2. Haworth
  3. 7021-7610b

Haworth 7021-7610b Operating instructions

  • Hello! I have analyzed the provided document, which provides detailed installation instructions for the HAWORTH ENHANCED PREMISE Adapter. This document covers the process of connecting Enhanced Premise panels to standard panels and door frames, including necessary tools and specific steps for various panel sizes. I am ready to answer your questions regarding the panel adapter installation process.
  • What tools are required for installation?
    What is the first step in connecting an enhanced panel to a standard panel?
    What should you do if the frame cutout height is greater than .915"?
1 of 5 7021- 7610 B
Part No: Rev.Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
297-100
ENHANCED PREMISE
®
ADAPTER, ENHANCED PANEL TO STANDARD PANEL
Installation Instructions
ENHANCED
PREM ISE
PANEL
1/4" Ball End
Tools required
STANDARD
PREM ISE
PANEL
T-45 (64" and 80" panels only)
For standard glass panel
modification only
2 of 5 7021- 7610 B
Part No: Rev.Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
297-100
1Remove existing standard panel
to which enhanced panel will connect
ENHANCED PANEL TO STANDARD PANEL
B
A
2Install light block (A) in adapter (B)
3For 64" and 80" standard PREMISE panels,
skip to step 5. For all other heights, overturn
panel and install panel lock (C)
STANDARD PREMISE
PANEL (O VERTURNED)
C
C
C
4Right panel if necessary, seat panel (D)
on adapter hooks (E), and engage
lock (C)
C
ED
1
2
5a (64" and 80" only) Tighten
top adapter lock (F).
F
3 of 5 7021- 7610 B
Part No: Rev.Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
297-100
ENHANCED
PREM ISE
PANEL
STANDARD
PREM ISE
PANEL
5b Reattach standard PREMISE panel with adapter to panel run.
7Install light block (A).
6Attach Enhanced PREMISE panel (with its connector installed)
to the adapter (see Panel Installation Instruction p/n 7021-7597).
A
4 of 5 7021- 7610 B
Part No: Rev.Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
297-100
1Remove existing standard door frame/glass panel to which
Enhanced panel will connect. Remove standard PREMISE
connector.
ENHANCED PANEL TO STANDARD
DOOR FRAME/GLASS PANEL
2Remove the connector mounting strip (A)
from side rail of frame (B)
A
B
.915"
REM O VE
EXCESS
3If frame cutout (C) height is greater than .915",
cut height of cutout to .915"
C
4Remove inner flange (D) from side rail (door frame only)
D
5Replace the connector mounting strip (A) in side rail
of frame (B).
STANDARD
PREMISE
DOOR
5 of 5 7021- 7610 B
Part No: Rev.Page:
E.C.O. No:
CUSTOMER SERVICE PHONE: 1-800-426-8562
297-100
A
1
7Seat door/glass frame (A) on adapter hooks (B).
10 Attach monolithic panel (C) to adapter (B)
(see Panel Installation Number p/n 7021-7597).
D
C
B
2
3
11 Install light block (D).
B
E
6Install light block (E) in adapter (B).
8Reattach standard Premise door frame/glass panel
with adapter to panel run.
Attach Enhanced Premise panel (A) (with its connector
installed) to adapter (B).
9
/