XW/R/IQ Wireless Sensor Receiver Installation Instructions TG200783 Issue 3, 06-Mar-2013 1
Installation Instructions
XW/R/IQ
Wireless Sensor Receiver
Important: Retain these instructions
1
Dimensions
2
Requirements
UNPACKING
INSTALLATION
XW/R/IQ Installation
Instructions TG200783
a
mounting slot
R J11
plug
b
HO
2
-35 °C
+70 °C
0 %RH
100 %RH
c
d
Protection IP68+
• Avoid using many other devices on
frequency range 433.05 to 434.79 MHz
• Keep away from sources of interference
(e.g. computer >1 m, 1 yd, microwave
ovens, switch mode power supplies).
• Mount above partition height if possible.
XW/R/IQ
75 m, 80 yds
(maximum)
Note that range may be affected
by environmental characteristics,
e.g. partitions, walls, building
structure etc.
37 mm
(1.46”)
40 mm
(1.57”)
174 mm (6.85”)
4 m
(4 yds 1’)
Ø 20 mm
(0.78”)
45 mm (1.77”)
(-31 °F) (+158°F)
2 XW/R/IQ Wireless Sensor Receiver Installation Instructions TG200783 Issue 3, 06-Mar-2013
XW/R/IQ Installation Instructions
3
Requirements
5
Congure Reciever
4
Install sensors
INSTALLATION (continued)
(1) Using plastic bracket supplied
TW/S Installation Instructions TG200781
TW/P Installation Instructions TG200782
(a) x bracket (b) (c)
(2) Using cable tie to pipe
(2) Using stainless steel bracket accessory ACCW/FK/SS
(a) (b)
(c)
use screws
and rawl plugs
use screws and rawl plugs
(a) Connect to PC and 24 Vac
(b) Check the following settings in XW/R/IQ Conguration Tool:
b1: Port is set to appropriate port number
b2: Protocol is set to Trend Protocol
b3: Read Channels 1-16 (if some channels already set up)
100-240 V
OK RX
24 Vdc Aux supply out
RJ11 socket RJ11 plug
2 screw terminal
9 way D type female
conguration cable EJ105784
(part of ACCW/CONFIGKIT)
RS232 port
XW/R/IQ Conguration
Tool CD (part of ACCW/
CONFIGKIT)
ensure correct
polarity
(+24 V) Red Black (0 V)
XW/R/IQ
<=50 mA
(3 m long)
(1.5 m long)
XW/R/IQ Wireless Sensor Receiver Installation Instructions TG200783 Issue 3, 06-Mar-2013 3
Installation Instructions XW/R/IQ
5
Congure Reciever (continued)
INSTALLATION (continued)
(d) Congure Table and PIN (if required) (repeat steps c2, c3 for all sensors)
Notes:
1 If the values from the XW are to be sent to more than one controller, check if passwords
(PINs) set up in any of them. One PIN must be the same in all controllers and of priority
level >=95.
2 If sensor value is to be sent to another controller (other than the local controller) the local
supervisor port address must be greater than zero.
(e) Congure Table into XW
e1 Change Conguration/Output Mode to ‘5 Programmed Transmitter Trend Protocol
(ASCII)’
e2 Select Conguration/Programme Channels 1-16
e3 Select Conguration (Read Channels 1-16) and check table is correct
Note that to program channels 17-32 select:
Read Channels 17-32 step b3
Program Channels 17/32 step e2
Read Channels 17-32 step e3
sensor’s identication number
(f) Unplug XW/R/IQ receiver from adaptor cable
CAUTION
Ensure that the menu item Conguration/Output Mode is set back to ‘5 - Programmed
Transmitters Trend Protocol (ASCII)’ or the receiver will not operate.
!
(c) c1: Select Conguration/Output Mode 0 - All transmitters [Binary]
(conguration software communications window will show communications from sensors)
c2: Select appropriate sensor identication no. from window
e.g. Thermistor Temperature TX.: 16946 Temperature: 26.8
ADC: 367 f/w V4 $---- etc.
communications window
sensor table
PIN
conguration software
sensor’s identication number
c3: Type sensor ident ication number into Transmitter
Address slot, and type its Analogue Node Number, and
O/S (outstation) Address into adjacent slots in table
TW/.., XW/R/IQ data sheet
TA200780
XW/R/IQ Conguration
Tool Manual TE200793
metItluafeDfiegnahCotegnahCetoN
rebmunNIP4321
evah)s(rellortnoC
putes)s(sdrowssap
'4321'ottnereffid
)s(rellortnocnidesuNIP
59=>levelytiroirpfo
1
rettimsnarT
woRrettimsnarT
sserddA
0rettimsnartwenputesot
noitacifitnedirosneS
rosnesmorfrebmun
8(lebalnoitacifitnedi
)stigid
eugolanA
.oNedoN
000rettimsnartwenputesot
nirebmunedoneugolanA
rosneserotsotrellortnoc
eulav
S/O
sserddA
0rettimsnartwenputesot
nosserddarellortnoC
ebnac(krowtenlac
ol
rehtonarorellortnoclacol
)krowtennorellortnoc
1
2
Note: if no reception from sensor, see step 6 below.
4 XW/R/IQ Wireless Sensor Receiver Installation Instructions TG200783 Issue 3, 06-Mar-2013
XW/R/IQ Installation Instructions
Please send any comments about this or any other Trend technical publication to [email protected]
© 2013 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division
of Honeywell Technologies Sàrl, Ecublens, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited
.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation
to notify any person of such revisions or changes.
Trend Control Systems Limited
Albery House, Springeld Road, Horsham, West Sussex, RH12 2PQ, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trendcontrols.com
Trend Control System USA
6670 185
th
Avenue NE, Redmond, Washington 98052, USA. Tel:(425) 869-3900 Fax:(425) 869-8445 www.trend-americas.com
6
If there is reception failure of sensor
7
Congure IQ controller strategy
8
Connect receiver to controller
9
Test System
5 DISPOSAL
WEEE Directive :
At the end of their useful life the
packaging and product should be
disposed of by a suitable recycling
centre.
Do not dispose of with normal household
waste.Do not burn.
either for IQ3 or current IQ2xx (excluding IQ251)
IQ
∆ T
e.g. TB/TI/..
XW/R/IQ
or IQ251 and older IQ2xx’s without 24 V on
local supervisor port
or IQ4 must use an external 24 Vdc supply
100-240 V
OK RX
local supervisor port
RJ11
local supervisor port
RJ11 local
supervisor port
RJ11
24 Vdc
Aux
24 Vdc
Supply
Note XW/R/IQ current consumption <= 50 mA
1 Check compliance with step 2 sections C & D
2 Move sensor or receiver slightly in case of a standing wave null position
IQ3 or current IQ2xx (not
IQ251)
IQ251
or older
IQ2xx’s
IQ4
For IQ3 or IQ4 the sensor’s target analogue node
must be created using SET. An example strategy
including decoding of alarm bits is given in the
TW/.., XW/R/IQ data sheet
TW/.., XW/R/
IQ Data Sheet
TA200780
RD/SDU-ADAPTOR IQ2xx
RD/SDU-ADAPTOR IQ2xx
INSTALLATION (continued)
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Trend TW/P Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
Johnson Controls IQ Panel 4-IQ4 Hub User guide
-
Rain Bird IQ4 User guide
-
Johnson Controls iQ User guide
-
Racepak 250-DS-IQ3S Owner's manual
-
Foxtel iQ3 Domestic Installation Manual
-
Intellihot iQ251 Series User manual
-
-
-
Wifx Lorix One Quick start guide
-
Enersys Truck iQ User manual
