2. Cell2
  3. CR06
CR06

Cell2 CR06 User manual

  • Hello! I am an AI chatbot trained to assist you with the Cell2 CR06 User manual. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
  • What is the purpose of the device?
    How do you activate the warning mode?
    What is the precedence of the warning mode over the cruise mode?
    How do you connect the synchronization and flash pattern wires?
    How do you change the flash pattern?
    What are the different flash patterns available?
    What is the recommended surface thickness for installation?
    Where would you find the optical stripes?
    What is the torque required when mounting the L-bracket?
For Simultaneous or Alternating Flash
1. Apply +VDC to RED and YELLOW wires simultaneously
to enter GROUPING MODE;
lighthead will display short (single or double) flashes:
• Single flash = Group 1
• Double flash = Group 2
2. Remove YELLOW wire from +VDC then momentarily
apply +VDC to change Groups:
• Lightheads of the same Group will flash together.
• Lightheads of different Groups will flash alternately.
3. Save and Exit the GROUPING MODE by powering off
the lighthead.
For Flash Pattern Selection
While in Warning Mode, momentarily apply +VDC to
YELLOW wire:
• once to next pattern
• quickly three times to FP#1
USER MANUAL
LED FLUSH MOUNT KIT
86-F01610-0011.0
WIRING
OPERATION
To +VDC to activate Warning Mode (fuse @ 3A) .........
RED
Apply +VDC to RED wire for High Power Operation in ECE R65 Class 2*.
To Chassis Ground ...............................................
BLACK
For Low Power Operation .............................................. WHITE
Apply +VDC to wires while RED wire is
activated for Low Power Operation in ECE R65 Class 1*.
To +VDC to activate Cruise Mode (fuse @ 3A) ........... GREEN
Precedence: Warning Mode > Cruise Mode
For Synchronization and Flash Pattern .................YELLOW
Connect YELLOW wires of all lightheads together for synchronization.
(All lightheads should be set to the same pattern)
*Actual approval will be based on the model purchased.
12-24VDC
* Actual approval will be based on the model ordered.
** For use with external flasher controller.
1
2
3
4
5
6
7
FLASH PATTERNS
8
9
10
11
12
13
14
15
16
Single
Double
Triple
Quad
Random
Steady EF**
Single
Double
Triple
Quad
Quint
Mega
Giga
Ultra
Single-Quad
Singe H/L
[R65*]
[2Hz]
[2Hz]
[2Hz]
[SAE][CA13]
[SAE]
[SAE]
[SAE]
[SAE]
[SAE]
17 Single-Triple-Quint
12-24VDC
Bracket Mount* (sold-separately)
INSTALLATION
Pop-n-Lock
Select a mounting location and drill an 1.14” (29mm)
cut-out, and then install the LIGHTHEAD onto the
cut-out.
1
Lighthead
Ø29mm
Front side of
the mounting surface
NOTE: Optical stripes
must align vertically to
meet regulation.
Ensure that the optical stripes are aligned vertically.
2
lens
Front side of
the mounting surface
Where necessary, apply silicone around the reverse
side to prevent from rotating.
3
Reverse side of
the mounting surface
Silicone
(user supplied)
Ensure that the optical stripes are aligned vertically.
2
From the front, install the LIGHTHEAD onto the
BRACKET.
1
Lighthead NOTE: Optical stripes
must align vertically to
meet regulation.
lens
SILICONE
SILICONE
Recommended Surface thickness @1.5~4.0mm
L-Bracket
L-Bracket
Where necessary, apply silicone around the reverse
side to prevent from rotating.
4
Silicone
(user supplied)
Mounting
surface
NOTE: To install more efficiently, use a rotating motion to
guide the LIGHTHEAD when installing onto the cut-out.
NOTE: To install more efficiently, use a rotating motion to
guide the LIGHTHEAD when installing onto the BRACKET.
SILICONE
SILICONE
Secure the BRACKET onto the desired mounting
surface with screws.
3
Screws (#6 x 18mm)
Torque Force: 4.9~5.9kgf-cm
Mounting
surface Mounting
surface
/