Page is loading ...
Hermetic Camera AP-143G
AP-143G VIZIT
SAFETY INSTRUCTIONS
PARTS LIST
INSTALLATION
OPERATING INSTRUCTION
–
.
1
1
1.
*
is a dome colour camera for outdoor surveillance intended for use in video doorphones and access
control systems.
In order to protect the camera, avoid placing or using the product under direct sunlight.
Please ensure that the input voltage range is within the specifications
Do not attempt to service the camera by yourself. Please refer all services to qualified service personnel.
Camera pc.
Operating instruction pc.
Fastening kit pc
Choose the camera location with regard to the required field of view. See Fig. 3 for the best camera location and its
field of view.
···
Figure 1 - Hermetic Camera AP-143G
······
Metal case, vandal-proof
Weather-resistant
Wide range of operating temperatures
24 InfraRed LEDs for illumination
Illumination auto ON in dark environment
Colour image auto switch to B/W in dark environment
1.
2.
3.
.
4.
5.
2 -
Remove the mounting base by loosening two locking
screws (5) with the hex-nut wrench supplied.
Choose location* for the camera on a wall or the ceiling,
and attach the mounting base securely with screws
and concrete inserts supplied
Connect the camera to your monitor and power supply
unit. Check if the monitor shows picture from the camera.
To adjust the picture, set the ball camera to the suitable
position by rotating the ball and middle cover.
Fix the ball camera securely by fastening the locking
screws.
Figure Camera Installation
(1)
(6)
(7) .
Attach the locking cover (4), ball camera (2) and middle
cover (3) to the mounting base. Fasten the locking
screws so that with locking and middle covers fixed, the
ball be loose enough to rotate
1
2
3
4
5
6
7
Red
Black
Yellow
Black
CONNECTIONS
1. Connecting the AP-143G camera to VIZIT individual video doorphones.
Caution Ev
VIZIT
Connect the camera wires directly to the corresponding terminals of your VIZIT monitor or commutator BKM-440.
Do not connect the camera wires to the terminal of the doorstation.
See an example of connecting two cameras to the individual doorphone on Fig. 5.
!
-
-
Camera altitude above the floor m
Distance from the center of the entrance
door = m horizontal
Figure Camera field of view
= 2.5
1.5 ( )
3 -
0
0.5 m
1.5 m
2.5 m
Door
yellow VO (video out)-
black VGND video ground-( )
black GND ground-()
red Ec supply voltage for camera-( )
Figure Wires, their colour and destination4 -
Figure Two cameras AP-143G with monitor VIZIT-M430C
in individual video doorphone
5 -
-18
+18
+12
-12
4
3
1
2
2
1
1
2
12
1
3
4
12
2
1
2
2
1
V
1A
50
COLOUR
LINE
GND
+E
Ev
Ec
LC
Doorstation
BVD 403A-
Power Supply
BPD18/12-1-1
R 10 )
ELECTROMECHANICAL
LOCK ( Ohm
Camera
AP-143G
LN
GND
LN+
VI1
+E
DATA
Ec1
Ec2
GND
VI2
- 430
Monitor
VIZIT M C
yellow
black
red
yellow
black
red
Camera
AP-143G
3
1
2
3
1
2
3
1
2
21 3
Connect two black wires of the
camera to each other.
black black
If the length of the cable connecting your monitor and the camera exceeds 20 m, use a coax or composite cable
specially designed for video surveillance systems. This will considerably reduce possible image distortion.
2. Connecting the AP-143G camera to VIZIT multi-apartment video doorphones.
456
2TM
3 SP
5 MIC
1 GND
4 +E
6 DSD
12365
4123
RX
SP-
TX
+DL
-DL
OP
TM
SP+
GND
MIC
+E
DSD
Doorstation
-311 )BVD (R
Control Unit
-302 МBUD ( )
Camera
AP-143G
yellow
black
red
1
2GND
+12V
Power Supply
BPD12-1-1
1
2
VIDEO
(to commutators B
)
K-4MV, BK-4V, or
distribution amplifiers RVS-4
Figure Camera in multi-apartment video doorphone6 - AP-143G
Model AP-143G
Colour system
Image sensor
Effective pixels
Horizontal H x vertical V()
Horizontal resolution
Lens
Angle of view diagonal vertical / horizontal( / ),°
Infrared LED
Infrared LED range
Sensitivity
Scanning system
Video output
Power supply
Current consumption
Dimensions (diameter x height)
Weight
Ingress protection
Operating temperature
PAL
1/ " SONY4
5 (H) x 5 (V)37 97
420 TVL
f = . Board2 8 mm,
78 1 68/ 5 /
24 LEDs
15 m
0( )Lux Infrared LEDs on
625 TVL fps, 25
1 / 75 , compositeVp-p Ohm
12VDC ± 10%
20мА6 max.
94 х 68.5 mm
650 g
IP 66
- 30° C …+ 50° C
SPECIFICATIONS
Connect the GND
terminals of Power Supply
and Control Unit
black
/