Page is loading ...
4.1
Components
CUSTOMER SERVICE PHONE: 1-800-426-8562
Section 4 - Tiles/Backer
PERGOLA®
Tile Plywood Backer & Brackets
Hanger Brackets
Electrical Support Beam
#10 x 5/8” Self Drilling
Pan Head Screw
(S265)
RS
T
U
S265
4.2CUSTOMER SERVICE PHONE: 1-800-426-8562
Plywood Backer - For Electrical
Height Subtract Location
A”
Plywood Backers with Electrical
-12” =X”
Determine location of plywood backer
1A
R
SS
CONDUIT ON
TOP
CONDUIT ON
TOP
TOP BOTTOM
NOTE: Power
installation, refer
to Section 8.
NOTE: Power
installation, refer
to Section 8.
CONDUIT ON
BOTTOM
CONDUIT ON
BOTTOM
OR
A - 12”=X”
A
12”
X”
A
12”
X”
R
A
12”
X”
NOTE: Center plywood
backer cutout as shown.
NOTE: Center plywood
backer cutout as shown.
C
L
C
L
C
LC
L
4.3CUSTOMER SERVICE PHONE: 1-800-426-8562
Plywood Backer - Non-Electrical
Determine random location of plywood backer
1B
R
S
X2”
X2”
NOTE: For non power
tiles locate plywood
backer as needed.
4.4CUSTOMER SERVICE PHONE: 1-800-426-8562
Plywood Backer
Mark location of plywood backer
with tape
2
Install rst bracket aligning with tape
3
S
25.5”
NOTE: Center brackets
with holes in plywood
backer (2 per side).
NOTE: If obstacles are
present, relocate brackets
to other locations from top
or bottom (as shown).
T
TOO CLOSE
TOGETHER
NOTE: Maximum distance between
brackets is recommended.
GOOD
CUSTOMER SERVICE PHONE: 1-800-426-8562 4.5
Plywood Backer
Attached plywood backer to brackets
5
#10 x 1-1/2" Tek Screw Self Drilling
(S104)
S
S104
#10 x 5/8” Self Drilling
Pan Head Screw
(S265)
BACK TO BACK
T
T
S265
Install 4 brackets per plywood backer
4
Receptacle
CUSTOMER SERVICE PHONE: 1-800-426-8562 4.6
Electrical Support Beam
Electrical Installation
U
U
U
3
4
51
TIGHTEN
SCREW
APPLY PRESSURE
2
U U U
Install electrical support beam
6
Refer to Section 8 when installing electrical
7
Switch
PDA
NOTE: Install rail within 6” of
power components to provide
stabilizing support.
EB
GB HB
CUSTOMER SERVICE PHONE: 1-800-426-8562 4.7
Tile Installation
Tile Removal
1 2
12
Install power tile rst then install non power tiles second. Refer to Step 9 for tiles under spanning tops.
8
1/8” (2.5mm) Reference
1/8” (2.5mm) Reference
1/8” (2.5mm)Reference
NOTE: Use cardboard
as a spacer reference
for the gap between
tile and rail.
NOTE: Check to make
sure tile connector is
attached properly.
NOTE: Install all
power tiles rst.
NOTE: Install
non-power tiles
after the power
tiles are installed.
NOTE: Use a pry
bar to remove tiles
as shown. Starting
from a corner.
IMPORTANT: ALWAYS
place pry bar on plastic
connector.
R
R
R
R
CUSTOMER SERVICE PHONE: 1-800-426-8562 4.8
Tile Installation
M
R
Spanning Top
(Full)
Spanning Top
(Half)
NA
OA
M
R
NA
Install spanning top rst, then install tiles
9
/
