Skov ECT 920/DCT 920 fans Technical User Guide

Type
Technical User Guide
ECT 920 • DCT 920
Fans
Technical User Guide
604187 • 2021-02-04
English For other language variants of this document we refer to:
Español Para otras variantes del idioma de este documento, visite:
Français Pour les versions dans d'autres langues de ce document veuillez consulter:
http://docs.skov.com/1053
ECT 920 • DCT 920
Technical User Guide 3
Product and Documentation Changes
SKOV A/S reserves the right to change this document and the product herein described without further notice.
In case of doubt, please contact SKOV A/S.
The date of change appears from the front and back pages.
IMPORTANT!
Notes concerning alarm systems
Breakdowns, malfunctions or faulty settings may cause substantial damage and financial losses when regulat-
ing and controlling the climate in a livestock house. It is therefore essential to install a separate, independent
alarm system that monitors the house climate concurrently with the climate and production controller. According
to EU-directive No. 98/58/EU, an alarm system must be installed in all mechanically ventilated houses.
We would like to draw your attention to the fact that the product liability clause of general terms and conditions
of sale and delivery specifies that an alarm system must be installed.
Note
All rights belong to SKOV A/S. No part of this manual may be reproduced in any manner whatsoever without
the expressed written permission of SKOV A/S in each case.
All reasonable efforts have been made to ensure the accuracy of the information contained in this manual.
Should any mistakes or imprecise information occur in spite of this, SKOV A/S would appreciate being noti-
fied thereof.
Irrespective of the above, SKOV A/S shall not accept any liability with regard to loss or damage caused or
alleged to be caused by reliance on any information contained herein.
Copyright by SKOV A/S.
ECT 920 • DCT 920
Technical User Guide
1 Product description........................................................................................................................................5
2 Product survey ...............................................................................................................................................6
3 Mounting guide...............................................................................................................................................7
3.1 Recommended tools.................................................................................................................. 7
3.2 Positioning of fan in the exhaust unit...................................................................................... 8
3.3 Safety distance........................................................................................................................... 8
4 Installation guide ............................................................................................................................................9
4.1 Electrical connection................................................................................................................. 9
4.1.1 Disclaimer at retrofitting fans ....................................................................................................... 9
4.1.2 Cabling in the exhaust unit........................................................................................................... 9
4.2 Adjusting the jumper and connection in the winch motor ..................................................10
4.3 General information about circuit diagrams ......................................................................... 11
4.3.1 Color code.................................................................................................................................. 11
4.3.2 Power supply isolator................................................................................................................. 11
4.3.3 Letter Code ................................................................................................................................ 11
4.4 Cable plans and circuit diagrams........................................................................................... 12
4.4.1 DCT 920-1 ON/OFF 400 V ........................................................................................................ 12
4.4.1.1 Cable plan.................................................................................................................................. 12
4.4.1.2 Terminals in DCT 920-1............................................................................................................. 12
4.4.1.3 Circuit diagram........................................................................................................................... 13
4.4.2 ECT 920-1E EC stepless - ON/OFF 230 V................................................................................ 14
4.4.2.1 Cable plan ON/OFF ................................................................................................................... 14
4.4.2.2 Terminals in ECT 920-1E........................................................................................................... 14
4.4.2.3 Circuit diagram ON/OFF ............................................................................................................ 15
4.4.2.4 Cable plan stepless.................................................................................................................... 16
4.4.2.5 Terminals in ECT 920-1E........................................................................................................... 16
4.4.2.6 Circuit diagram stepless............................................................................................................. 17
4.4.3 DCT 920-2 ON/OFF 400 V ........................................................................................................ 18
4.4.3.1 Cable plan.................................................................................................................................. 18
4.4.3.2 Terminals in DCT 920-2............................................................................................................. 18
4.4.3.3 Circuit diagram........................................................................................................................... 19
4.4.4 DCT 920-2F VFD 400 V............................................................................................................. 20
4.4.4.1 Cable plan.................................................................................................................................. 20
4.4.4.2 Terminals in DCT 920-2F........................................................................................................... 20
4.4.4.3 Circuit diagram........................................................................................................................... 21
4.4.5 DCT 920-4E EC stepless - ON/OFF 400 V................................................................................ 22
4.4.5.1 Cable plan ON/OFF ................................................................................................................... 22
4.4.5.2 Terminals in DCT 920-4E .......................................................................................................... 22
4.4.5.3 Circuit diagram ON/OFF ............................................................................................................ 23
4.4.5.4 Cable plan stepless.................................................................................................................... 24
4.4.5.5 Terminals in DCT 920-4E .......................................................................................................... 24
4.4.5.6 Circuit diagram stepless............................................................................................................. 25
5 Maintenance instructions ............................................................................................................................26
5.1 Cleaning.................................................................................................................................... 26
5.1.1 Fan............................................................................................................................................. 26
5.2 Recycling/Disposal .................................................................................................................. 26
6 Troubleshooting guide.................................................................................................................................27
7 Technical data...............................................................................................................................................29
7.1 ErP/Ecodesign.......................................................................................................................... 33
ECT 920 • DCT 920
Technical User Guide 5
1 Product description
ECT/DCT fans are supplied with an integrated motor and fan
blades cast in aluminum. ECT/DCT fans are used as ON/OFF fans.
ECT fans can also be used as a Triac regulated fan.
The fan is designed for mounting in exhaust units and wall exhaustion in livestock houses where the ventilation
system operates in the low-pressure range, i.e. in LPV, diffuse livestock houses and Combi-Tunnel livestock
houses.
The fans bear a CE marking and have a sturdy four-point suspension.
ECT 920 • DCT 920
6 Technical User Guide
2 Product survey
409150 DCT 920-1 ON/OFF fan 400V3 50Hz
Three fan blades, 3x400 V fan with aluminium fan blades which fits a duct
with an inside duct dimension of 920mm.
It is used as ON/OFF fan.
High output and good pressure stability.
409152 ECT 920-1E EC stepl. fan 230V1 50/60Hz
Three fan blades, 1x230 V fan with aluminium fan blades which fits a duct
with an inside duct dimension of 920mm. It is equipped with an EC motor
(internal fan speed controller).
It is used as stepless or ON/OFF fan.
High output and good pressure stability.
409153 DCT 920-2 ON/OFF fan 400V3 50Hz
Five fan blades, 3x400 V fan with aluminium fan blades which fits a duct
with an inside duct dimension of 920mm. Special fan blade coating for max-
imum protection.
It is used as ON/OFF fan.
High output and very pressure-stable. It is typically used in special systems
with common duct or the like. High output and noise level must be ex-
pected.
409159 DCT 920-2F VFD fan 400V3 50/60Hz
This product consists of the fan 409153 + a frequency converter.
The frequency controller reduces the power consumption of the individual
fan at partial load.
The frequency converter included is controlled via a 0-10 V signal.
A shielded cable is not used between the motor and the frequency con-
verter, as a sinus filter is incorporated into the frequency converter. The
supply to the frequency converter does not require a shielded cable either.
The distance between the frequency converter and the motor is not limited
to 2 m as is the case when DOL 38 is applied.
409158 DCT 920-4E EC stepl. fan 400V3 50/60Hz
Five fan blades, 3x400 V fan with aluminium fan blades which fits a duct
with an inside duct dimension of 920mm. It is equipped with an EC motor
(internal fan speed controller). Can be used for biological air cleaning as the
fan has a special fan blade coating for maximum protection.
It is used as stepless or ON/OFF fan.
High output and very pressure-stable. It is typically used in special systems
of high standards as regards pressure requirements. High power consump-
tion and noise level must be anticipated at maximum output.
ECT 920 • DCT 920
Technical User Guide 7
3 Mounting guide
3.1 Recommended tools
A list of the recommended tools for mounting purposes can be seen below.
Item Description
Cordless drill
Screwdriver bits
Drill kit
Multimeter
Utility knife
Side cutter
Pointed pliers
Screwdriver
Allen key kit
Ladder
ECT 920 • DCT 920
8 Technical User Guide
3.2 Positioning of fan in the exhaust unit
Place the fan legs in the duct's integrated holes.
The legs are secured in place with cable ties.
Check that the fan is turned correctly and according to
fan type.
Be careful, the fan may rotate if gripped by air flow.
3.3 Safety distance
If the distance from the floor to the fan blade is less than
270cm, mounting a protective mesh in the inlet bell
mouth may be required to meet the statutory require-
ments.
ECT 920 • DCT 920
Technical User Guide 9
4 Installation guide
4.1 Electrical connection
Installation, servicing and troubleshooting of all electrical equipment must be carried out by quali-
fied personnel in compliance with the applicable national and international standard EN 60204-1
and any other EU standards that are applicable in Europe.
The installation of a power supply isolator is required for each motor and power supply to facilitate
voltage-free work on the electrical equipment. The power supply isolator is not included.
4.1.1 Disclaimer at retrofitting fans
In the case of retrofitting fans in an existing house, regardless of ON/OFF or LPC fans, SKOV recommends that
a local expert is involved in checking the electrical installations. The focus should be on cable dimensions, over-
load protections, local transformers, etc. It is of outmost importance to take the fan specifications into account
and, at the same time, ensure that local requirements are fulfilled.
4.1.2 Cabling in the exhaust unit
Drill a hole for the cable and pull it along a leg to the
same side as the winch motor. Seal the hole from the in-
side before the next duct/inlet is mounted.
ECT 920 • DCT 920
10 Technical User Guide
4.2 Adjusting the jumper and connection in the winch motor
Set the jumper on the PCB to give actuator the desired
function.
LED indication
OK = slow flashing
Error = quick flashing (10 times/second)
H1 Actuator controller or +24 V DC supply
H2 Actuator controller
H3 0 V
H6 +24 V DC supply
H7 0-10 V position feedback
H8 0 V
H9 Open collector (transistor output) is used for fan with motor
controller.
H10/11a and H12a relay output is used for fan without motor
controller.
ECT 920 • DCT 920
Technical User Guide 11
4.3 General information about circuit diagrams
Symbols are pursuant to the IEC/EN 60617 standard.
The classification of the symbols ("letter codes") on the symbols is pursuant to the IEC/EN 81346-2 standard.
Reference designations are in accordance with IEC/EN 81346-1:2001 structuring principles and reference des-
ignations. This standard indicates structured methods for naming electrotechnical systems.
4.3.1 Color code
Letter Code Color Standard
BK Black
Color coding on wires are in accor-
dance with standard IEC 60757:
Letter codes to identify colors used
on drawings, diagrams, labelling,
etc.:
BN Brown
RD Red
OG Orange
YE Yellow
GN Green
BU Blue (incl. light blue)
VT Violet (purple red)
GY Grey (slate)
WH White
PK Pink
GD Gold
TQ Turquoise
SR Silver
GNYE Green-and-yellow
4.3.2 Power supply isolator
Power supply isolator
The installation of a power supply isolator is required for each motor and
motor control.
4.3.3 Letter Code
The letter codes used in accordance with standard IEC/EN61346-2.
-F -K -M -Q -S -T -W
Protective
equipment
RCCB / Initial
fuse Protective
motor switch
Controller
Contactor
Fan
Motor
Power supply
isolator
Switch Motor con-
troller
Cable
ECT 920 • DCT 920
12 Technical User Guide
4.4 Cable plans and circuit diagrams
4.4.1 DCT 920-1 ON/OFF 400 V
4.4.1.1 Cable plan
Connection box
4.4.1.2 Terminals in DCT 920-1
ECT 920 • DCT 920
Technical User Guide 13
4.4.1.3 Circuit diagram
Example of terminal
number
For correct connection
see the setup menu
Show connection in
controller
Connection box
ECT 920 • DCT 920
14 Technical User Guide
4.4.2 ECT 920-1E EC stepless - ON/OFF 230 V
4.4.2.1 Cable plan ON/OFF
4.4.2.2 Terminals in ECT 920-1E
ECT 920 • DCT 920
Technical User Guide 15
4.4.2.3 Circuit diagram ON/OFF
Example of terminal number
For correct connection
see the setup menu
Show connection in controller
Winch motor
ECT 920 • DCT 920
16 Technical User Guide
4.4.2.4 Cable plan stepless
4.4.2.5 Terminals in ECT 920-1E
ECT 920 • DCT 920
Technical User Guide 17
4.4.2.6 Circuit diagram stepless
Example of terminal
number
For correct connection
see the setup menu
Show connection in
controller
Winch motor
ECT 920 • DCT 920
18 Technical User Guide
4.4.3 DCT 920-2 ON/OFF 400 V
4.4.3.1 Cable plan
Connection box
4.4.3.2 Terminals in DCT 920-2
ECT 920 • DCT 920
Technical User Guide 19
4.4.3.3 Circuit diagram
Example of terminal number
For correct connection
see the setup menu
Show connection in
controller
Connection box
ECT 920 • DCT 920
20 Technical User Guide
4.4.4 DCT 920-2F VFD 400 V
4.4.4.1 Cable plan
4.4.4.2 Terminals in DCT 920-2F
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36

Skov ECT 920/DCT 920 fans Technical User Guide

Type
Technical User Guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI