2. Cell2
  3. CR06
CR06

Cell2 CR06 User manual

  • Hello! I've reviewed the user manual for the LED Flush Mount Kit 86-F01610-0011.0. This document covers the wiring, operation, and installation of the device, including how to use its warning and cruise modes, synchronize multiple units, and select various available flash patterns. I'm ready to answer any questions you might have.
  • How to activate Warning Mode?
    How to activate Cruise Mode?
    How to synchronize lightheads?
    How to select a flash pattern?
For Simultaneous or Alternating Flash
1. Apply +VDC to RED and YELLOW wires simultaneously
to enter GROUPING MODE;
lighthead will display short (single or double) flashes:
• Single flash = Group 1
• Double flash = Group 2
2. Remove YELLOW wire from +VDC then momentarily
apply +VDC to change Groups:
• Lightheads of the same Group will flash together.
• Lightheads of different Groups will flash alternately.
3. Save and Exit the GROUPING MODE by powering off
the lighthead.
For Flash Pattern Selection
While in Warning Mode, momentarily apply +VDC to
YELLOW wire:
• once to next pattern
• quickly three times to FP#1
USER MANUAL
LED FLUSH MOUNT KIT
86-F01610-0011.0
WIRING
OPERATION
To +VDC to activate Warning Mode (fuse @ 3A) .........
RED
Apply +VDC to RED wire for High Power Operation in ECE R65 Class 2*.
To Chassis Ground ...............................................
BLACK
For Low Power Operation .............................................. WHITE
Apply +VDC to wires while RED wire is
activated for Low Power Operation in ECE R65 Class 1*.
To +VDC to activate Cruise Mode (fuse @ 3A) ........... GREEN
Precedence: Warning Mode > Cruise Mode
For Synchronization and Flash Pattern .................YELLOW
Connect YELLOW wires of all lightheads together for synchronization.
(All lightheads should be set to the same pattern)
*Actual approval will be based on the model purchased.
12-24VDC
* Actual approval will be based on the model ordered.
** For use with external flasher controller.
1
2
3
4
5
6
7
FLASH PATTERNS
8
9
10
11
12
13
14
15
16
Single
Double
Triple
Quad
Random
Steady EF**
Single
Double
Triple
Quad
Quint
Mega
Giga
Ultra
Single-Quad
Singe H/L
[R65*]
[2Hz]
[2Hz]
[2Hz]
[SAE][CA13]
[SAE]
[SAE]
[SAE]
[SAE]
[SAE]
17 Single-Triple-Quint
12-24VDC
Bracket Mount* (sold-separately)
INSTALLATION
Pop-n-Lock
Select a mounting location and drill an 1.14” (29mm)
cut-out, and then install the LIGHTHEAD onto the
cut-out.
1
Lighthead
Ø29mm
Front side of
the mounting surface
NOTE: Optical stripes
must align vertically to
meet regulation.
Ensure that the optical stripes are aligned vertically.
2
lens
Front side of
the mounting surface
Where necessary, apply silicone around the reverse
side to prevent from rotating.
3
Reverse side of
the mounting surface
Silicone
(user supplied)
Ensure that the optical stripes are aligned vertically.
2
From the front, install the LIGHTHEAD onto the
BRACKET.
1
Lighthead NOTE: Optical stripes
must align vertically to
meet regulation.
lens
SILICONE
SILICONE
Recommended Surface thickness @1.5~4.0mm
L-Bracket
L-Bracket
Where necessary, apply silicone around the reverse
side to prevent from rotating.
4
Silicone
(user supplied)
Mounting
surface
NOTE: To install more efficiently, use a rotating motion to
guide the LIGHTHEAD when installing onto the cut-out.
NOTE: To install more efficiently, use a rotating motion to
guide the LIGHTHEAD when installing onto the BRACKET.
SILICONE
SILICONE
Secure the BRACKET onto the desired mounting
surface with screws.
3
Screws (#6 x 18mm)
Torque Force: 4.9~5.9kgf-cm
Mounting
surface Mounting
surface
/