1
HARDWARE NEEDED:
Step -by-Step Installation Sequence
anovafurnishings.com
800.231.1327 tel
Some products may require assembly before or during installation; please consult the assembly instructions if applicable.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum
and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
COMPONENTS NEEDED:
Elevation Benches and Chair Lounge Mounting Kit
Installation Instructions
1. Inspect the shipping container contents for damaged or missing components.
2. Lay all parts on a soft work surface or on the shipping packaging to prevent damage to nish.
NOTE: Before assembly, it is recommended that a light oil or petroleum jelly be applied to screw threads.
(2) Front Foot (2) Back Foot
1/4-20 x 1” Stainless Steel Screw
2
Elevation Benches and Lounge Chairs
Installation Instructions
3. Either nd the castings for your elevation bench or
lounge chair, or ip your assembled product over
onto a soft working surface.
4. Locate a Front Foot in the mounting kit. Secure
the foot to the front leg of the product with the
included 1/4-20 x 1” screw using a phillips head
screwdriver.
NOTE: The orientation of the Front Foot should be
going towards the back of the product underneath
the casting as shown in the image.
5. Locate a Back Foot in the mounting kit. Secure the
foot to the bottom of the rear leg of the product
with the included 1//4-20 x 1” screw using a phillips
head screwdriver.
NOTE: The orientation of the Back Foot should be
going towards the front of the product underneath
the casting as shown in the image.
6. Repeat steps 4 and 5 for the other casting/side of
your product.
7. Ensure that all of the feet are tightened in the
correct orientation prior to ipping your product
back over or assembling your product. Once
assembled take care to not damage the product’s
poweder coat while installing the product on the
stud anchors.
3
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
Step -by-Step Installation Sequence
anovafurnishings.com
800.231.1327 tel
Some products may require assembly before or during installation; please consult the assembly instructions if applicable.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a 3,000 psi minimum
and be cured for at least 28 days prior to the installation of the bench.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
8. Place the product in the desired location. Mark the
location of the holes with a pencil. To verify the
alignment of your anchor markings, reference the
foot mount sheet at the back of these instructions.
Elevation Benches and Lounge Chairs
8
Wrench / Socket Set
Mason Drill Bit Set
Hammer Drill
Safety Glasses
Pencil
Wire Brush
LevelHammer
SS or Rubber Washers
90107A127 OR 90130A050
OPTIONAL
B
A
3/8" x 5" 18-8
Stainless Steel Stud Anchors
92188A203
4
Elevation Benches and Lounge Chairs
Installation Instructions
9. It is recommended that you start holes in
sequential order from the smaller to the larger drill
bits to avoid oversized holes or holes drilled to
deep.
10. Evacuate debris from the mounting holes using
compressed air and a steel wire brush.
11. Locate an anchor and adjust the nut so it is ush to
the top of the anchor to protect the threads from
being damaged, and insert into the hole.
12. Use the hammer to x the anchor into the drilled
hole by giving it several hammer blows.
13. Repeat steps 2-5 until all anchors are installed.
14. Align the mounting holes of the bench or lounge
chair over the top of the anchors.
15. Care should be taken to avoid rubbing the powder
coating o the foot. Mount the bench to the
anchor using fasteners (B) and washers (C). Leave
hardware nger tight until all have been installed.
16. Verify the bench is level and aligned properly and
tighten all hardware.
9
12
16
11
14
5
• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose, missing, or
broken hardware, and general instability
• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced
• Repairs must be made using only factory authorized parts and methods.
WARNING
• Do not drag the assembled unit across any surface.
• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove surface
dirt. Do not clean with a solvent or petroleum based products.
CARE AND
MAINTENANCE
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
FOOT MOUNT(S)
02/07/2023 Copyright 2023 Anova ® Manufactured in the U.S.
Elevation Benches and Lounge Chairs
Installation Instructions
FF
17.50
69.75
SECTION F-F
SCALE 1 : 6
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Bench, Thermory, Elevation
001
SHEET 1 OF 1
1:12
12/29/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
ELV80T
69.75"
17.50"
Elevation Bench Foot Mount
FF
17.50
69.75
SECTION F-F
SCALE 1 : 6
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Bench, Thermory, Elevation
001
SHEET 1 OF 1
1:12
12/29/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
ELV80T
FF
17.50
69.75
SECTION F-F
SCALE 1 : 6
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
MATERIAL: 12GA (.1046) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 1.25" SQUARE X 12GA (.109") WALL
TUBING, ASTM A513, HRPO
MATERIAL: 10GA (.1345) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 14GA (.0747) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
SHEET METAL GAUGES
TUBING METAL GAUGES
MATERIAL: 1.25" SQUARE TUBING, 12GA (.109")
WALL, ASTM A513, HRPO
RECYCLED PLASTIC NUMBER BOARD PROFILES
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 2 X 4 PLANK
MATERIAL: RECYCLED HDPE (HIGH DENSITY
POLYETHYLENE) 1 X 4 PLANK (ACTUAL: 1 X 3-1/2")
MATERIAL: 2.3750 10GA (.134) WALL TUBING,
ASTM A500 GRADE B 50,000 PSI MIN YIELD,
58,000 PSI MIN TENSILE, HRPO
STANDARD NOTES
DEBUR DASH LINE ONLY
MATERIAL: 7GA (.1793) A1011 CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 2.375" OD X 10 GA HRPO
TURRET PUNCH
PART IS REVERSIBLE
MATERIAL: .5000" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: .2500" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: Ø2.00 X 12 GA. (.109) WALL ASTM
A-513 ELECTRIC WELD TUBE TYPE 1 CARBON
STEEL, PICKLED AND OILED
MATERIAL: .1875" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
MATERIAL: 3/4 #9 FLAT EXPANDED STEEL
PERFORATED OR EXPANDED METAL
MATERIAL: .3750" ASTM A1011, CS TYPE B, (CQ)
CARBON STEEL, HRPO
REMOVE SHARP EDGES
REVISIONS
REV.
DESCRIPTION
ECN TR #
DESIGNER
DATE
001
ORIGINAL PRINT
NONE
Bench, Thermory, Elevation
001
SHEET 1 OF 1
1:12
12/29/2022
REV
DWG. NO.
B
SIZE
TITLE:
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125± .0625 DURING COATING.
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
DRAWN
DATE
TOLERANCES UNLESS NOTED:
X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX ± .015625 ANGULAR ± 1°
A A
B B
4
4
3
3
2
2
1
1
SCALE
ELV80T
17.50"
27.76"
Elevation Lounge Chair Foot Mount
-
1
-
2
-
3
-
4
-
5
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Anova RLA60R Installation guide
-
-
-
-
-
-
-
-
-
