Warrior Products S6922 Installation guide

Brand
Warrior Products
Model
S6922
Type
Installation guide

This manual is also suitable for

Warrior Products S6922 are side plates designed to be placed over the existing metal surface of your Jeep. They fit onto the rocker area between the fender wells with factory fenders but are also compatible with Warrior Tube Flares.

The plates are easy to install using drilled holes and pop-rivets. You can also use self-tapping screws or side-sided tape, but these methods are not covered in the installation guide.

To install the side plates, you should first clean the rocker panel surface where they will be installed. Ensure that any bare metal is primed or painted and that the surface is flat.

Warrior Products S6922 are side plates designed to be placed over the existing metal surface of your Jeep. They fit onto the rocker area between the fender wells with factory fenders but are also compatible with Warrior Tube Flares.

The plates are easy to install using drilled holes and pop-rivets. You can also use self-tapping screws or side-sided tape, but these methods are not covered in the installation guide.

To install the side plates, you should first clean the rocker panel surface where they will be installed. Ensure that any bare metal is primed or painted and that the surface is flat.

Warrior, Inc.
11100 SW Industrial Way
Tualatin, OR 97062
Phone: (888) 220-6861
Fax: (503) 692-0364
customerservice@warriorproducts.com
www.warriorproducts.com
Installation notes for:
6922 JL JEEP SIDE PLATES
Warrior products side plates are designed to be places over the existing metal surface of
the vehicle. The y fit onto the rocker area between the fender wells with factory fenders but are
also compatible with Warrior Tube Flares. Some Jeep variants may require the front edge to be
trimmed to fit.
Warrior’s recommended installation procedure for all side plates utilizes drilled holes and
pop-rivets. Other installations such as self-tapping screws and side-sided tape may be
adequate, but will not be covered in this installation guide.
Installation
1. Clean the rocker panel surface where the side plate will be installed. Ensure that any
bare metal is primed or painted and that the surface is flat.
2. If you are covering any rusted spots on the Jeep, do not attempt to pop rivet into these
places
3. You can use a RTV silicone sealant around the top and sides of the side plate. Leaving
the bottom edge ‘unsealed’ will prevent water collecting behind the side plate.
Choosing to use a sealant is completely at your discretion; however, debris and
moisture can build up between the body of the vehicle and the side plate, and could
potentially cause rust issues later on.
4. Because the JLs body is slightly curved, we recommend starting with the door trim
pieces. Place them on your doors where they fit best, keeping them level with one
another. Use tape to secure the trim in place.
5. Now you can position the front of the side plate level with the door trim pieces. The
rear will stick our due to the body curve.
6. Drill into the vehicle body using the side plate holes as a reference, only drilling out the
front three holes.
7. Put some clear RTV into the holes and rivet or screw the side plate to the vehicle.
8. With the front secure you can now work your way down the body using the same
process of drilling, placing RTV in the hole and then riveting or screwing the side plate
down.
9. Pay close attention to the level, the rear of the side plate has to be pushed in and up
slightly to match the front.
  • Page 1 1

Warrior Products S6922 Installation guide

Brand
Warrior Products
Model
S6922
Type
Installation guide
This manual is also suitable for

Warrior Products S6922 are side plates designed to be placed over the existing metal surface of your Jeep. They fit onto the rocker area between the fender wells with factory fenders but are also compatible with Warrior Tube Flares.

The plates are easy to install using drilled holes and pop-rivets. You can also use self-tapping screws or side-sided tape, but these methods are not covered in the installation guide.

To install the side plates, you should first clean the rocker panel surface where they will be installed. Ensure that any bare metal is primed or painted and that the surface is flat.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents