Midmark Elevance® Standard Delivery System Installation guide

English - 1

Cuspidor

Power

Ground

Drain

Console

Side Cover

Console

Cover

Rotation

Stop Pin

Set Screw (second

screw 180°)

Mounting Groove

Bearing

Collar

Magnet

Elevance™ Cuspidor: Console Mounted Installation

Note

Cuspidor is wrapped and sealed in a box to protect the glass.

Carefully inspect parts before installing.

Step 2: Route cuspidor tubing and mounting post into console

bearing. Keep rotation stop pin on the open side of the

bearing collar.

With cuspidor fully inserted, tighten the two set screws

into the mounting groove to secure.

Note Tightness of set screws determines drag on cuspidor rotation.

Step 3: Connect cuspidor power and attach ground to

console frame. Connect like colored tubing.

Connect drain lines with hose clamp.

Language of origin: English

003-2284-99 Rev. C (3/28/12)

WARNING

Always disconnect chair from the power source before removing

any covers. Failure to do so may result in personal injury.

Step 1: Disconnect chair from power supply.

Remove console side cover. Loosen bottom screw and remove

inside console cover.

Tip: Console covers fit up under a lip at the top, pull out from bottom, then down to remove.

Caution

Connect ground wire to ensure system ground continuity.

Failure to do so may result in electric shock.

Style G

midmark.com

Color Page

English - 2

Cuspidor Internal

Components

Constant Flow

Pilot Controlled Flow

Program

Button

Touch (Pilot)

Controls

Limit Switch

Electric

Solenoid

Cuspidor Power

and Ground

Step 4: Align bowl to base press gently into place.

Install cup fill tube, bowl fill tube and bowl

strainer.

Note: May use alternate bowl rinse tube in facilities that have

a 1” (2.5 cm) air gap built into the drain system.

Cup Fill Tube

Bowl Rinse Tube

Bowl and Strainer

Alternate

midmark.com

Color Page

English - 3

4

0

6

0

80

1

0

20

0

1

2

3

5

6

7

4

0

40

60

8

0

1

0

20

0

1

2

3

5

6

7

4

0

Step 5: Remove J-box lid.

Step 7: Water valve connections

A) Connect 1/8” red pilot air tubing to T-Barb.

B) Replace 1/8" fitting on pilot valve with the 1/4" fitting from

the hardware kit. Connect 1/4" blue tubing.

C) Connect 1/8" blue tubing for city water to the T-Cross

fitting if city water option is being used.

Note: Replace 1/8” fitting on the T-Cross fitting with a plug from the hardware

kit, if CITY WATER option is not being used.

Step 6: Use hose clamp to install 5/8" tubing from umbilical

to facility drain.

Water Valve

Assembly

Step 8: Connect red, purple, clear with stripe and yellow

tubing to air valve assembly as shown.

Air Valve

Assembly

Pilot Valve

T-Cross Fitting

T-Barb

To Power

Supply

From Air

Valve

Assembly

From

Umbilical

To Water

Valve

Assembly

midmark.com

Color Page

English - 4

Installation Checklist

Test Verify the following:



1

Cuspidor rotates towards patient and stays in position.

Adjust stop rotation pin or drag if necessary. Reference

Step 2.

2

Console covers are installed and no wires or tubing is

pinched.

3

If cuspidor makes contact with an object while chair is

being lowered, the stops the chair.

4

Pressing Cup Fill or Bowl Rinse button activates the

correct function.

5

There are no leaks in the fill or drain connections or

tubing.

6

Wipe components with a soft dry cloth to remove dirt or

smudges.

Step 10: Connect chair to power supply.

Verify cuspidor operation.

Step 9: Install console covers and place

the lid on the J-box.

Style G

midmark.com

English - 5

Bowl rinse...

Press bowl rinse button to activate the bowl rinse function.

Note: The default bowl rinse function allows water to run for 15 seconds

then stops.

Program a new time for the cup fill function...

A) Press and release program button.

Wait to hear a beep to confirm it is in program mode.

B) Press and hold cup fill button for the desired amount

of cup fill time.

C) Listen for two beeps to confirm program.

Cup fill...

Press cup fill button to activate the cup fill

function. Press and hold button after a cup

fill to “top off” cup.

Note: The default cup fill function allows water to run

for 5 seconds then stops.

Program a new time for the bowl rinse function...

A) Press and release program button.

Wait to hear a beep to confirm it is in program mode.

B) Press and hold the bowl rinse button for the desired

amount of bowl rinse time.

C) Listen for two beeps to confirm program.

Cuspidor Lockout...

Tap program button three times to activate

cuspidor lockout. Listen for a beep to confirm

that the lockout is active.

Tap program button three times to inactivate

cuspidor lockout. Listen for two beeps to

confirm the lockout is inactive.

Cup Fill

Button

Bowl Rinse

Button

Program

Button

Cuspidor Operation

midmark.com

English - 6

This page is intentionally left blank

midmark.com

Page is loading ...

Deutsch - 6

midmark.com

Page is loading ...

Français - 6

midmark.com

Page is loading ...

Español - 6

midmark.com

Page is loading ...

Italiano - 6

midmark.com

Midmark Elevance® Standard Delivery System Installation guide

Midmark Elevance® Standard Delivery System Installation guide

in other languages

Related papers

Other documents