28 Bow and central wardooms, continued
28Glue the embellishments on the lengthwise bulkheads
175 and 177 and the embellishments on the transverse
bulkheads 176 and 178 on both sides of the previously
painted wardrooms. Fit the upper frames in the bow
wardroom 179 and 180 and the ends of the ceiling 181and
182. Fit the lower frames 183 and 184 and the skirting 185
and 186 in the bow wardroom. Glue the six portholes 80
(three on each side), glue the ceiling lining 187 and the
columns 188 in the bow wardroom. Carry out the same
operation with the parts 189, 190, 191, 192, 193, 194, 195,
196, 197, 198 and 80 for the central wardroom.
178
177
176
175
176 175
178
190
192
194
196 198 193
80 191
189 198
80
195
197
182
180
184
186 188 183
80 179
181 80
185
80
187
177
178
176
175
177
27 Bow and central wardrooms, continued 27With a mixture of bitumen and solvent
of approximately 30 per cent, stain the
embellishments 175 and 177 on the lengthwise
bulkheads, and the embellishments 176 and 178
on the transverse bulkheads for both
wardrooms.
30 THE CUTTY SARK: STEP BY STEP
199 26
26
26
80
200
199
26
80
26
199
202 201
200
201
202
29 Bow and central wardooms, continued
203
26
203
204
205
205
29With the parts 199, 200, 201, 202, 26
and 80, mount the six doors on the bow
wardroom, and with the parts 203, 204, 205
and 26 mount the two doors in the central
wardroom.
26
31 THE CUTTY SARK: STEP BY STEP
30 Mainmast pin-rails, bilge pump, storeroom and cages
32 THE CUTTY SARK: STEP BY STEP
30With the parts 206, 207, 208, 209, 210,
211 and 109, build the bilge pump. Glue
the masthole 154, and around this make ten
holes 0.8mm in diameter to fit the eyebolts
109. Make the pin-rails (see Step 26). Mount
the pin-rails, the bow wardroom, the netting
machine and the bilge pump. Glue the two bitts
110 and the four working warping heads 212.
With the parts 213, 214, 215, 216, 217, 218,
219, 220, 221, 222, 223, 224, 225, 226, 227,
228, 229 and 26 build the storeroom. With the
parts 230, 231, 232, 233 and 234 build the two
cages and stain them with a mixture of bitumen
and approximately 30 per cent solvent. With
the 0.5mm-diameter brass wire, make the bars
for the cages 235. Build the two stairs on the
bridgedeck with the sides 236 and the steps
237.
209
208
209
211
207
206 109 207 210
211
212 212
109
109 212
220
222221
216
229
223
214
227
26 228
234
230
231
232
235 232
231
231
233 234
233
231
231 232 233
231
234
219 225 218
226
213
224
223
227
222
215
237
236
217 218
213
221
220
212
154
110
diam. 0.8mm
33 THE CUTTY SARK: STEP BY STEP
31 Boat davits, wardroom on the bridgedeck and skylight opening
31Glue the central wardroom, the storeroom, the two cages and the two stairs on the bridgedeck. Glue the mizzen masthole 155, and around this
make five holes 0.8mm in diameter to fit the eyebolts 109. Make the holes indicated in the photo to fit the four boat davits 238. With the 2mm
brass straping 238a, make the hinges for the boat davits and fix the boat davits to the inside of the gunwale covers with the nails 26. Glue the bitts 110
to port and starboard. With parts 239, 240, 241, 242, 243, 244, 245, 246, 247, 248, 249, 250, 251, 252, 253, 254 and 80 build the wardroom on the
bridgedeck. First, stain parts 243, 244, 245, 247, 248, 249, 251 and 252. With the parts 255, 256 and 257 build and stain the skylight opening. Cut the
six pieces of glass 258 and glue them on the inside of the skylight.
110
26
238
212
212
242
239
241
247
253 80 80 254
252
80
248
247
250
249
246
251
249
239
238
243
80
245
257 256
258 255 256 255
258
257
80 243
244
80
80
109 155
109
238a
diam. 2mm diam. 0.8mm
diam.
0.8mm
diam.
1.5mm
diam. 1.5mm
240
1x4mm 1x4mm
34 THE CUTTY SARK: STEP BY STEP
32 Water barrels and bridgedeck finish
259 259
261
260
261
262
263
26
268
267
265
93
118
270
269
117
266
115
114
273
272
274 271
275
278
277 276
264
diam. 2mm
diam.
4mm
13mm
13mm
10mm
diam. 0.5mm
21mm
21mm 21mm 21mm 10mm
diam. 1mm
32Make a 2mm-diameter hole in the upper part of the water barrels 259, and use black paint to simulate the reinforcing rings around it. From
a 4mm-diameter rod, cut the pieces to make the barrel lids 260, and glue them as shown in the photo. Make the barrel handles 261 from
the 0.5mm-diameter brass wire. With the parts 262, 263, 264 and 26, build the two doors for the bridgedeck wardroom. Glue the skylight and the
battens forming the sliding door on the hood 265 of the bridgedeck. Following the measurements indicated, make 1mm-diameter holes to fit the
belaying pins 117 for the handrails. Insert the handrails 118. Glue the barrels 259 and, on both sides, make 0.5mm-diameter holes to fit the
eyebolts 93. Fasten the barrels with the lashing 266. Glue parts 114, 115, 267, 268, 269 and 270. With the parts 271, 272, 273, 274 and 275, build
the rudder wheel table. With parts 276, 277 and 278 build the stern grating.
35 THE CUTTY SARK: STEP BY STEP
18mm
15mm
33 Water barrels and stern deck finish, continued
279 110
110
109
282
281
280
33Glue the bitts 110 and the boom support 279. Fit the eyebolts 109
to port and starboard. With the parts 280, 281 and 282 build the
stern hatch, following the measurements given.
/
