Workrite Ergonomics Swivel, Swing Keyboard Platform Installation guide

Brand
Workrite Ergonomics
Model
Swivel, Swing Keyboard Platform
Type
Installation guide
1 of 2 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com
A Keyboard Platform
Qty: 1
Assembly & Installation Instructions:
Keyboard Platforms:
1 Mount Keyboard Platform to Arm
1.1 Place the Keyboard Platform (A) on the keyboard
arm and align the four holes on the platform with
the four holes in the Arm.
1.2 Insert the #10-32 × ½" Flat Head Screws (B)
through holes on platform, through the holes in
the arm and fasten using four ⅜" #10-32 Keps
Nuts(C). Tighten securely using Phillips head
screwdriver.
Note: Mount your Leader Arm with Track to your worksurface using the instructions that came with your Leader
Arm.
Tools RequiredRequired
Wrench with ⅜" socket
#2 Phillips screwdriver or drill/driver
5 mm & " Allen Wrenches to convert to le handed
Leader Standard or Sit-Stand Keyboard Arm with Track
C ⅜" #10-32 Keps Nuts
Qty: 4
D Cable Clips
Qty: 4 E Friction Pads
Qty: 2
B #10-32 × ½" Flat
Head Screw
Qty: 4
Hardware Kit: #4200094
Parts Included
2 Attach Cable Clips and Route Keyboard and Mouse Cords
Note: Make sure your keyboard arm is fully
extended before routing your cables.
2.1 Place one Cable Clip (D) on the side of the arm
mechanism. Place the other Cable Clip on the
rear of the track. Do the opposite side in the
same fashion if cords run down the le side.
2.2 Route the Keyboard and mouse cords through
Cable Clips and be sure to leave enough slack
in cord to allow for unrestricted movement of
the mouse.
Caution: Adhesion is designed to bond
immediately. You will not be able to
reposition the clip once it's in place.
or
A
C
1.2
1.1
Keyboard Arm
Worksurface
Swivel Platform shown
2.1
2.1
2.2
D
D
Under Worksurface
Arm fully extended
Cables will be out of the way
when platform is in use
B
Swivel PlatformSwing Platform
2 of 2 Workrite Ergonomics | (800) 959–9675 www.workriteergo.com
1500367 Rev A
3 Apply Friction Pads or Hook & Loop Squares
Place Friction Pads (E) on the bottom surface of your keyboard
to keep it in place, if necessary. The Friction Pads will keep your
keyboard from sliding when the platform is angled.
4 Configuring Swivel Models for Le Handed Use
Swivel Platforms are pre-configured for right handed use but can be
converted to le handed use.
4.1 Remove the Wrist Rest by removing the three screws from under the
Keyboard Platform.
4.2 Remove the Mouse Platform using both a 5 mm and a " Allen Wrench.
Set all subcomponents aside noting the placement. See
4.4
below.
4.3 Remove the Wire Mouse Trap from the
Mouse Platform and flip the Mouse Pad
over.
4.4 Reattach the Mouse Platform on opposite
sides for le handed use then replace the
Wire Mouse Trap and Wrist Rest.
4.5 Remove Mouse Surface from bottom of
Mouse Pad and replace on top side.
Go to www.workriteergo.com/
instructions to find the Leader Arm User
Guide for instructions on how to set up
this product for ideal ergonomic benefit.
Machine Screw
Keyboard Platform
Spacer
Mouse Platform
Flat Washer
Joint Connector Nut
4.1
4.3
4.2
E
E
Disassemble
Flip
Reassemble
4.4
4.5
  • Page 1 1
  • Page 2 2

Workrite Ergonomics Swivel, Swing Keyboard Platform Installation guide

Brand
Workrite Ergonomics
Model
Swivel, Swing Keyboard Platform
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents