TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 2, 08/03/2011 1
Installation Instructions
TB/TS
Thermistor Room Temperature Sensors
Important: Retain these instructions
Dimensions
INSTALLATION
1
Requirements
2
b
a
UNPACKING
85 mm (3.35”)
26 mm (1.02”)
85 mm (3.35”)
c
> 50 cm (20”)
e
d
f
g
1.5 m
(5 ft)
TB/TS Installation
Instructions TG200604
2 TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 2, 08/03/2011
TB/TS Installation Instructions
INSTALLATION
(continued)
Requirements (continued)
2
4
Remove cutout(s)
5
Route cables
6
i
j
l
-10 °C
(14 °F)
+50 °C
(122 °F)
0 %RH
90 %RH
OR wall
EITHER mount to BESA box
35 mm (1.38”)
OR wall box
h
as required
Remove backplate
3
a
b
0 °C
(32 °F)
+40 °C measurement
60 mm (2.36”)
35 mm (1.38”)
35 mm (1.38”)
35 mm (1.38”)
(104 °F)
FR
ABS
k
Mount backplate
TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 2, 08/03/2011 3
Installation Instructions TB/TS
INSTALLATION (continued)
Wire to controller
7
if IQ
Assemble unit
8
‘click’
0 V
Temperature
IN
SENSOR
IQ
TB/TS
linked for thermistor (T)
analogue input
COM (0V)
if IQL
TB/TS
9
10
1
11
12
13
3
COM
C
2
IQL11+/24VAC
TB/TS
COM
15 16 17 18 19
1
23
C
IQL11+/230
TB/TS
COM
21 22 23 24 25 26 27 28
COM
1
234
5
C
IQL13+, 15+, 16
Note that screened cable is not required for
sensor wiring to IQLs. If screened cable is used,
the screen must be terminated at the controller
to its supply cable earth.
polarity independent
IQL OPTIONS
IQL11+, 13+, 15+, 16, 17 TB/TS
Terminal size 0.5 to 2.5 mm
2
(14 to 20 AWG)
TB/TS
COM
21 22 23 24 25 26 27 28
1
234
5
C
0V
AI
10V
IQL17
0 V
Temperature
N (in)
SENSOR
IQ3
TB/TS
+ (+24V)
0 (0V)
N
analogue input linked
for thermistor (T)
4 TB/TS Thermistor Room Temperature Sensors Installation Instructions TG200604 Issue 2, 08/03/2011
TB/TS Installation Instructions
Please send any comments about this or any other Trend technical publication to [email protected]
© 2011 Honeywell Technologies Sàrl, ECC Division. All rights reserved. Manufactured for and on behalf of the Environmental and Combustion Controls Division
of Honeywell Technologies Sàrl, Ecublens, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited
.
Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation
to notify any person of such revisions or changes.
Trend Control Systems Limited
Albery House, Springeld Road, Horsham, West Sussex, RH12 2PQ, UK. Tel:+44 (0)1403 211888 Fax:+44 (0)1403 241608 www.trendcontrols.com
Trend Control System USA
6670 185
th
Avenue NE, Redmond, Washington 98052, USA. Tel:(425) 869-3900 Fax:(425) 869-8445 www.trendcontrols.com
∆ T
WEEE Directive :
At the end of their useful life the
packaging and product should be
disposed of by a suitable recycling
centre.
Do not dispose of with normal household waste.
Do not burn.
Test system
INSTALLATION (continued)
Set up IQ Sensor types
9
If IQL
10
If IQ
IQL Strategy Installation
Instructions
It is recommended to use SET (software tool) for the setting of sensor type modules. For all
IQ2 series controllers with rmware version 2.1 or greater, or IQ3 series controllers, select the
appropriate SET Unique Sensor Reference from the following:
Thermistor: Thermistor TBTS (°C)
Thermistor TBTS F (°F)
Alternatively, set scaling mode to 5 (characters) and enter scaling manually, as dened in the
table below.
Note that for IQ3 the scaling mode and exponent (E) do not need to be set up.
For all other IQ controllers see Sensor Scaling Reference Card TB100521A
DISPOSAL
Units °C °F
Y Input type
1 (thermistor volts)
E Exponent
3
U Upper
50 122
L Lower -5
23
P Points
6
x Ix Ox (°C) Ox (°F)
1
2.641 50 122
2
3.47 40 104
3
4.46 30 86
4
6.663 10 50
5
7.668 0 32
6
8.102
-5
23
/
