Page is loading ...
Creative Furniture
G17ML52022-08
【Shelf】
Instructions for Use
1 2
Safety Instructions (Make sure to follow these instructions)
Caution
Do not handle roughly, or use improperly. Failure to follow the safety precautions
cause injury or damage to the product may.
Caution
Installation
Many chemical substances will be released by the product when it is first purchased. Sufficiently
ventilate or expose the product to moving air for some time after purchasing it.
Do not completely close windows when using the product in rooms with conspicuously high
temperatures/ humidity (the benchmarks for these are temperatures in excess of 28 C (82.4 F) and
relative humidity in excess of 50%).
Appropriate Ventilation Measures
Do not use this shelf as
a step stool.
Do not stand on or lean
to this product. Failure
may cause you to fall
and get injured.
Do not reconfigure.
This leads to malfunction or accident.
Reconfiguring by yourself causes the product
to malfunction or accident. Okamura will
have no responsibility for any disadvantages
caused by remodeling.
If you need remodeling, contact our official
dealers beforehand.
Do not attempt to disassemble or repair the
product yourself. Please contact our official
dealers when needed.
If found any loose bolts or screws, do not use
the product. Failure may cause damage to
the product and result in injury.
Do not put your fingers or hands into the spaces
of the product. This may lead to injuries.
Pay attention to the following when
moving or housing the shelf units for
layout change, etc.
Two or more persons shall be assigned to
hold and move the body.
When you change the layout, make sure to
contact the retail outlet where you purchased
the product or our official dealers since the
product may not be able to stand by itself
depending on the layout.
Do not hang on to the frame, panel, etc. of
the product. Failure may cause damage to
the product resulting in injury.
Do not apply excessive power from the inside
or outside to the panel. Failure may cause
damage to the product.
Loading part Maximum loading capacity
Worktop,
Shelf
30kg(66 lb)
(uniformly distributed weight)
Hanger Pipe 30 kg (15 hangers)
Do not hang anything other than clothes on the
hanger pipe. Failure may cause injury or damage.
What is Uniformly distributed weight ?
It means to load on a work surface, etc. evenly.
Uneven loading on the product may cause
balance loss and thus drop or fall.
Do not handle roughly, or use improperly.
Failure to follow the safety precautions
cause injury or damage to the product.may
Do not disassemble or repair on your own.
Do not load anything more than the maximum
loading capacity of the product. It may cause
you to fall or damage to the product.
Do not place on uneven floor.
Indoor use only. Avoid direct sunlight
No outdoor or waterfront use.
Avoid places directly exposed to heat or
wind from stoves or air conditioners. Failure
may cause deformation or discoloration.
When placing alongside windows, use
curtains or blinds to avoid direct sunlight.
Make sure to place the product on an even
floor when using. Failure may cause the
product to deform or to be damaged.
Please follow instructions below. Failure may cause serious damage to the product and
Okamura will have no responsibility for any damages.
Avoid places with high temperature, high
humidity, and extreme dryness. Failure may
cause deformation, discoloration, and mold.
If the plate surface is exposed to heat or
wind, the ink may dry out or dust may easily
adhere to it, making it difficult for the ink to
be removed.
3 4
Parts Name Operation Guide
Option
Wiring hole
Leveler Leveler
Work top
Frame
Shelf
Wiring hole
Frame
Shelf
Shelf Unit
Monitor unit
whiteboard unit Coat hanger unit
Wiring hole
Leveler
Frame
Shelf
Wiring hole
Leveler
Frame
Shelf
Wiring hole
Leveler
Frame
Shelf
Hanger pipe Bracket
Back panel
Back panel
End panel
Back panel
Gate
Plant
box
Wiring cover
Whiteboard
LowerHigher
Leveler
Frame
Shelf
Hanger pipe
>0RXQWLQJSLWFK@
+RUL]RQWDOPP
9HUWLFDOPP
3LWFK
Leveler operation
The product height can be adjusted within the
range of 0 to 20 mm by rotating the Levelers at the
bottom of the body. When installing the product,
operate the four Levelers to keep it horizontal.
Be sure to perform height adjustment with
more than two people using extreme caution
so as to prevent your hands and fingers from
getting caught.
Caution
Coat hanger unit
Be careful not to cause the hangers to cluster on
one side. Failure may cause the hanger pipe to
be distorted. The number of hangers shows just
a rough standard. It may vary depending on the
type of hanger and clothing used. No hangers are
supplied with the unit. Please prepare hangers to
use.
Monitor unit
Please procure the monitor and its mounting
screws by yourself. Please check the instruction
manual of the monitor in advance for the possibility
of mounting and the necessary screws.
Compatible monitor
The mounting pitch should be correct (see the figure
on the right).
The back of the monitor should be flat without any
protrusions.
Compatible size
<1200W monitor unit>
50-inch 40 kg or less
External dimension W1155xH795xD100 or less
<900W monitor unit>
32-inch 40 kg or less
External dimension W858xH795xD100 or less
5 6
Operation Guide Operation Guide
Screws designated by
the monitor manufacturer
Screws supplied with
mounting brackets
Monitor
Curing
Monitor mounting
bracket (A)
Monitor mounting
bracket (C)
Monitor mounting
bracket (B)
Monitor mounting
bracket (B)
Monitor mounting
bracket (C)
Bracket
Monitor
Screws designated by
the monitor manufacturer
Screws supplied with
mounting brackets
Monitor
Curing
Monitor mounting
bracket (A)
Monitor mounting
bracket (C)
Monitor mounting
bracket (B)
Monitor mounting
bracket (B)
Monitor mounting
bracket (C)
Bracket
Monitor
Shelf (lowest)
Power tap
Plug
Wiring Cap
Wiring hole
Wiring Cap
Cord
Power tap
Plug
Wiring Cap
Wiring hole
Wiring Cap
Power tap
Cord clip
Power tap
Cord clip
Wiring cover
Option
How to attach/detach the monitor
Place a soft material such as a
protective sheet underneath.
Fix the mounting bracket (A) to
the back of the monitor.
Prepare the screws specified by
the monitor manufacturer.
Attach the mounting brackets
(B) a n d (C) t o t h e m o u n t i n g
bracket (A) using the screws
supplied with those brackets.
Hook the monitor mounting brackets (B) and (C) on the fall stopper bracket.
Be sure to have two or more people attach/detach the monitor.
Wiring
In case of an office floor, wires can be raised from the
lower portion of the frame unit. Install a power tap in
advance.
[Wiring procedure]
Remove the lowest shelf.
Fully push the wiring cap into the wiring hole so
that the hole will be open. Insert your plug into the
power tap installed inside.
Pass the cord extending from the
plug into the wiring hole. Make
sure the plug is firmly inserted
into the tap.
Re-attach the shelf.
When lowering the shelf, be careful not to have your
fingers caught between the shelf and the frame.
Caution
When lowering the shelf, be careful not to damage the cord.
Failure may damage the cord to cause a fire or electric shock.
Caution
For the monitor unit, use the supplied cord clips to
hold the cables along the frame if necessary.
The back of the clips is provided with
doubles-side adhesive tape.
When using the optional wiring cover, pass the
cables along the frame in the same way. The back
of the wiring cover is magnetic.
Caution
Do not insert any metal objects (hairpins, wires, etc.) into the
power tap outlets. Failure may cause a fire or electric shock.
Do not pull any installed cables. Failure may cause a
contact failure or fire.
Caution
7 8
Operation Guide
Please follow instructions below. Failure may cause serious damage to the product and
Okamura will have no responsibility for any damages.
Operating Precautions and Maintenance
Instructions to Extend the Life of Product
Planter box
front
board
Planter box
Planter box
Planter box (option)
The planter box does not come with any plants.
Use our Interior Green Small-Pot Series products available separately or your
prepared artificial plants.
For this product, we recommend artificial plants.
If water is splashed onto the body, immediately wipe it off with a dry, soft cloth.
If the body is left wet for a long time, it may rust.
[Removing the front board]
Hold and lift the front board by both hands.
While rotating and pulling the lower portion of
the front board toward you, remove the board.
Put plants in the planter box.
When re-attaching the front board, carry out
the above steps and in the reverse order.
Whiteboard marker
Please use dedicated whiteboard markers
to write on the whiteboard surface. Ease
of writing will vary depending on the
combination of whiteboard, marker, and
eraser. We suggest using the products
recommended in our catalog.
If you erase your writing immediately
afterwards, ink residue may remain. We
recommend erasing after about 10 seconds,
when the release agent (an ingredient that
makes it easier to remove the ink) has settled.
If the marker is stored in a vertical position,
the components may shift and make it
difficult to erase. Be sure to shut the cap tight
and store it horizontally.
Whiteboard
Please note that contact with sharp or hard
objects may damage the surface finish. Also,
please avoid using tape or other adhesive
material on the board surface.
Due to the properties of the marker,
transparent outlines may remain. Also, if any
writing is left on the board surface for 3 days
or more, it may become difficult to erase. In
such cases, wipe it with a damp cloth that
has been wrung out tightly, and dry wipe
afterwards.
Eraser
The eraser should be replaced when it wears
out. If the eraser becomes difficult to clean
or if it is damaged, please replace it. We also
recommend regular replacement.
If the product has become unsteady due to
loosening of the bolts or screws during use,
retighten them immediately.
Do not use any sharp edged objects such as
a knife on the worktop. Failure may damage
the worktop.
Avoid direct exposure to steam. Failure will
cause rust.
Wipe off any water on the product with a dry
and soft cloth.
Immediately wipe off tea, coffee, detergent,
chemical, etc. if any spilled.
This instruction manual is very important, so
store it in an easily accessible location.
Regular maintenance is recommended for
long-life use. Make your request to us early
for inspections and repairs (fees required)
when the warranty period has expired.
9 10
Whiteboard Surface
Materials and Surface Finish
For daily care
Instructions to Extend the Life of Product
Shelf Unit
Part Materials Surface Finish
Structure
Frame Steel Amino-alkyd resin
coating or polyester coating
Wiring Cap polypropylene
Worktop,
Shelf
Core material Steel
Surface materials Melamine resin
Coaming ABS resin
Back panel (Cort hanger and
Monitor unit) Steel Amino-alkyd resin
coating or polyester coating
Hanger Pipe (Cort hanger) Steel Plating (Chrome)
Back panel
(Option)
Surface materials Polyester
Core material Plywood
Mounting bracket Steel Amino-alkyd resin
coating or polyester coating
Whiteboard
Surface materials Steel White board coating
Core material Laminated wood,
styrofoam (polystyrene)
Gate , Plant box , End panel , Wiring cover
Part Materials Surface Finish
Structure Body Steel Amino-alkyd resin
coating or polyester coating
Please understand that product specifications might change without prior notification due to improvements
madeto the pr oduct.
Wipe off with a dry soft clean cloth.
If dirt is noticeable, wipe it off with a well
wrung soft cloth moistened with thin neutral
detergent. Be sure to remove detergent
completely with a damp cloth and wipe again
with a dry cloth to dry it.
Caution
Do not leave any water on the worktop.
Do not use a chemical cloth or an organic
solvent such as thinner and benzene. Please
note that the product with its color or texture
deteriorated cannot be restored to its original
state.
Wipe with a well wrung soft cloth moistened.
If dirt is noticeable, wipe it off with a well
wrung soft cloth moistened with thin neutral
detergent. Be sure to remove detergent
completely with a damp cloth and wipe again
with a dry cloth to dry it.
Steel part , Worktop Resin part
D o not use polishing powder
or scrubbing brush to clean,
as it will damage the surface
finish.
If it is difficult to clean the surface,
wipe it with a damp cloth that has been
wrung out tightly. Afterwards, dry wipe
with a soft, fine-grained cloth.
Please avoid cleaning with detergent
etc. as it may cause dirt to adhere.
Also, never wipe with organic solvents
such as benzine or thinners.
/
