Fiberplex WGF-12 User manual

Brand: Fiberplex

Model: WGF-12

Type: User manual

Fiberplex WGF-12 is a waveguide assembly designed for use in shield rooms or on ground planes. It provides a secure and reliable way to pass fiber optic cables through a wall or other barrier. The WGF-12 is easy to install and can be used with a variety of fiber optic cable types. It is also compatible with most standard fiber optic connectors.

The WGF-12 is a versatile device that can be used in a variety of applications, including:

Connecting fiber optic cables between different rooms or buildings
Providing a secure and reliable way to pass fiber optic cables through a wall or other barrier

The WGF-12 is a versatile device that can be used in a variety of applications, including:

Connecting fiber optic cables between different rooms or buildings
Providing a secure and reliable way to pass fiber optic cables through a wall or other barrier

GeneralInstallationInstructions

Donotunpackthewaveguideassemblyuntilyouarereadytoinstallit.Thiswillpreventdamagetotheexternalthreadsonthebushing.

1. Preparetheshieldroomwallorthegroundplanebyboringmountingholes1‐5/8”(1.625”)diameterinthedesiredlocation.Any

adjacentholesshouldbenocloserthan2.75”.

2. Cleanandde‐burrtheareaaroundthemountingholestoinsuresuitableelectricalcontactandatightsealwiththewaveguide

mountingnuts.

3. Unpackthewaveguideassemblytakingcarenottodamagethethreadedbushing.

4. Loosenthe1/4”capscrewwhichretainsthepluginthebushing(approximately2turns).

5. Taptheendofthecapscrewuntiltheplugseparatesfromthebushing.

6. Removethecapscrewandthewasherandstoreinasafeplaceforfutureuse.

7. Removetheplugfromthebushing.Theplugisfastenedtooneofthemountingnutsbyashortcabletopreventdamagetoits

surfaceafterinstallationandalsotopreventinjuryduringsubsequentremoval.Itisnotnecessarytodisconnectthecablefrom

eitherthemountingnutortheplug.

8. Removethefreemountingnutfromthebushing.

9. Placethebushingthroughthemountingholessothatthecableisfacingawayfromthemountingsurface.

10. Replacethemountingnutontheoppositesideofthemountingsurface.Centerthebushingbyholdingthenutandrotatingthe

bushinguntilthereareequalthreadsonbothends.

11. Atthispointthewaveguideisinplacewiththeplughangingbyitscableononeside.Iftheinstallationappearstobeacceptable,

tightenthemountingnutoppositefromtheplugendwitha2‐1/4”socketwrenchtoamaximumtorqueof85foot‐poundsorthe

maximumtorquethatthewallcanwithstandwithoutcrushing.

12. Installthefiberopticcablesbyinsertingtheconnectorsoneatatimethroughthecenterboreofthebushing,andthenpushthe

cablesintothegroovesaroundtheedges.

13. Afterallofthefiberopticcableshavebeeninstalled(donotoverfillthewaveguidebores),inserttheplugintothecenterbore

takingcarenottodamagethecables.

14. Presstheplugfirmlytolockitintoplace.

15. Installthecapscrewandwasherintotheplugcarefullysoastonotpushtheplugouttheotherside.

16. Torquethecapscrewto6foot‐pounds.

17. Plugmayberemovedfortheadditionorremovaloffiberopticcablesandthenreinstalledasrequired.

DONOTHEATORWELDTHISFILTER.DAMAGEMAYRESULT.

Warranty,ServiceandTermsandConditionsofSale

ForinformationaboutWarrantyorServiceinformation,pleaseseeourpublished‘TermsandConditionsofSale’.Thisdocumentisavailable

onfiberplex.comorcanbeobtainedbyrequestingitfrom[email protected]orcalling301.604.0100.

Disposal

DisposalofPackingMaterials

Thepackingmaterialshavebeenselectedwithenvironmentalanddisposalissuesinmind.Allpackingmaterialcanberecycled.Recycling

packingsavesrawmaterialsandreducesthevolumeofwaste.Ifyouneedtodisposeofthetransportpackingmaterials,recyclingis

encouraged.

DisposalofUsedEquipment

Usedequipmentcontainsvaluablerawmaterialsaswellassubstancesthatmustbedisposedofprofessionally.Pleasedisposeofused

equipmentviaanauthorizedspecialistdealerorviathepublicwastedisposalsystem,ensuringanymaterialthatcanberecycledhasbeen.

Pleasetakecarethatyourusedequipmentcannotbeabused.Afterhavingdisconnectedyourusedequipmentfromthemainssupply,make

surethatthemainsconnectorandthemainscablearemadeuseless.

Disclaimer

Theinformationinthisdocumenthasbeencarefullycheckedandisbelievedtobeaccurateatthetimeofpublication.However,noliabilityis

assumedbyFiberPlexforinaccuracies,errors,oromissions,norforlossordamageresultingeitherdirectlyorindirectlyfromuseofthe

informationcontainedherein.

USERMANUA

WaveguideWGF‐12



WGF12UM‐1611

18040-412 Guilford Rd. • Annapolis Junction, MD 20701

fiberplex.com • [email protected]

• 301.604.0100

Fiberplex WGF-12 User manual

Brand: Fiberplex

Model: WGF-12

Type: User manual

The WGF-12 is a versatile device that can be used in a variety of applications, including:

Connecting fiber optic cables between different rooms or buildings
Providing a secure and reliable way to pass fiber optic cables through a wall or other barrier

Download PDF

report

Fiberplex WGF-12 User manual

Fiberplex WGF-12 User manual

Related papers

Other documents