Page is loading ...
1
Style A
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
TP200 20-42-FO-00012 Rev A1 C2169
Applies to Models:
Dental TS Casework
Special Tools:
3/8” masonry drill bit
9/32” wood drill bit
Hammer drill
Language of origin: English
003-10102-00 Rev. AA3 (9/4/2018)
Synthesis
®
Casework - Treatment Station
Setup Instructions
Note
This Midmark casework unit must be connected to a dedicated circuit rated 20 A, 120 VAC.
Failure to comply could result in an overload of the electrical circuit and/or components. All
electrical and plumbing connections must be made by a licensed electrician and plumbing
contractor following applicable local, city, and national codes.
Midmark casework unit contains six electrical duplex outlets, which are rated at a combined 15 amps.
This rating must be taken into account when plugging device(s) into the available outlets.
This Midmark casework unit may contain materials with a smoke Index (SDI) of 400.
Note
Inspect all components for shipping damages. A concealed damage report must be
filed with the carrier (by the person receiving the goods) within 5 days of delivery.
midmark.com
2
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Model Number
Midmark uses a product part number for the cabinets that has a detailed structure.
Step 1
Step 2
Step 3
Step 3
Step 4
Step 5
Step 5
Step 6
Step 7
Step 8
Step 10
Step 9
midmark.com
3
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Note
Full size Floor Template and Wall Template are available upon
request, or refer to rough-in dimensions on next page.
Wall
Front
Air Supply
Vacuum Supply
Water Supply
25/32”
(1.9 cm)
43 - 9/16”
(110.7 cm)
42”
(106.7 cm)
21 - 13/16”
(55.4 cm)
22 - 19/32”
(57.4 cm)
1/2” (1.3 cm) NPT
2.5” (6.4 cm)
(max.)
2” (5.1 cm)
(min.)
2.5” (6.4 cm)
(max.)
2” (5.1 cm)
(min.)
5.8” (1.6 cm)
O.D.
Floor
Floor
Electrical
Terminal
Box
Electrical
Supply
Secure Terminal Box to cabinet
after electrical supply is connected
120 VAC / 20 Amp / 60 Cycle
3-wire, Dedicated Circuit
Left Side Plumbing
Rough-In Perimeter
Right Side Plumbing
Rough-In Perimeter
11 - 7/8”
(30.2 cm)
2 - 15/16”
(7.5 cm)
11 - 7/8”
(30.2 cm)
10 - 3/8”
(26.4 cm)
1”
(2.5 cm)
2 - 1/4”
(5.7 cm)
7 - 5/16”
(44 cm)
2 - 1/4”
(5.7 cm)
Floor Layout (as applicable)
Have licensed electrical and plumbing contractors position and
install electrical outlet receptacles and related plumbing using
the pre-installation template or layout.
Note: Be sure floor construction is sufficient to adequately support / anchor the
casework unit. If necessary, contact a licensed contractor to reinforce the floor.
midmark.com
4
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Wall Layout (as applicable)
Floor
30 - 1/2”
(77.5 cm)
Right Side Plumbing
Rough-In Perimeter
Right Side Plumbing
Rough-In Perimeter
Left Side Plumbing
Rough-In Perimeter
Left Side Plumbing
Rough-In Perimeter
Center Side Plumbing
Rough-In Perimeter
Center Side Plumbing
Rough-In Perimeter
43 - 9/16”
(110.7 cm)
42”
(106.7 cm)
25/32”
(1.9 cm)
3 - 1/8”
(7.9 cm)
9 - 3/4”
(24.8 cm)
9 - 3/4”
(24.8 cm)
9 - 3/4”
(24.8 cm)
3 - 1/4”
(8.3 cm)
3 - 1/4”
(8.3 cm)
20 - 3/4”
(57.7 cm)
7 - 5/8”
(19.4 cm)
3 - 3/4”
(9.5 cm)
5/8”
(1.6 cm)
Note
These panels are only here if the
side storage is selected.
midmark.com
English-5
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 3:
Remove cabinet floors.
Note: Optional floor must be removed if door is present.
Step 1:
Remove bottom drawers (2) from cabinet.
Note: If needed remove 2” drawer as shown.
Step 4:
Remove bolts (4), washers (4), and screws (8) out of
shipping brackets (2).
Step 2:
Remove doors (2) from base as required.
Option
midmark.com
English-8
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 9:
Loosely install mounting hardware and anchor into floor.
Step 8: Concrete Floor
Use 3/8” masonry drill bit to drill 2” deep holes into concrete.
Step 10:
Level cabinet by using leveling feet on base of cabinet.
Use shims when necessary. Do Not adjust feet more than
1/2” (1.3 cm).
Step 8: Non-Concrete Floor
Use 9/32” wood drill bit to drill holes into non-concrete.
Sub-base
3/8” drill bit
3/8” diameter
Anchor
Mounting Clip
2”
(5.1 cm)
Concrete
Sub-base
9/32” drill bit
9/32” diameter
Anchor
Mounting Clip
Non-Concrete
Concrete
Non-Concrete
1/2” (1.3 cm)
Away from
Floor
Closer to
Floor
Shim
midmark.com
English-9
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 13:
Install base doors as required.
Step 11:
Tighten hardware to secure anchor. Trim excess shim.
Step 14:
Install drawers (2) into base cabinet.
Step 12:
Install cabinet floors as required.
Note: Optional floor will need installed if door is present.
Excess
Shim
Option
midmark.com
English-10
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 17:
Remove doors from upper unit.
Step 15:
Remove side panels (2) and electrical covers (2) by remov-
ing screws (4) from covers.
Step 18:
Remove shelves from upper unit.
Step 16:
Locate upper unit and task light cover.
Screws
Cover
Side
Panel
Side
Panel
Cover
Screws
Task
Light
Cover
Upper
Unit
Hinge
midmark.com
English-11
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 19: Attaching Additional Units
Place upper unit onto base and secure with screws (16)
as shown.
Note
For ease of installation screws can be started in
midsection panel before placing unit onto base.
Upper Unit
Base Unit
Midsection
Panel
Note
For ease of installation screws can be started in
midsection panel before placing unit onto base.
midmark.com
English-12
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 22:
Install electrical covers (2) with screws (4) and install side
panels (2).
Step 20:
Insert shelf clips (4) per shelf and instal shelves.
Step 23:
Install handles with screws (2) as needed. Place adhesive
covers over screw heads inside of drawers.
Step 21:
Install upper unit doors.
Screws
Cover
Side
Panel
Side
Panel
Cover
Screws
Adhesive
Covers
Shelf
Clips
Hinge
midmark.com
English-13
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 25: Task Light Cover
Install task light cover by first sliding corner and side of cover into posi-
tion and lift and slide other side into place.
Step 24a:
Install Clock / Timer into cabinet with rubber ring. If desired plug into
top of base cabinet under upper unit.
Note: Is not required to use plug to power Clock / Timer.
Step 26: Task Light Half Cover
Install half task light cover by first sliding corner and side of cover into position
and lift and slide other side into place.
Back of
Clock / Timer
Task
Light
Cover
Step 24b: Optional Plug-in spot
Plug-in at inside base cabinet outlet and run wiring from bottom
of cabinet up through to Clock / Timer.
Note: Is not required to use plug to power Clock / Timer.
Rubber
Ring
Base
Cabinet
Upper
Unit
Half Task
Light Cover
midmark.com
English-14
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Screws
Bracket
Step 28: Optional
Remove screws (2) from tub bracket, slide bracket and tub toward
opening and move up or down. Make sure to slide back of bracket into
side panel of cabinet and secure with screws (2).
Step 29: Optional
Remove pull-out shelf from cabinet.
Step 27: Optional
Remove screws (2) from shelf bracket, slide bracket and shelf toward
opening and move up or down. Make sure to slide back of bracket into
side panel of cabinet and secure with screws (2).
Screws
Bracket
Step 30: Optional
Remove screws (2) from brackets, move bracket up or down and slide back of
bracket into side panel of cabinet before securing bracket. Reinstall shelf.
Bracket
midmark.com
English-15
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00 [Rev 9/4/18]
TP200 20-42-FO-00012 Rev A1 C2169
Door Adjustment Up and Down
Turn cam screw located in center of mounting plate to
adjust door position up or down (+ or - 2 mm).
Door Adjustment Away or Closer
Turn Spiral Tech cam screw located furthest from door
to position the door farther from or closer to cabinet
(+3 mm or -2 mm).
Door Adjustment Side to Side
Turn screw located closest to door to increase or decrease
the door overlay side to side (+ or - 2 mm).
Left
Right
Down
Up
In
Out
Door Adjustment
Step 31:
Adjust doors as necessary to prevent damages to doors while in use.
Turning off/on Soft-Close Door Hinge
Push switch toward hinge plate and close door once to
turn off soft-closing hinge. Reactivate Soft-close hinge
pushing switch towards door handle.
On
2
1
midmark.com
English-16
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
BK
GN
WH
YL/GN
BK
GN
WH
YL/GN
GN
BK
GN
WH
BK
WH
Floor
Holes in
Base
Step 32:
Remove floor from base cabinet. Secure the electrical box to inside of
cabinet with (#10 x 3/8”) screws (2) using any holes needed. Reinstall
floor into base.
Note
Only Licensed Electricians following local
and applicable electrical codes should
install and connect the electrical supply power.
Midmark cannot be held responsible for
installations that do not conform to local codes.
Equipment Alert
Dedicated branch circuit rated at
120VAC, 50/60 Hz, 20 amp.
Item Color
(English)
BK Black
GN Green or Green / Yellow
WH White
midmark.com
English-17
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
BK
GN
WH
YL/GN
BK
GN
YL/GN
GN
WH
WH
WH
BK
BK
GN
GN
WH
GN
WH
BK
GN
GN
WH
BK
GN
BK
BK
BK
WHBK
GN
Floor
Holes in
Base
Step 32:
Remove floor from base cabinet. Secure the electrical box to inside of
cabinet with (#10 x 3/8”) screws (2) using any holes needed. Reinstall
floor into base.
GN
GN
GN
WH
BK
BK
WH
WH
Note
Only Licensed Electricians following local
and applicable electrical codes should
install and connect the electrical supply power.
Midmark cannot be held responsible for
installations that do not conform to local codes.
Equipment Alert
Dedicated branch circuit rated at
120VAC, 50/60 Hz, 20 amp.
Item Color
(English)
BK Black
GN Green or Green / Yellow
WH White
midmark.com
English-18
© 2017 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 |
003-10102-00
TP200 20-42-FO-00012 Rev A1 C2169
Step 32:
Remove floor from base cabinet. Secure the electrical box to inside of
cabinet with (#10 x 3/8”) screws (2) using any holes needed. Reinstall
floor into base.
BK
GN
WH
YL/GN
BK
GN
WH
YL/GN
BK
GN
WH
GN
BK
GN
WH
WH
WH
BK
BK
GN
GN
GN
BK
GN
WH
BK
GN
GN
GN
GN
WH
WH
BK
BK
BK
BK
GN
BK
WH
GN
GN
Floor
Holes in
Base
Note
Only Licensed Electricians following local
and applicable electrical codes should
install and connect the electrical supply power.
Midmark cannot be held responsible for
installations that do not conform to local codes.
Equipment Alert
Dedicated branch circuit rated at
120VAC, 50/60 Hz, 20 amp.
Item Color
(English)
BK Black
GN Green or Green / Yellow
WH White
midmark.com
/
