Anova PLAC2424A Assembly Instruction

Brand: Anova

Model: PLAC2424A

Type: Assembly Instruction

800.231.137

[email protected]

Assembly Instructions

Planter Lier "Riser" Kit

COMPONENT PARTS:

RECOMMENDED TOOLS:

Level

ASSEMBLY:

Determine if the risers are needed. The risers are intended to help level the planter on uneven

surfaces and bump sides higher than others (up to 3/4") to account for imperfections in

installation location. Use a level to determine what locations on the bottom of the planter will

need to be risen.

2. Remove the label from the adhesive pad and stick the

planter riser to the planter bottom in the desired location.

4. If more than one riser in one location is necessary, use the

adhesive pad to adhere multiple risers together.

Planter Riser

• Furniture must not be used other than for its intended purpose and should be inspected regularly for loose,

missing, or broken hardware, and general instability

• Furniture that is damaged or appears to be unstable must be removed from service and repaired or replaced

• Repairs must be made using only factory authorized parts and methods.

WARNING

• Do not drag the assembled unit across any surface.

• This product requires only periodic cleaning with a sponge and a solution of mild detergent and water to remove

surface dirt. Do not clean with a solvent or petroleum based products.

CARE AND

MAINTENANCE

Note: Please contact Customer Care at 1-866-797-1761 when ordering replacement parts.

2.00

.75

THIS DRAWING IS FOR PROTOTYPE OR TOOLING

USE ONLY. DO NOT USE FOR PRODUCTION.

NOTES:

MATERIAL: A356F ALUMINUM. APPROXIMATE CASTING WEIGHT: lbs

PART VOLUME XX.XXX CU. IN.

0.0625" RADIUS ON ALL INSIDE AND OUTSIDE CORNER UNLESS

OTHERWISE SPECIFIED

PARTING LINE SHALL BE SMOOTH AND BLENDED WITHOUT

EVIDENCE OF PARTING LINE LEDGE, GATE LOCATION, PARTING

LINES ARE SUBJECT TO ANOVAS APPROVAL.

CASTING MUST HAVE A NORMAL NON-FERROUS SAND CASTING

FINISH THAT IS FREE OF VOIDS, SCRATCHES, SPLITS, DEFORMATION,

SINK MARKS OR CRACKS. - RMS 300 - 560

DEGAS FOR POWDER COATING

THE THREE-DIMENSIONAL SOLID MODEL (SOLIDWORKS) IS THE

MASTER DEFINITION OF THE PART.

THIS TWO-DIMENSIONAL DATA IS PROVIDED FOR INSPECTION AND

REFERENCE PURPOSES ONLY.

ONLY CRITICAL DIMENSIONS ARE BEING SHOWN ON THIS

DRAWING. THESE DIMENSION ARE CRITICAL IN THE ASSEMBLY AND

PERFORMANCE OF THE PART.

THE MANUFACTURING PROCESS SHOULD IMPLEMENT THE

10.

NECESSARY PROCESS CONTROL TO REDUCE TOLERANCE AND

VARIATION FROM THE NOMINAL DIMENSION.

STANDARD NOTES

VIEWS FOR PAGE 1

SIDE VIEW WITH ALL HEIGHT AND WIDTH DIMS CALLED OUT

TOP AND BOTTOM VIEWS WITH OVERALL DIMS

FRONT VIEW WITH OVERALL DEPTH DIMS AND LEG ANGLES IF

NEEDED

SIDE VIEW WITH ALL ANGLES CALLED OUT

ISO VIEW IN "SHADED WITH EDGES". NO DIMS NEEDED

ADD WEIGHT TO NOTE 1

REVISIONS

REV.

DESCRIPTION

ECN TR #

DESIGNER

DATE

001

ORIGINAL PRINT

NONE

001

riser

SHEET 1 OF 1

2:1

4/14/2022

REV

DWG. NO.

SIZE

TITLE:

PRINT IS FOR FABRICATION ONLY. ALL SURFACES

MAY EXPAND BY .125± .0625 DURING COATING.

ALL DIMENSIONS ARE IN INCHES AND ALL ANGLES

OR BENDS ARE 90º UNLESS OTHERWISE SPECIFIED

DO NOT SCALE DRAWING

211 North Lindbergh Blvd.

St. Louis, MO 63141

888.535.5005 tel

314.754.0835 fax

[email protected]

anovafurnishings.com

THIS DRAWING AND ALL THE INFORMATION CONTAINED HEREIN IS THE PROPERTY OF

ANOVA™. DO NOT USE OR COPY WITHOUT WRITTEN PERMISSION.

THIS DRAWING IS CONFIDENTIAL AND IS SUBJECT TO RETURN ON DEMAND.

THIRD ANGLE PROJECTION

DRAWN

DATE

r. Patterson

TOLERANCES UNLESS NOTED:

X ± 1 X.X ± .5 X.XX ± .25 X.XXX ± .125

X.XXXX ± .0625 X.XXXXX ± .03125

X.XXXXXX ± .015625 ANGULAR ± 1°

A A

B B

SCALE

NOTE: It is recommended that there be 10" - 12" of space between the risers.

Planter Riser with Adhesive

36" Round Planter

Planter Risers with Adhesives

48" Rectangular Planter

Planter Riser Dimensions

Anova PLAC2424A Assembly Instruction

Anova PLAC2424A Assembly Instruction

Anova PLAC2424A Assembly Instruction

Related papers

Other documents