Trend IQ4NC/12 Installation Instructions Manual

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018 1

InstallationInstructions-Conguring

IQ422, IQ4NC/00, IQ4NC/12

Controllers

Important: Retain these instructions

These instructions shall be used by trained service

personnel only.

If the equipment is used in a manner not

speciedbytheseinstructions,theprotectionprovidedbythe

equipmentmaybeimpaired.

https://partners.trendcontrols.com

Isolate All Power (includinganyI/Osupplies)

1 BEFORE STARTING CONFIGURATION

CONTENTS

1 BeforeStartingConguration.......................................1

2 Conguration.................................................................1

3 Connect to IQ4xx........................................................10

4 Reset to Defaults.........................................................12

2 CONFIGURATION

Read&AgreetoEndUserLicenceAgreement

Additional Documentation Required

▪ SETManual(TE200147)

▪ IPToolManual(TE200638)

▪ IQToolMonitorAppletManual(TE201298)

▪ IQToolAddresserAppletManual(TE201299)

▪ IQ4CongurationManual(TE201263)

Note: PDF copies are included with SET installation in the

following folder: C:\...\Trend Control Systems\Documentation

IQ422, IQ4NC/00, IQ4NC/12 Installation

Instructions-Mounting(TG201264)

SETManual(TE200147)

Prepare Ethernet Network (ifusingEthernet)

Install DHCP Server

IftheIPaddresssettings(IPaddress,subnetmask,default

router,WINSandDNSservers’addresses)aretobesupplied

by a DHCP server, ensure one is installed onthe Ethernet

segment to which the IQ422, IQ4NC/00, IQ4NC/12 is

connected.

Install WINS Server

If host names are being used for IP addressing across a

router,aWINSservermustbeinstalled.

Install DNS Server

Ifemailalarmsarebeingsent,andtheemailserveraddress

isidentiedbyinternetdomainname,aDNSservermustbe

installed.

IQ422, IQ4NC/00, IQ4NC/12 Installation

Instructions-Mounting(TG201264)

PSU

Install the IQ422, IQ4NC/00, IQ4NC/12 InstallSETonPC/Laptop

WARNING Connecting leads may be connected

topowersupplies.Isolatebeforetouching.

2 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

Select Terminator Switch Position (IQ4NCusingMS/TPnetworkonly)

PeelOﬀTopSerialLabel&Retain

Disconnect All I/O

OpenRotatingCovers

Open Panel / Enclosure

2 CONFIGURATION (continued)

Serial

Number

nq4eyecp412345

Q422B_V53440388

O/S

Q422B_V53440388

nq4eyecp412345

00:10:70:0D:1E:92

MAC Addr

IQ411-1010U5000

Part No:

LAN

422

MAC

Addr

LAN

Location

S/No:

MAC Addr

00.10.70.00.UD.BB

S/No:

Q3B____X73010003

IP Addr

Location

TerminatoroutofcircuitTerminatorincircuit

IQ422, IQ4NC/00, IQ4NC/12 Installation

Instructions - Mounting (TG201264) for

detailsofterminatoruse.

Leave Power, Ethernet, Current loop LAN, USB, RS232,

andMS/TPconnected(whereappropriate).

WARNING Opening the panel may expose

dangerousvoltages.

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018 3

InstallationInstructions-Conguring IQ422, IQ4NC/00, IQ4NC/12

CloseRotatingCovers

CheckPower&WatchdogIndicators

Switch On Power to IQ4xx

ConnectPC/Laptop

Check Ethernet Indicators (ifEthernetisconnected)

2 CONFIGURATION (continued)

Either:viaEthernetHub/Switch Or:usingdirectconnection

Note: To connect with SET a vCNC is required (see step 14).

SETcanconnectwhenonadiﬀerentsubnet.

Note:Othermethodsofconnectionareavailablesee‘Connect

to IQ4xx’ on page 10.

Normal operation indication

Power

Watchdog

Fault indications

Power

Checkinputpowersupply

Watchdog

Devicefault.TryresettingtheIQ4xx

todefaultsettings(seepage12).

10s

Normal operation indication

Fault indications

CheckEthernet

RJ45

StandardEthernetcable

(Cat5etwistedpair)

max100m(109yds)

StandardEthernetcable

(Cat5etwistedpair)

max100m(109yds)

RJ45

Hub/Switch

Router

Note: All LEDs illuminate for several seconds after switch on.

Watchdog

(red)

Power

(green)

(yellow)

4 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

Connect to the IQ4xx

SetupIPAddressingDetails(ifusingEthernet)

2 CONFIGURATION (continued)

nq4eyecp412345

Q422B_V53440388

O/S

00:10:70:0D:1E:92

MAC Addr

IQ422-1010U5000

Part No:

LAN

Addr

422

Then nd the IQ4NC, IQ422by its MAC

addressasshownonseriallabel

SETManual(TE200147)

IPToolManual(TE200638)

UseIPTool–seestep12–tochooseeitherstatic(xed)or

dynamic(DHCP)addressing:

Dynamic(DHCP)Addressing(default)

Parameter Value

DeviceMode

Static(Fixed)Addressing

Parameter Value

DeviceMode

IPAddress

Enterrequiredvalueinformat:

xxx.xxx.xxx.xxx

SubnetMask

Default Router

WINSServer

Whensettodynamic(DHCP)addressingtheunitautomatical

obtains its IP addressing details (IP address, subnet mask,

default router, WINS server and DNS server) from the

network’s DHCP (Dynamic Host Conguration Protocol)

server. If no DHCPserver isfound, theunitdefaults to link/

localmodewhereitautonegotiatesitsIPaddresswithother

devicesonitsEthernetsegment,

Note: It is recommended that link/local only be used on a

single segment system.

When set to static (xed) addresssing the IP addressing

detailsmustbeconguredmanually.

Note: If email alarms are being sent, and the email server

address is identied by internet domain name, then a DNS

servermustalsobespeciedusingTextComms.

IPToolManual(TE200638)

UsingthePC/laptop(seestep7)runSET/IPTool

Set up Virtual CNCs (ifrequired)

Bydefault,IQ4NCshave4enabledvCNCs(4,5,6,and7)and

IQ422s have 3 disabled vCNCs. A vCNC must be enabled

if connection to a supervisor, tool or display is required. If

necessarydisable/congurethemtoavoidaddressconicts.

Use IP Tool – seestep12– to set up theaddressandport

numberofeachvCNC.

Parameter Range

Address

0(disabled),1,4to9,11to119

PortNumber

1to32767

Default = 10000 plus the address

(e.g.address23setsportto10023)

OncethevCNCsetupinIPTooliscomplete,useIQSETto

congurethevCNCs.

▪ UsingIQSETconnecttooneofthecontroller’svCNCs.

▪ Youwillbe promptedtopresstheservicebutton on the

controller.OncepressedtheSecureSiteConguration

dialogueboxisdisplayed.

▪ Congure the vCNCs as required, and enter the

credentialsfortheCNCUsermodule.

Note: conguring the vCNCs require physical access to

the controller ensure this is done before leaving site.

SETManual(TE200147)

IPToolManual(TE200638)

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-20185

InstallationInstructions-Conguring IQ422, IQ4NC/00, IQ4NC/12

Set up IQ4NC Communication Mode (ifusingIQ4NC)

CheckTrendCurrentLoopNetworkIndicators(ifcurrentloopnetworkbeingused)

Check MS/TP Network Indicators (IfIQ4NCusingMS/TPnetwork)

▪ ConnectaPCdirectlytotheIQ4usinganEthernetcable,

see‘ConnecttoIQ4’onpage10.

▪ Usinga web browser, e.g. Internet Explorer, access the

controller’swebpagesandselectModules>Networks to

displaytheNCCongurationWizard.

▪ Click required mode, and if necessary specify any

parameterse.g.LANnumber.

▪ Click

;thecontrollerwillrestart.

EthernetInternetworktotoMS/TPLAN(default)

Parameter Notes

LANnumber

1,4to9,11to119

BACnetIP

Canbedisabled

CurrentLoopInternetworktoMS/TPLAN

Parameter Notes

LANnumber

1,4to9,11to119

BACnetIP

Canbedisabled

EthernetInternetworktoCurrentLoopLAN

Parameter Notes

LANnumber

1,4to9,11to119

BACnetIP

Canbedisabled

BACnet

MSTP

Can be enabled e.g. for

connectionofPEHAdevices

Ethernet Internetwork to Current loop

Internetwork

Note:Addressnolongerneedstobe>100.

Parameter Notes

LANnumber

1,4to9,11to119

BACnetIP

Canbedisabled

BACnet

MSTP

Can be enabled e.g. for

connectionofPEHAdevices.

Manualconguration

E.g. Ethernet Internetwork to Current loop

InternetworkplusMS/TPLan

2 CONFIGURATION (continued)

IQ4WebUserGuide(TC201256).

Note: The IQ4NC always has a LAN to connect to the

internetwork so cannot join another LAN on the internetwork.

Normal operation indication

Fault indications

Checkconnectiontodownstreamdevice

Checkconnectiontoupstreamdevice

Normal operation indication

Fault indications

Signal not reaching RX on downstream

deviceonnetwork–checkdevice/wiring

No TX signal from upstream device on

network–checkdevice/wiring

(yellow)

6 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

SetupTrendAddressing

Set up Ethernet Access Across Routers (ifrequired)

WriteAddressDetailsonLabel

2 CONFIGURATION (continued)

IftheLANistobebuiltacrossarouter(s)detailsofdevices

(on each subnet) must be specied to enable cross-router

communications.

UseIPTool–seestep12–tospecifyIPsettingsforupto20

devicesintheRemoteTrendDeviceslist:

Parameter

Value

IPAddress

If using dynamic (DHCP) addressing:

Enterthehostnameoftheremotedevice.

Ifusingstatic(xed)addressing:

EntertheIPAddressoftheremotedevice,

intheformat:xxx.xxx.xxx.xxx

SubnetMask

Thesubnetmaskfortheremotedevice,in

theformat:xxx.xxx.xxx.xxx

IPToolManual(TE200638)

It is recommended that atleasttwodevicesfromeachsubnet

are specied. For increased reliability details of additional

devicesshouldbespecied.

IfstaticIPaddressingisbeingusedthelistshouldcontainthe

deviceswiththelowestIPaddresses.

ThesamelistmustbecopiedtootherEINCtypedeviceson

thenetwork.

Hint:TickingthecheckboxnexttotheRemoteTrendDevices

listretainsthelistinIPTool,allowingittobeeasilycopiedto

other devices:

nq4eyecp412345

Q422B_V53440388

O/S

00:10:70:0D:1E:92

MAC Addr

IQ422-1010U5000

Part No:

LAN

Addr

422

IPToolManual(TE200638)

IQTool Addresser Applet Manual

(TE201299)

IfconnectingtoaLANonEthernet(orstandalonemode):

▪ UseIPTool–seestep12–tosetthedeviceaddressand

LANnumber.

IQ4xx controllers are given a default device address and

LANnumberinthefactory.Thedeviceaddressissetinthe

range11to119onarollingbasiswiththeLANnumbersetto

20. Therefore it may be necessary to set the address/LAN

numberasrequired.

Parameter Value

LocalAddress

1,4to9,11to119

(mustbeuniqueonLAN)

LocalLAN

1,4to9,11to119

(must be the same for all devices

requiredtoformaLAN).

Note:ChangingtheLAN numberand/ordeviceaddress will

causethecontrollertoreboot.

IfconnectingtoaLANoncurrentloop(withonlyIQ4type

controllers):

▪ Use SET’s IQTool Addresser Applet, and run the

DiscoveryWizard.

▪ Select either ‘Automatic Discovery’ (recommended) or

‘Manual Discovery’. If ‘Automatic Discovery’ is chosen

youshouldthenselect‘DuplicateAddressResolution’.

Automatic Discovery: Thetoolwilldiscoverthedevices,

andattempttoresolveanyduplicateaddresses.

Manual Discovery: Either scan the bar code, or press

theServiceButtonforeachcontroller.

WARNING For /230 variants hazardous

voltagesexistwhentheunitispowered.Take

suitableprecautionsifpressingservicebutton.

Note: If the LAN is not as expected after discovery it could

bebecauseofinstallationrelatedreasons,e.g.wiringfaults,

powerfailure,etc.Checkthedevicesareoperatingcorrectly

and repeat discovery. If there are duplicate addresses add the

devicestothegridmanually,usingnetworkaddressandserial

number.IfnecessaryuseSET’sSystemViewtosettheLAN

number,andIQTooltosettheaddress.

If connecting to a LAN on current loop (with pre IQ4

controllers):

▪ UseSET’sIQToolAddresserApplettomanuallyaddthe

IQ4tothegridusingtheserialnumberandaddress.

▪ UseSET’sSystemViewtosettheLANnumber.

Deviceaddress(O/S)

LANnumber

FixedIPAddress

orHostname(ifDCHP)

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-20187

InstallationInstructions-Conguring IQ422, IQ4NC/00, IQ4NC/12

SetCurrentLoopBaudRate(IQ4NCor../LANvariantsonly,ifcurrentloopnetworkbeingused)

SetupRS232/USBPortAddressing(ifrequired)

CheckLANOKIndicator(notIQ4NC)

2 CONFIGURATION (continued)

IQTo ol Mo nit orA pp letM an ual( T E 2012 98)

SETManual(TE200147)

IQ4CongurationManual(TE201263)

Parameter Range

Supervisorport

0,4to9,11to119

Default=0localaccessonly

USB

Engineeringport

0,4to9,11to119

Default=0temporarilytakesaddress125

UseSET’sIQToolMonitorApplettosettheSupervisorPortor

USBEngineeringPortasrequired.

IQTo ol Mo nit orA pp letM an ual( T E 2012 98)

SETManual(TE200147)

IQ4CongurationManual(TE201263)

If the IQ4xx is to provide connection to the network for

supervisors and tools it is necessary to setup the RS232

SupervisorPortorUSBEngineeringPortasrequired.

Normal operation indication

LANbuiltOK

AttemptingtobuildLAN

Note:ItisnormalbehaviourforLANOKindicatortoextinguish

forupto1minafterdetectingbaudrate,thenilluminate.

Fault indication (EthernetLAN)

UnabletocommunicateonLAN.

Note: Only applies if current loop is

disabledorisnottted.

Fault indication (CurrentLoopLAN)

every15s

Longerthan2minutesindicates

LAN/internetworkcannotbebuilt.

▪

Checkbaudsettingsofalldevicesoncurrentloop–see

step21,andcheckalldeviceconnections.

▪ Ifstillashing,tloopback:

86 87

RX-

RX+

TX-

TX+

IfindicatorturnsOFF,deviceisfaulty.IfON,reconnect

networkandswitchoallotherdevicesonthenetwork.

▪

IfstillOFF,checknetworkcablingforshortcircuitswith

amultimeter(NOTMegger).

▪

IfONswitchonotherdevicesinturnuntilfaultydevice

found (i.e. LAN OK goes OFF),inspect thatdeviceto

determineandandcorrectthefault.

BydefaulttheIQ4xxwillautodetectthebaudrateinuseon

thecurrentloop.Ifalldevicesaresettoautodetectthebaud

rate chosen cannot be guaranteed,in which caseit maybe

necessarytomanuallysetonedevicetoaknownrate.

Use SET’s IQTool Monitor Applet to disable autobaud and

specifythebaudrate.

Module Parameter Range

IQ Lan

network

Autobaud

0(disabled)or1(enabled)

Baud Rate

1k2,4k8,9k6,19k2,38k4

LANOK

(green)

8 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

DownloadStrategy

Check IQ422 or IQ4NC on BACnet (If/BACorIQ4NCandBACnetprotocolcommunicationsrequired)

Test Inputs (NotIQ4NC/.../00)

2 CONFIGURATION (continued)

SETManual(TE200147)

IQ4CongurationManual(TE201263)

SETManual(TE200147)

Switcho Re-connect inputsOpencovers

Closecovers

Switchon

Note: An Ethernet connection is required to download both

strategyandbackdroples.Otherconnectiontypesonlyallow

downloadofstrategyles.

Note: strategy download is not recommended over current

loopwithbaudrate<9k6.

Note: SET will set up the controller’s date and time to that of

thePCduringdownload.However,theymaybesetupfroma

controllerconguredastimemaster.

ConguretheIQ4xxstrategyusingSET,andtestusingSET’s

simulationmode.

Use SET to download the strategy and backdrop le (if

required).

Use SET to check that the IQ4 BACnet functionality is

operatingbycheckingitappearscorrectlyintheSystemView

onitsBACnetnetwork.

Checkdigitalinputs Checkanalogueinputs

LED(yellow)

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018

9

InstallationInstructions-Conguring IQ422, IQ4NC/00, IQ4NC/12

Test Outputs (NotIQ4NC/.../00)

Connect Supervisors/Tools/Display

Panels (ifrequired)

BackupStrategy

Close Panel / Enclosure

CloseRotatingCovers

CongureWebServer

2 CONFIGURATION (continued)

Connect PCs (e.g. for supervisors/tools) and displays as

describedin‘ConnecttoIQ4xx’onpage10.

Connectionofsupervisors,tools,displaypanelsetccanbe

madedirectlytocontrollerviatheRS232Localsupervisor

Port,USBLocalEngineeringPort,WallbusPort,orEthernet

port.ConnectioncanalsobemadeovertheTrendnetwork

overEthernetorthecurrentloop.

Use SET to upload the strategy and compare it with the

strategyheldbySET.

Note: An Ethernet connection is required to upload strategy

andbackdroples.Otherconnectiontypesonlyallowupload

ofstrategyles.

SETManual(TE200147)

Switcho Re-connect outputsOpencovers

Closecovers

Switchon Checkdigitaloutputs Checkanalogueoutputs

LED(yellow)

LOAD

LED(yellow)

LOAD

ConnectiontotheIQ4webservercanbemadeviaHTTP

and/or HTTPS protocol. Where HTTPS is used it will be

necessarytocongureSSLcerticates.

Ifwebaccessisnotrequireditisrecommendedthattheweb

serverisdisabledforsecurity.

IQ4CongurationManual(TE201263)

SETManual(TE200147)

10 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

SwitchOﬀPowertoIQ4xx

Open Top Cover (ifrequired)

Make Connection

PCviaLocalEngineeringPort(USB)

Connect Directly to Controller

PCviaEthernetPort

RJ45

StandardEthernetcable

(Cat5etwistedpair)

max100m(109yds)

Connection use

Notes

IPTool

SET

RequiresvCNC

WebBrowser

Supervisor

RequiresvCNC

PCviaLocalSupervisorPort(RS232)

CABLE/EJ101442

9wayfemale

Dtype

RJ11

ConnectiontotheIQ4xxcanbemadedirectlyviatheRS232LocalSupervisorPort,USBLocalEngineeringPort,orEthernet

Port.Connectioncanalsobemadeoveranetwork(Ethernet).

Connection use

Notes

IPTool



SET

WebBrowser



Supervisor



Connection use

Notes

IPTool



SET

WebBrowser



Supervisor

IQView8viaLocalSupervisorPort(RS232)

IQView8requiresitsownpowersupply.

Note: If local supervisor port address is ‘0’ (default)

communication is limited to the IQ4xx. If non-zero,

communicationispossibleovertheentirenetwork.

RJ11

RD/SDU-IQ2COMMSCABLE3M

USBcable

MicroBUSBconnector

3 CONNECT TO IQ4XX

IQView8

IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018 11

InstallationInstructions-Conguring IQ422, IQ4NC/00, IQ4NC/12

Make Connection (continued)

3 CONNECT TO IQ4XX (continued)

RJ11

24Vdc

Supply

XW/R/IQ

Mustuseexternal24Vsupply

Connect Directly to Controller

RD-IQ, SDU-xcite, IQView4 via Local Supervisor Port

(RS232)

Connect via Ethernet Network

▪ EnsuretheIQ4xxisconnectedtotheEthernetnetwork.

▪ Connecttheotherdevice(e.g.networkdisplayorPC)to

sameEthernetnetwork and ensure an IP connection is

availablebetweenitandtheIQ4xx.

▪ TomakeaconnectionwithSET,asupervisorordisplay

ensureavCNCisavailableinaTrenddeviceonthesame

Ethernet Trend network and connect to the vCNC as

describedinthesupplieddocumentation.

Note:IfconnectingwithIPTool,thePCshouldbeonthe

same Ethernet segment as the IQ4xx.

▪ To make a connection with a web browser run a web

browseronthePCandaccesstheIQ4xxIPaddressor

hostname.

XW/R/IQwirelesssensorreceiver via LocalSupervisorPort

(RS232)

PC Connection use

Notes

IPTool

SET

RequiresvCNC

WebBrowser

Supervisor

RequiresvCNC

Note: Set local supervisor port address to ‘0’ (default) as

communicationislimitedtotheIQ422,IQ4NC/00,IQ4NC/12.

IQView4 requires its own power

supply.

RJ11

RD/SDU-

IQ2COMMSCABLE3M

RJ11

IQView4

RD-IQ

SDU-xcite

StandardEthernetcable

(Cat5etwistedpair)

max100m(109yds)

Hub/Switch

Router

RJ45

RD-WMBviaWallbusPort

RD-WMB

TwistedPairCable

maximumlength60m(200ft)

IQView8

12 IQ422,IQ4NC/00,IQ4NC/12ControllersInstallationInstructions-ConguringTG201265Issue12,24-Jul-2018.

IQ422, IQ4NC/00, IQ4NC/12 InstallationInstructions-Conguring

Please send any comments about this or any other Trend technical

publicationto[email protected]

BuildingDivisionofHoneywellProductsandSolutionsSARL,Z.A.LaPièce,16,1180Rolle,SwitzerlandbyitsAuthorizedRepresentative,TrendControl

SystemsLimited.

TrendControlSystemsLimitedreservestherighttorevisethispublicationfromtimetotimeandmakechangestothecontenthereofwithoutobligation

tonotifyanypersonofsuchrevisionsorchanges.

TrendControlSystemsLimited

St.Mark’sCourt,NorthStreet,Horsham,WestSussex,RH121BW,UK.Tel:+44(0)1403211888,www.trendcontrols.com

Reset Controller

Isolate Power and Disconnect All I/O

Re-congureController

The factory reset will erase the strategy and reboot the

controllerinto its original conguration.While the controller

iserasingthestrategy,theWatchdogandLANOKindicators

will ash alternately. During the reboot all indicators will be

ON. Once this process has completed the Watchdog and

LAN OKindicatorswill go OFF, leaving thePowerindicator

ON.This processmaytakeup to 10minutes depending on

controllertype.

Do not switch oﬀ the controller until the process has

completed.

4 RESETTODEFAULTS

Gotostep1onpage1.

Unplug the Ethernet cable and press and hold down the

service button. While continuing to hold down the button,

switchonthecontroller. Ensurethebuttonremainspressed

for2to5safterpowerisswitchedon.

WARNING FOR /230 versions: Hazardous

voltages exist in this area when the unit is

powered.Thisoperationshouldonlybeperformed

aftertakingsuitableprecautions

Thestrategy,usermodules(passwords,PINsetc),alarmlogs,

andplotsarecleareddownandthefollowingparametersset

todefaults:

LANnumber

outstation address

IPaddressingmode

IP address

subnetmask

UDPport

identier

Router 1

remoteTrenddevices

VirtualvCNCs.

Timeanddateareleftattheircurrentsettings.

2to5s

22 23 24 25

RX+

28 29

WMB

RX- TX+

TX-

RX OK

456 789101112

14 15 16 17 18

123

230V

4 5

24V

0V 0V 0V

986 7

1 2 3

Press

22 23 24 25

RX+

28 29

WMB

RX- TX+

TX-

RX OK

456 789101112

14 15 16 17 18

123

230V

4 5

24V

0V 0V 0V

986 7

1 2 3

Release

Followsteps1,2,4,5and8(onpages1to3)to:

▪ IsolatePower,

▪ OpenPanel,

▪ OpenRotatingCovers,

▪ DisconnectAllI/O,

▪ CloseRotatingCovers.

Trend IQ4NC/12, IQ422, IQ4NC/00 Installation Instructions Manual

Related papers

Other documents