HK Instruments RHT Installation guide

  • Hello! I'm a chat assistant, and I've reviewed the installation instructions for the HK Instruments RHT Duct humidity transmitter. This document contains detailed information about the device's specifications, how to install it, its wiring, and configurable options, and its various measurement capabilities such as dew point, mixing ratio and others. I am ready to answer your questions about the RHT Duct device.
  • What are the measurement ranges for temperature and relative humidity?
    What is the accuracy of the temperature measurement?
    What is the accuracy of the relative humidity measurement?
    What is the power supply voltage for the device?
    What kind of output signals does it provide?
Copyright HK Instruments 2021 www.hkinstruments. Installaon version 8.0 2021
INSTALLATION
INSTRUCTIONS
HUMIDITY TRANSMITTERS
RHT Duct Series
READ THESE INSTRUCTIONS CAREFULLY BEFORE
ATTEMPTING TO INSTALL, OPERATE OR SERVICE THIS
DEVICE.
• Failuretoobservesafetyinformaonandcomplywith
instruconscanresultinPERSONALINJURY,DEATHAND/OR
PROPERTY DAMAGE.
• Toavoidelectricalshockordamagetoequipment,disconnect
powerbeforeinstallingorservicinganduseonlywiringwith
insulaonratedforfulldeviceoperangvoltage.
• Toavoidpotenalreand/orexplosiondonotuseinpotenally
ammableorexplosiveatmospheres.
• Retaintheseinstruconsforfuturereference.
• Thisproduct,wheninstalled,willbepartofanengineered
systemwhosespecicaonsandperformancecharacteriscs
arenotdesignedorcontrolledbyHKInstruments.Review
applicaonsandnaonalandlocalcodestoassurethatthe
installaonwillbefunconalandsafe.Useonlyexperiencedand
knowledgeabletechnicianstoinstallthisdevice.
ThankyouforchoosinganHKInstrumentsRHTDuctseriesrelave
humiditytransmier.TheRHTseriesisintendedforuseincommer-
cialenvironmentsinHVAC/Rapplicaons.
RHTDuctisarelavehumiditytransmierwithtemperatureoutput
installedinairvenlaonduct.Inaddiontothesemeasuredvalues,
RHTDuctcalculatesvariousparameterssuchasdewpoint,mixing
rao, enthalpy and absolute humidity. Illuminated display ensures
easyreadability alsofrom adistance.The RHT hasa screwless lid
andaneasilyadjustablemounngangethatmaketheinstallaon
ofthedeviceeasy.
RHTDuctseriesdevicesarecommonlyusedtomonitorandcontrol:
•Relavehumidityandtemperaturelevelsofincomingandreturnair
invenlaonsystem
SPECIFICATIONS
Performance
Measurement ranges:
Temperature:-30...80°C,sensor
Relavehumidity:0100%
Accuracy:
Temperature:<0.5ºC
Relavehumidity:±2...3%at0...50°Cand10–90%rH
Totalerrorbandincludesaccuracy,hysteresisand
temperatureeectover5...50°Cand10–90%rH.
Technical Specicaons
Media compability:
Dryairornon-aggressivegases
Measuring units:
°Cand%rH
Measuring element:
Temperature:NTC10k
Relavehumidity:Thermosetpolymercapacive
sensingelement
Environment:
Operangtemperature:0...50°C
Storagetemperature:-20...70°C
Humidity:0to95%rH,noncondensing
Physical
Dimensions:
Case:119x95.5x45mm
Probe:L=188mm,d=12mm
Mounng:
Withange,adjustable40...155mm
Weight:
150g
Materials:
Case:ABS
Cover:PC
Probe:ABS
Mounngange:LLPDP
Protecon standard:
IP54
Electrical connecons:
4springloadedterminals
(24V,GND,OUT1*,OUT2*)
0.2–1.5mm2(16–24AWG)
A-model:
2addionalspringloadedterminals
formA-output(OUT1*,OUT2*)
0.2-1.5mm2(16-24AWG)
*DefaultOUT1=rH,OUT2=TE
Outputsselectableonthedisplay:
temperature/dewpoint/mixingrao/
enthalpy/absolutehumidity/relavehumidity
Electrical
Supplyvoltage:24VACorVDC±10%
Currentconsumpon:max90mA(at24V)+10mAfor
eachvoltageoutput
Outputsignalsforeverymedia:
0/2...5/10VDC,LoadRminimum1kΩ
OnlyA-model:
4...20mA,LoadRmaximum500Ω,minimum20Ω
Outputcalibratedwithin±0.08mA
Conformance
Meetstherequirementsfor:
CE:  UKCA:
EMC:  2014/30/EU S.I.2016/1091
RoHS:  2011/65/EU S.I.2012/3032
WEEE:  2012/19/EU S.I.2013/3113
INTRODUCTION
APPLICATIONS
WARNING
RoHS
COMPLIANT
Copyright HK Instruments 2021 www.hkinstruments. Installaon version 8.0 2021
SCHEMATICS
DIMENSIONAL DRAWINGS
INSTALLATION
STEP 1: MOUNTING THE DEVICE
1)Mountthedeviceinthedesiredlocaon(seestep1).
2)Routethecablesandconnectthewires(seestep2).
3)Thedeviceisnowreadyforconguraon.
WARNING!Applypoweronlyaerthedeviceisproperlywired.
1)Selectthemounnglocaon(onaduct).
2)Usethemounngangeofthedeviceasatemplateandmarkthe
screwholes.
3)Mounttheangeontheductwithscrews(notincluded).(Figure
1a)
4)Adjusttheprobetothedesireddepth.Ensurethattheendofthe
probereachesthemiddleoftheduct.(Figure1b)
5)Tightenthescrewontheangetoholdtheprobeinposion.
Figure 1a - Mounng a ange
Figure 1b - Mounng the probe in a ange
Air flow direcon Air flow direcon
Air flow direcon Air flow direcon Air flow direcon
Strain relief facing down
Figure 1c - Mounng orientaon
Display connecon
OUT 2
24 V
GND
Joysck 1
Joysck 2
Joysck 3
Select
Up
Down
Menu buons OUT 1
mA Out (oponal)
OUT 1
OUT 2
119.0
95.5
119.0
45.0
88.5
188.0
Tighten the
screw
Copyright HK Instruments 2021 www.hkinstruments. Installaon version 8.0 2021
STEP 3: CONFIGURATION
CONFIGURATION CONTINUED
ConguraonoftheRHTDuctseriesdeviceconsistsof:
Conguraonmenuopons.(Displayversionsonly.)
Presstheselectbuontoacceptchanges.Movetothenextset-
ngbypressingthedownbuon.Selecttheexitmenutosavethe
sengs.Ifthebuonsareunusedfor3minutes,thebasicviewwill
reappearautomacallyandthechangedsengsarenotsaved.
1)AcvatethedeviceMenubypushingtheselectbuonfor2
seconds.
ForCEcomplianceaproperlygroundedshieldingcableis
required.
1)Unscrewthestrainreliefandroutethecable(s).
2)Connectthewiresasshowningure2.
3)Tightenthestrainrelief.
OUT 1
OUT 2
24 V
GND
+Power Supply
24VDC / 24VAC
Output 0/2...5/10 V
Output 0/2...5/10 V
OUT 1
OUT 2
Output 4...20 mA
Output 4...20 mA Oponal mA output
OUTPUT 1
RH
SELECT
UP
DOWN
5)Selecttheoutput2value.
 (temperature/dewpoint/mixingrao/enthalpy/
absolutehumidity/relavehumidity)
SELECT
UP
DOWN
OUTPUT 2
TEMPERATURE
7)Selecttheoutputrange(0...10V,2...10Vor0...5V)
OUT VOLTAGE
0- 10 V
SELECT
UP
DOWN
10)Pushtheselectbuontoexitmenu.
SELECT
EXIT MENU SELECT
STEP 2: WIRING DIAGRAMS
Figure 2 - Wiring diagram
8)Selecthumidityoset:±10%rH,Osetfeatureenables
eldcalibraon.Thisisnecessaryindemandingapplicaons
requiringannualcalibraon.
9)Selecttemperatureoset:±5°C.
RH OFFSET
0.0 %RH
SELECT
UP
DOWN
TE OFFSET
0.0 °C
SELECT
UP
DOWN
4)Selecttheoutput1value.
 (temperature/dewpoint/mixingrao/enthalpy/
absolutehumidity/relavehumidity)
6.1)Setthelowlimitfortheoutput1(selectedinstep4).
RH OUT MIN
0.0 %RH
SELECT
UP
DOWN
6.2)Setthehighlimitfortheoutput1(selectedinstep4).
SELECT
UP
DOWN
RH OUT MAX
100.0 %RH
2)Selectthevalueshownonthedisplayrow1.
 (temperature/dewpoint/mixingrao/enthalpy/
absolutehumidity/relavehumidity)
DISPLAY ROW1
DEW POINT
SELECT
UP
DOWN
SELECT
UP
DOWN
DISPLAY ROW2
ENTHALPY
3)Selectthevalueshownonthedisplayrow2.
 (temperature/dewpoint/mixingrao/enthalpy/
absolutehumidity/relavehumidity)
6)Setthelimitsfortheoutputs.
 NOTE!Onlyselectedoutputsareshown.
Measurement Default range
Adjustable
low limit
Adjustable
high limit
Smallest range
available
Relavehumidity(RH) 0...100%rH 0...90%rH 10...100%rH 10%rH
Temperature(TE) 0...50°C -30...45°C 5...80°C 5°C
Dewpoint(DP)* -20...80°C -30...70°C -20...80°C 10°C
Mixingrao(MR)* 0...80g/kg -30...70g/kg 20...80g/kg 10g/kg
Enthalpy(ENT)* 0...85kJ/kg 0...85kJ/kg 5...90kJ/kg 5kJ/kg
Absolutehumidity(AH)* 0...80g/m³0...70g/m³10...80g/m³10g/m³
*)calculaonisbasedontemperatureandhumiditymeasurementsandconstant
pressurep=1013mBar
*)totalaccuracyisbasedontheaccuraciesofthemeasuredvalues(TandrH)andthedeviaon
fromtheassumedpressurep=1013mBar
High
limit
Low
limit
5/10 V
20 mA
0/2 V
4 mA
6.3)Setthelowlimitfortheoutput2(selectedinstep5).
TE OUT MIN
0.0 °C
SELECT
UP
DOWN
6.4)Setthehighlimitfortheoutput2(selectedinstep5).
SELECT
UP
DOWN
TE OUT MAX
50.0 °C
Copyright HK Instruments 2021 www.hkinstruments. Installaon version 8.0 2021
WARRANTY POLICY
Thesellerisobligatedtoprovideawarrantyofveyearsforthedeliv-
eredgoodsregardingmaterialandmanufacturing.Thewarrantyperiod
isconsidered tostartonthe deliverydate oftheproduct.Ifa defect
in raw materialsora producon aw isfound, theseller isobligated,
whentheproductissenttothesellerwithoutdelayorbeforeexpira-
onofthewarranty,toamendthemistakeathis/herdiscreoneither
by repairing the defecve product or by delivering free of charge to
thebuyeranewawlessproductandsendingittothebuyer.Delivery
costsfor therepairunderwarranty willbepaidbythebuyerandthe
return costs by the seller. The warranty does not comprise damages
causedbyaccident,lightning,oodorothernaturalphenomenon,nor-
malwearandtear,improperorcarelesshandling,abnormaluse,over-
loading,improperstorage,incorrectcareorreconstrucon,orchanges
andinstallaonworknotdonebytheseller.Theseleconofmaterials
fordevicespronetocorrosionisthebuyer’sresponsibility,unlessother-
wiseislegallyagreedupon.Shouldthemanufactureralterthestructure
ofthedevice, thesellerisnotobligatedtomakecomparablechanges
todevicesalreadypurchased.Appealingforwarrantyrequiresthatthe
buyerhascorrectlyfullledhis/herduesarisenfromthedeliveryand
stated in the contract. The seller will give a new warranty for goods
thathavebeenreplacedorrepairedwithinthewarranty,howeveronly
totheexpiraonoftheoriginalproduct’swarrantyme.Thewarranty
includestherepairofadefecvepartordevice,orifneeded,anewpart
ordevice,butnotinstallaonorexchangecosts.Undernocircumstance
isthesellerliablefordamagescompensaonforindirectdamage.
RECYCLING/DISPOSAL
The parts le over from installaon should be
recycled according to your local instrucons.
Decommissioned devices should be taken to a
recyclingsitethatspecializesinelectronicwaste.
/