Anova D6013 Installation guide

Type
Installation guide
anovafurnishings.com
888.535.5005 tel
Installation Instructions
TOOLS NEEDED: HARDWARE NEEDED:
A2374 KIT:
Step-by-Step Installation Sequence
Product requires assembly before installation.
Examine the footing or slab for damage or defects. The footing or slab should be reinforced concrete rated at a
3,000 psi minimum and be cured for at least 28 days prior to the installation of the table.
CAUTION: Oversized holes and holes drilled too deep in the concrete will make it dicult to set the anchor.
!
Hammer DrillHammer
Pencil
Wire Brush
Level
Safety Glasses
Rally and Traditional Picnic Tables using the A2374 Kit
7/16"Wrench
Masonry Drill Bit Set
1/8" and 1/4"
Optional: (4) 1/4"
Rubber Washers
90130A027
(4) 1/4" x 3.25" 18-8
Stainless Steel Stud Anchors
92188A102
(2) Surface Mount
Mounting Brackets
Instructions apply to all Picnic Tables with a 1.66" OD steel tube.
Installation Instructions
Step-by-Step Installation Sequence
1.
2.
3.
5.
4.
Evacuate debris from mounting holes using compressed air and a steel wire
brush. This will create a clean environment for the anchor system.
!
2
Locate an anchor and adjust the nut so it is ush with the top of the anchor to
protect the threads from being damaged. Insert the anchor into the hole.
Use the hammer to x the anchor into the drilled hole by giving it several
hammer blows.
6.
7.
Repeat steps 2 - 5 until all anchors are installed.
8.
!
Place table in the desired location. Mark the location of the holes with a
pencil. To verify the alignment of the anchor markings you may reference
page 3.
5
4
Remove the nuts and washers o of the anchors. Place the table frame so
it is centered between two anchors on both sides. Reference image 9 at the
bottom of the page for additional clarity. The brackets line up with the vertical
tubing, but on opposite sides to prevent any kind of movement.
Care should be given to avoid rubbing the powder coating o the
bracket. A 1/4" rubber washer is a suitable replacement option. Mount the
table to the ground by placing a washer and a nut onto each anchor. Leave
the hardware nger tight until all of them have been installed. Verify that the
bench is level before tightening the anchors. Tighten all of the hardware with
a 7/16" wrench.
It is recommended that you start holes in sequential order from the
smaller to the larger drill bits to avoid oversized holes or holes drilled too
deep. Begin with a 1/8" diameter drill bit followed by a 1/4" diameter bit.
Rally and Traditional Picnic Tables using the A2374 Kit
7
9
8b8a
Shape of table may vary
Copyright 2019 ANOV Manufactured in the U.S.
Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.
Installation Instructions
FOOT MOUNTS:
02/07/2019
Rally and Traditional Picnic Tables using the A2374 Kit
SECTION A-A
SCALE 1 / 22
A A
1
1
2
2
A A
B B
1
001
OF
F2114
1
REV
SHEET1 / 22
SCALE
DATE 4/17/2018
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X 1 X.X .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX .015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 01/21/18
3.25
(2 PLCS)
14.38
.2
5
(4
PLCS)
35.57
SECTION A-A
SCALE 1/18
A A
1
1
2
2
A A
B B
1
001
OF
F1113
1
REV
SHEET1/18
SCALE
DATE 2/6/2019
DWG NO
TITLE
A
DRAWN D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90
UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125
.0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X 1 X.X .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX .015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 01/21/18
33.84
23.95
3.25
(2 PLCS)
.25
SECTION A-A
SCALE 1/15
A A
1
1
2
2
A A
B B
1
001
OF
D2006
1
REV
SHEET1/15
SCALE
DATE
2/6/2019
DWG NO
TITLE
A
DRAWN
D. METZ
SIZE
ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES
OR BENDS ARE 90 UNLESS OTHERWISE SPECIFIED
DO NOT SCALE DRAWING
PRINT IS FOR FABRICATION ONLY. ALL SURFACES
MAY EXPAND BY .125 .0625 DURING COATING.
TOLERANCES UNLESS NOTED:
X 1 X.X .5 X.XX ± .25 X.XXX ± .125
X.XXXX ± .0625 X.XXXXX ± .03125
X.XXXXXX .015625 ANGULAR ± 1°
211 North Lindbergh Blvd.
St. Louis, MO 63141
888.535.5005 tel
314.754.0835 fax
specify@anovafurnishings.com
anovafurnishings.com
THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF
ANOVA. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.
THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.
THIRD ANGLE PROJECTION
NOTES:
THIS DRAWING IS FOR PROTOTYPE OR TOOLING
USE ONLY. DO NOT USE FOR PRODUCTION.
REV DESCRIPTION ECN TR.# DATE
001 01/21/18
53.91
3.25
(2 PLCS)
13.72
.25
(4 PLCS)
FOOT MOUNT CHART
FOOT MOUNT 1
Sku #s Length Width
D2006 53.91" 13.27"
F1152 70.25" 13.27"
FOOT MOUNT 3
D1111
D1113
D6013
D6013COM
F1111
F1113
F1117
F1118
L1111
L1121
33.84" 23.95"
D1110
F1110
33.40" 24.29"
FOOT MOUNT 3
Length
Width
3.25"
(2 PLCS)
Ø.25"
Length
Ø.25"
(4 PLCS)
Width
3.25"
(2 PLCS)
35.57"
3.25"
(2 PLCS)
Ø.25"
(4 PLCS)
FOOT MOUNT 1 F2114 - FOOT MOUNT
14.38"
  • Page 1 1
  • Page 2 2
  • Page 3 3

Anova D6013 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI