Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Integra™ Operatory Cabinetry - Side Cabinetry

Brand: Midmark

Model: Integra™ Operatory Cabinetry - Side Cabinetry

Type: Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions to optimize your dental operatory space. Designed for easy positioning and leveling, it features adjustable leveling screws and can be connected to additional units for expanded storage. The cabinet comes with various drawer options, including 2” metal frame, writing surface assembly, and molded drawers, providing ample storage for dental supplies and equipment. It also allows for countertop installation, extending 3/8” to 1/2” over each end of the cabinet for a seamless look.

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions to optimize your dental operatory space. Designed for easy positioning and leveling, it features adjustable leveling screws and can be connected to additional units for expanded storage. The cabinet comes with various drawer options, including 2” metal frame, writing surface assembly, and molded drawers, providing ample storage for dental supplies and equipment. It also allows for countertop installation, extending 3/8” to 1/2” over each end of the cabinet for a seamless look.

1

DA2163i

003-1920-00 Rev.A

12”, 15”, 18”, 24”, Side Storage Unit Installation

Applies to Models:

OSC012, 015, 018, 024

Special Tools:

Level

1/4” deep well socket

OSC012 (12” Side Storage Unit)

OSC015 (15” Side Storage Unit)

OSC018 (18” Side Storage Unit)

OSC024 (24” Side Storage Unit)

OSC024 (Shown)

DA2162i

Step 1: Lift or push down release

levers (one per side) and

slide out drawer assembly.

Step 1: Pull drawer outward

until it hits stop.

Step 2: Pull sides of drawer outward

while lifting to free back of

drawer from hooks and remove.

2” Metal Frame Drawers

or

Writing Surface Assembly

All Molded Drawers

DRAWER REMOVAL

(If Required for Access)

NextNext

2

DA2164i

WALL

DESIRED POSITION OF EDGE OF UNIT

Storage

RAISE

CABINET

LOWER

CABINET

1 1/2" (max.)

(3.8 cm)

POSITIONING & LEVELING

Step 1: Remove bottom drawer or

bottom panel from cabinet.

Step 2: Adjust leveling screws

to fully lowered position

and move cabinet to

desired position.

Step 3: Level cabinet with

leveling screws.

Equipment Alert

Do not adjust leveling screws more then

1 1/2” (3.8 cm) to prevent lose of stability.

NextNext

BackBack

3

DA2165i

Step 2: Position counter top so it

extends 3/8” (0.95 cm) to

1/2” (1.3 cm) over each

end of cabinet(s) and secure

with provided screws.

Step 1: If necessary, level and

connect any additional

storage units.

Note

If necessary, sand

counter top to form

to wall.

Special hex bolts

(#10-24 x 3/4”)

CONNECTING ADDITIONAL UNITS

& COUNTER TOP INSTALLATION

NextNext

BackBack

4

DA2178i

1/8"

Vertical Adjustment

A) Loosen both screws.

B) Move up or down.

C) Retighten screws.

Horizontal Adjustment

A) Turn cam screw to move

panel side to side.

Depth Adjustment

A) Turn cam screw to move

panel front to back.

Note

Door should be adjusted for the

gap specified on the illustration.

DOOR ADJUSTMENT

NextNext

BackBack

5

BackBack

Midmark Corporation

For contact information, go to:

www.midmark.com

1
2
3
4
5

Midmark Integra™ Operatory Cabinetry - Side Cabinetry Installation guide

Integra™ Operatory Cabinetry - Side Cabinetry

Brand: Midmark

Model: Integra™ Operatory Cabinetry - Side Cabinetry

Type: Installation guide

Midmark Integra™ Operatory Cabinetry - Side Cabinetry offers versatile storage solutions to optimize your dental operatory space. Designed for easy positioning and leveling, it features adjustable leveling screws and can be connected to additional units for expanded storage. The cabinet comes with various drawer options, including 2” metal frame, writing surface assembly, and molded drawers, providing ample storage for dental supplies and equipment. It also allows for countertop installation, extending 3/8” to 1/2” over each end of the cabinet for a seamless look.

Related papers

Other documents