMAIN DISCONNECTED during
installation or removal of electrical components and raceway covers to avoid
SHOCK HAZARDS.
WARNING - Electrical connections shall be separated before any removal or
servicing of a mechanical connection.
In Canada, not more than 12 outlets to be supplied by one circuit.
NOTE: Connections of this modular power distribution component MUST be done
by a licensed electrician, who must control the size and loading of each branch
circuit. The person or group installing Haworth products is responsible for
complying with all applicable building and electrical code requirements.
NOTE: Connections of this modular power
distribution component MUST be done by a licensed
electrician, who must control the size and loading of
each branch circuit. The person or group installing
Haworth products is responsible for complying with
all applicable building and electrical code
requirements.
Part #: PT15-7100 Revision: 1.0
8.2CUSTOMER SERVICE PHONE: 1-800-426-8562
Tech Tower Installation Ledge Installation (partial Height Tech Tower)
Remove cover
1
Horizontal Tile Rail - Tile
Horizontal Tile-Insert Rail
2Hook over top rail
OPTIONAL RAILS
AB
AB1
L
C
AB
AB
C
M
Part #: PT15-7100 Revision: 1.0
8.3CUSTOMER SERVICE PHONE: 1-800-426-8562
3install L-bracket
4install ledge
L
AB
AB2
AB2
AB
S155
AB3S-1
#10 x 1" Pan Head Screw
(S-1)
#10-24 Hex Nut
(S155)
Part #: PT15-7100 Revision: 1.0
Full Height Tech Tower
8.4CUSTOMER SERVICE PHONE: 1-800-426-8562
Hook over top rail and secure to bottom rail
5
AB
AB
C
C
AB4
AB
K
K
Part #: PT15-7100 Revision: 1.0
Remove connector
6
Reinstall connector and install cover
8
Remove PDA Install jumper Reinstall PDA
7
8.5CUSTOMER SERVICE PHONE: 1-800-426-8562
2
2
3
1
1 2 3
1
Only when installing second jumper - Step 7
AB1
AB1
AB
ABAB AB5
KB
KB
KB1
Part #: PT15-7100 Revision: 1.0
8.6CUSTOMER SERVICE PHONE: 1-800-426-8562
Monitor Mount Installation
Attach mounting brackets to tech tower
2
Remove cover
1
AB1 AB
AB
CB
Part #: PT15-7100 Revision: 1.0
Monitor Mount Installation
Adjust thumb screws
3
Attach backing plate to monitor
4
8.7CUSTOMER SERVICE PHONE: 1-800-426-8562
NOTE: Maximum load: 75 Kg. (165 lbs)
NOTE: Screws provided may
not cover all conditions.
TOP OF MONITOR
NOTE: Adjust thumb
screws until they touch
the tile or glass.
AB
BB
Part #: PT15-7100 Revision: 1.0
Install cover
5Hang monitor onto brackets and secure with anti-uplift screws
6
8.8CUSTOMER SERVICE PHONE: 1-800-426-8562
NOTE: make sure all 4
hooks are engaged.
12
AB1 AB
BB
BB
BB
CB
Part #: PT15-7100 Revision: 1.0
Top Feed Installation
Attach mounting brackets to top rail
1
2
8.9CUSTOMER SERVICE PHONE: 1-800-426-8562
Attach inner cover to bracket
1/8"
Drill 1
2
NOTE: Bottom slots for
option one and upper
slots for option 2.
Option 1 - Use Bottom Slots
Top Cap
Inner
Cover
Top Rail
Option 2 - Use Top Slots
Top Cap
Top Rail
Inner
Cover
DB1
DB1
DB1
DB1
DB
Part #: PT15-7100 Revision: 1.0
Plumb cover (M) and locate and cut a hole in ceiling tile
3
Attach junction box and install cover
4Install ceiling bezel
5
8.10CUSTOMER SERVICE PHONE: 1-800-426-8562
DB
DB2
DB
DB4
DB3
S144
DB
S135
S145
(S144)
#8-32 x 1/4" Pan Head Screw
#10-32 x 1/2" Screw
(S135)
#10 Hex Nut
(S145)
Part #: PT15-7100 Revision: 1.0
7Tie top feed to building
6Install electrical box cover
8.11CUSTOMER SERVICE PHONE: 1-800-426-8562
DB2
DB
DB5
Part #: PT15-7100 Revision: 1.0
1
2
8.12CUSTOMER SERVICE PHONE: 1-800-426-8562
PDA Installation
Cable Support Installation
TIGHTEN SCREW
2
APPLY PRESSURE
1
SNAP!
NOTE: Listen for a
“SNAP” sound.
EB
N
N
EB
FB
FB1
P
P
Part #: PT15-7100 Revision: 1.0
8.13
Ceiling, Light Trough
CUSTOMER SERVICE PHONE: 1-800-426-8562
Ceiling Light Trough
±1/8”
JB
JB
JB
JB
C
C
Part #: PT15-7100 Revision: 1.0
CUSTOMER SERVICE PHONE: 1-800-426-8562
Ceiling Light Trough - Round
±1/8”
8.14
JB
JB
JB
JB
A
A2
Part #: PT15-7100 Revision: 1.0
8.15CUSTOMER SERVICE PHONE: 1-800-426-8562
Optional - Receptacle Adjustments
1
Receptacle and Switch Installation
Remove face plate
MOUNT ON RIGHT SIDE
MOUNT ON LEFT SIDE
GB
NB
NB
LB LB
HB
GB
GB
NB NB
Part #: PT15-7100 Revision: 1.0
8.16CUSTOMER SERVICE PHONE: 1-800-426-8562
TIGHTEN SCREW
TIGHTEN
SCREW
APPLY
PRESSURE
APPLY
PRESSURE
2
1
2Install receptacle
2
1
Centerbeam Tile Rail
Vertical/Horizontal Tile-Frame Rail
Vertical Tile-Tile Rail
OPTIONAL RAILS
Power Installation with Plywood Backer
GB
GB
P
L
N
S
Part #: PT15-7100 Revision: 1.0
CUSTOMER SERVICE PHONE: 1-800-426-8562 8.17
3Attach connector to PDA
GB
EB
Part #: PT15-7100 Revision: 1.0
8.18CUSTOMER SERVICE PHONE: 1-800-426-8562
4 5 Install tileAdjust tile support as needed
6Attach face plate by snapping on
NOTE: Refer to Section 4
when installing Tiles.
NOTE: Adjust bracket
until it touches tile.
GB
GB
GB1
LB
LB
R
RR
Part #: PT15-7100 Revision: 1.0
Low Voltage Kit Installation
Insert junction box
1
2Secure junction box
4Install face plateInstall data plate
3
8.19CUSTOMER SERVICE PHONE: 1-800-426-8562
LB
R
R
R
R
MB
Part #: PT15-7100 Revision: 1.0
8.20CUSTOMER SERVICE PHONE: 1-800-426-8562
Wiring Diagram - Four-Circuit, 3+1
Power Routing Overview
PHASE
A
PHASE
B
PHASE
C
NEUTRAL
GROUND
Circuit L1- Black/Hot
Circuit L2- Red/Hot
Circuit L3- Blue/Hot
Circuit N1- Grey/Neutral
Circuit L4- Violet/Hot
Circuit N2- Grey Red/Neutral
Circuit G1- Bare/System Ground
Circuit G2- Green Yellow/Isolated Ground
In the four-circuit 3+1 schematic, Circuits 1, 2, and 3 are
supported with one shared neutral. Circuit 4 is supported
with a separate neutral.
N1
N2
G2
G1
L1
L2
L3
L4
= GREY (10GA)
= GREY RED (10GA)
= GREEN YELLOW (12GA)
= BARE COPPER (12GA)
= BLACK (12GA)
= RED (12GA)
= BLUE (12GA)
= VIOLET (12GA)
4 CIRCUIT WIRE COLOR
Three 208Y/120V Phase
Circuit Panel
On a 3-phase circuit panel, circuits are
distributed as shown.
A
B
C
D
Part #: PT15-7100 Revision: 1.0
/
