Focal Point Seem 1 Louver Recessed FSM1C Installation guide

Brand: Focal Point

Model: Seem 1 Louver Recessed FSM1C

Type: Installation guide

1 of 3

IS0805 REV. A

Seem® 1 Louver

Grid Ceiling | FSM1CG

• Luminaires must be installed by a qualied

electrician (check with local and national

codes for proper installation).

• To prevent electrical shock, disconnect

electrical supply before installation or

servicing.

• Contractor is responsible for adequately

reinforcing walls and/or ceilings to support

xture weight.

• Focal Point, LLC accepts no responsibility

for inadequately reinforced walls and/or

ceilings.

• The information contained in this drawing

is the sole property of Focal Point, LLC.

Any reproduction in part or whole without

the written permission of Focal Point, LLC

is prohibited.

POWER OFF

POWER ON

ATTENTION

SEE ADDITIONAL

INSTRUCTIONS

BEFORE YOU BEGIN COMPONENT KEY

INSTRUCTION KEY

FOCAL POINT SHIPPED INSTALLED

Joiner Screw

(72074)

Joiner Washer

(700158)

Linear Joiner

Bracket

(A37621-01)

Reector Screw

(72026)

(#6x1/4 Self Tapping Screw)

U - Individual

S - Start of Run

I - Intermediate

E - End of Run

SHIPPED IN HARDWARE BAG

2.125"

53.9 mm

2.30"

58.4 mm

lay-in grid spacing tegular grid spacing

Product ID

Label on

Reector

PRODUCT ID LOCATION Flush Lens

Louver

Faceplate

Corner Joiner

Bracket 1

(A39928-03)

Corner Joiner

Bracket 2

(A37621-02)

Corner Unit

RAIL & CLIP GUIDE

STD = 1-1/2" Tee Height, Tall = 1-11/16" Tee Height

CHECK RAIL & CLIP POSITIONS BEFORE INSTALLATION. ARROWS INDICATE SCREW POSITIONS.

TO CHANGE IN THE FIELD REMOVE AND REINSTALL ACCORDING TO DIAGRAMS BELOW.

G1: STD 15/16" Lay-In Tile

G2: STD 9/16" Lay-In Tile

G4: Tall 15/16" Lay-In Tile

G5: Tall 9/16" Lay-In Tile

G3: 9/16” Slot-Tee Tegular Tile

T1: STD 15/16” Tegular Tile

T2: STD 9/16” Tegular Tile

T4: Tall 15/16” Tegular Tile

T5: Tall 9/16” Tegular Tile

T6: 9/16” Node Tegular Tile

INDIVIDUAL INSALLATIONS FOLLOW STEPS 1, 2 & 6

1 2

SECURE TO

STRUCTURE ABOVE MAKE ELECTRICAL CONNECTIONS

2 3

CORNER UNIT MUST BE

JOINED TO ONE OF THE

LINEAR UNITS PRIOR

TO CEILING INSTALLATION

1REMOVE AND DISCARD JOINER

BRACKET FROM LINEAR UNIT WHEN

JOINING TO CORNER

CORNER ASSEMBLY

DRIVER SERVICE

2AVOID ALL CONTACT WITH

LED SURFACE, LEDs ARE

EASILY DAMAGED!

DO NOT

OVER-TIGHTEN

SECURE TO

STRUCTURE ABOVE

MAKE ELECTRICAL CONNECTIONS

Use a non-maring tool with

thin blade to safely remove louver

without causing damage

FULLY LOUVERED LOUVER AND LENS

LOUVER AND FACEPLATE

EM- MOUNTING HEIGHT

See Battery Manufacturer

Instructions

Emergency maximum mounting height:

External Switch: 26.4'

Internal Switch: 8.0'

Focal Point Seem 1 Louver Recessed FSM1C Installation guide

Focal Point Seem 1 Louver Recessed FSM1C Installation guide

Focal Point Seem 1 Louver Recessed FSM1C Installation guide

Related papers

Other documents