2. Halco Lighting Technologies
  3. HID36/840/MV/LED 84004

Halco Lighting Technologies HID36/840/MV/LED 84004, HID36/840/MV2/EX39/LED 84006, HID45/840/MV2/EX39/LED 84010, HID54/840/MV2/EX39/LED 84014, HID54/850/MV2/EX39/LED 84015, HID54/850/MV2/LED 84013 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Halco Lighting Technologies HID36/840/MV/LED 84004 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
ProLED
®
HID Retrot Installation Instructions
1 2
As shown in Figure 1;
Remove the old Ballast, Capacitor and Ignitor (if existing).
Warranty Information:
This product is warranted for 5 years from the date of purchase. If this product does not perform to the specications
supplied on this package, send an email to [email protected] or write to the address below for product return
and replacement. This replacement is the sole remedy available. Liability for incidental or consequential damage is
expressly excluded. Visit www.halcolighting.com for full warranty details.
IMPORTANT
READ INSTRUCTIONS CAREFULLY BEFORE INSTALLING. KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
ProLED lamps must be wired in accordance with the National Electrical Code and all applicable local codes.
Proper grounding is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE
APPLICABLE INSTALLATION CODE BY A QUALIFIED ELECTRICIAN WHO IS FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
WARNING - Risk of re or electric shock. ProLED HID Retrot Lamp installation requires knowledge of luminaires
and electrical systems. If not qualied, DO NOT attempt installation. Contact a qualied electrician.
WARNING - All the LED lamp models below can be used for dry or damp locations, DO NOT use where directly
exposed to water.
WARNING - Not for use with dimmers.
WARNING - Added weight of the device may cause instability of a free-standing portable luminaire.
OPERATING TEMPERATURE: -20° C to 60° C (-4° F to 140° F)
This device is not intended for use with emergency exits.
TURN OFF THE POWER
BEFORE INSTALLATION
.
Product Size:
Installation Steps:
L
N
Ignitor
Capacitor
Ballast
Fig 1
© 2016 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. Print Edition 11-05-16.
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Carlstadt | Cleveland | Houston | Los Angeles | Phoenix
3.43”
9.60”
36W
3.43”
10.79”
45W
3.43”
10.79”
54W
Installation Steps Continued:
3
4
As shown in Figure 2;
Connect A/C line voltage wires directly to EX39 socket.
(Reattach or replace ground lead if one is needed)
As shown in Figure 3;
Screw the LED lamp onto the corresponding socket.
L
N
Fig 2
Halco Lighting Technologies | 2940 Pacic Drive | Norcross, GA 30071 | Toll Free 800.677.3334 | Phone 770.242.3612 | Fax 800.880.0822 | halcolighting.com | Atlanta | Carlstadt | Cleveland | Houston | Los Angeles | Phoenix
Fig 3
L
N
© 2016 Halco Lighting Technologies, LLC. All rights reserved. Halco and ProLED are registered trademarks of Halco Lighting Technologies. All sizes and specications are subject to change. Print Edition 11-05-16.
/