2. Deagostini
  3. Cutty Sark

Deagostini Cutty Sark User guide

  • Hello! I'm a chat assistant and I've reviewed this assembly guide. This document provides detailed instructions on fitting parts to the bow deck of the Cutty Sark model ship. It includes steps to assemble the bow storeroom, latrine bilge pump, windlass and latrines. I'm ready to answer questions related to this guide.
  • What parts are needed to make the bow storeroom?
    Which parts are used for the latrine bilge pump?
    What parts construct the windlass?
    What parts construct the latrines?
126 128
127
122
121
124
125
123
125
26
24 Fit parts on bow deck, continued
27 THE CUTTY SARK: STEP BY STEP
24With parts 121, 122, 123, 124, 125, 126, 127, 128 and 26 make the bow storeroom. With
parts 26, 103, 129 and 130 make the latrine bilge pump. With parts 131, 132, 133, 134, 135
and 136 make the windlass and, with parts 137, 138, 139, 140, 141, 142, 143, 144, 145 and 146,
make the latrines.
130
140 140
142
143
143
139 144
141
144
142
146
145
141
137
139
130
131
131
132
132 133
134
134
136
135
129
129
103
103
diam.
1.5mm
diam.
1.5mm
26 26
25 Fit parts on bow deck, continued
25Fit the latrines and glue the network of stanchions 147 to the bow
rail. Make 2mm-diameter holes for inserting the anchor davits 148.
Fit the small eyebolts 93 and large eyebolts 109 into the ship’s hull, and
fit the anchors 149 with their stocks 150 with the help of the securing
chains 151 (red, yellow and blue arrows) and with the fine brown cotton
davit thread 153 (green arrows). Sand down the mastholes, following the
red lines 154 and 155. Make the stairs on the bow forecastle deck with
the sides, left 156, right 157 and the steps 158 cut to 12mm. Glue the
foretop masthole 154 on the deck. Make two 2mm-diameter holes to fit
the chain chock 159. Glue one end of the chain 151 around the windlass
and the other in the hole of the deck chain chock 159. Fit the two large
eyebolts on the bow 109 with the small rings 108. With the parts 160,
161, 162, 163, 164, 165 and 166 make and fit the two netting machines.
14 8
14 9
14 7
153
109
109
109
108
151 154 155
156
158
159
157
155
154
108
108
151
150
152
151
151
151
154
161
161
160
160
164
162
166
165 163 166
108
93
diam.
0.5mm
diam.
0.8mm
diam.
0.8mm
diam.
2mm
diam.
2mm
32mm
22mm
diam.0.8mm
diam.2mm
21mm
21mm
12mm
18mm
151
154 159
159
151
diam.0.8mm
28 THE CUTTY SARK: STEP BY STEP
26 Foremast pin-rail. Bow and central wardrooms 26Make the bitts 167, according to the
measurements indicated in the photo. In
the lower end of each bitt 167, make six holes
measuring 0.8mm in diameter. Fit the bitts into
the curved beam168 and insert the five
belaying pins 103. Paint the belaying pins 103 in
a dark colour. Glue the foresail masthole 154
and make 12 0.8mm-diameter holes to fit the
eyebolts 109. On both sides of the foresail
masthole, make 0.8mm-diameter holes to fit
the eyebolts 109 with their rings 108. Glue one
of the netting machines made in a previous
step. With the parts 169, 170 and 171, build the
bow wardroom and with the parts 172, 173
and 174, build the central wardroom.
103
103 168
167
167
109
154
109
108 168
103
167
109
109
108
167
167
168
15mm
diam. 0.8mm
diam. 0.8mm
diam.
0.8mm
diam.
0.8mm
diam. 0.8mm
10mm
5mm
3x5mm
171
169
170 169
170
174
173 172
173
172
29 THE CUTTY SARK: STEP BY STEP
/