Anova PLAC2424A Assembly Instruction

Type
Assembly Instruction
Assembly Instructions
Planter Lift and Level Kit
COMPONENT PARTS:
RECOMMENDED TOOLS:
ASSEMBLY:
Determine if the risers are needed. The risers are intended to help level the planter on uneven
surfaces and bump sides higher than others (up to 3/4") to account for imperfections in instal-
lation location. Use a level to determine what locations on the bottom of the planter will need to
be risen.
1.
2. Peel the label o on side of the adhesive pad and stick it to
one of the planter risers.
3. Remove the other label from the adhesive pad and stick the
planter riser to the planter bottom in the desired location.
4. If more than one riser in one location is necessary, use the
adhesive pad to adhere multiple risers together.
1
Level
Planter Riser Adhesive PadPlanter Sections
(Sizes and shapes may vary)
Ratchet 1/4" Socket1/4" Wrench
Hardware:
1/4" Bolt
1/4" Flat Washer 1/4" Nylock Nut
Contact Us:
800.231.1327
2
2.00
2.00
.75
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
NOTES:
MATERIAL: A356F ALUMINUM. APPROXIMATE CASTING WEIGHT: lbs
1.
PART VOLUME XX.XXX CU. IN.
2.
0.0625" RADIUS ON ALL INSIDE AND OUTSIDE CORNER UNLESS
3.
OTHERWISE SPECIFIED
PARTING LINE SHALL BE SMOOTH AND BLENDED WITHOUT
4.
EVIDENCE OF PARTING LINE LEDGE, GATE LOCATION, PARTING
LINES ARE SUBJECT TO ANOVAS APPROVAL.
CASTING MUST HAVE A NORMAL NON-FERROUS SAND CASTING
5.
FINISH THAT IS FREE OF VOIDS, SCRATCHES, SPLITS, DEFORMATION,
SINK MARKS OR CRACKS. - RMS 300 - 560
DEGAS FOR POWDER COATING
6.
THE THREE-DIMENSIONAL SOLID MODEL (SOLIDWORKS) IS THE
7.
MASTER DEFINITION OF THE PART.
THIS TWO-DIMENSIONAL DATA IS PROVIDED FOR INSPECTION AND
8.
REFERENCE PURPOSES ONLY.
ONLY CRITICAL DIMENSIONS ARE BEING SHOWN ON THIS
9.
DRAWING. THESE DIMENSION ARE CRITICAL IN THE ASSEMBLY AND
PERFORMANCE OF THE PART.
THE MANUFACTURING PROCESS SHOULD IMPLEMENT THE
10.
NECESSARY PROCESS CONTROL TO REDUCE TOLERANCE AND
VARIATION FROM THE NOMINAL DIMENSION.
STANDARD NOTES
VIEWS FOR PAGE 1
SIDE VIEW WITH ALL HEIGHT AND WIDTH DIMS CALLED OUT
1.
TOP AND BOTTOM VIEWS WITH OVERALL DIMS
2.
FRONT VIEW WITH OVERALL DEPTH DIMS AND LEG ANGLES IF
3.
NEEDED
SIDE VIEW WITH ALL ANGLES CALLED OUT
4.
ISO VIEW IN "SHADED WITH EDGES". NO DIMS NEEDED
5.
ADD WEIGHT TO NOTE 1
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
001
riser
SHEET 1 OF 1
2:1
4/14/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
r. Patterson
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
NOTE: It is recommended that there be 10" - 12" of space between the risers.
Planter Riser with Adhesive
36" Round Planter
Planter Risers with Adhesives
48" Rectangular Planter
Planter Riser Dimensions
3
Copyright 2022 Anova ® Manufactured in the U.S.9/23/2022
Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,
missing, or broken hardware, and general instability
Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
Repairs must be made using only factory authorized parts and methods.
WARNING
Do not drag the assembled unit across any surface.
This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove
surface dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
To locate the proper planter sections reference the Shop Drawings pro-
vided with the shipment. It has the Part Numbers and quantites listed.
Those part numbers will be cut out in the bottom half of the planter.
5.
Align the slots of each section and place them to where they are ush
with each other.
6.
Secure sections using the hardware provided. Place one at washer on
a hex head bolt and guide the bolt through the set of slots. Then place a
at washer on the other end of the bolt and secure with a nylock nut.
Tighten only nger tight until all hardware has been placed at each slot.
Reapeat this process for the remaining slots.
7.
Finally, tighten all locations with the ratchet, 1/4" socket, and 1/4"
wrench.
8.
Repeat Steps 7 & 8 to attach the remaining sections.9.
NOTE: It is recommended to assemble modular sections one at a time to ease in
assembly and keeping it level throughout the process.
Part Numbers
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova PLAC2424A Assembly Instruction

Type
Assembly Instruction

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI