FläktGroup EUVD Air section Installation guide

Type
Installation guide
Fläkt Woods 4620 GB 05.08 1 Specifications are subject to alteration without notice
EU Air Handling Unit INSTALLATION
Connection to duct
Ducts and accessories are connected using a PG guide or
flange.
Gasket EUAZ-10 is required in both cases.
The gasket is ordered separately.
Installation for installation alternatives
02–07, 14–16
(Supplied as two separate block units)
If the exhaust air section is connected to the outlet from
the exhaust air fan, the air distributor EULZ-13 or diffu-
ser EULZ-14 must be installed. See separate instructions.
A. Fit the gasket to the edge ferrule around the hole in
the lower exhaust air section. See Fig. 1.
The gasket is packed with the lower functional sec-
tion.
B. Now position the section which has one damper above
the lower section with two dampers. Make sure that
the holes are aligned accurately.
C. Fit the connecting sleeve duct components from the
inside of the upper block with the self-tapping screws,
as shown in Fig. D. Sealing compound may be appli-
ed to the corners, if required.
Insulation
External dampers are supplied with cover plates over the
linkage arm system. External insulation of the damper is
possible in this way.
Fig. 1
C
B
A
D
Sealing compound
in corner
Control of damper
Actuator
The damper can be controlled with actuating lever
EUVZ-01 (accessory) or actuating lever EUAZ-11
(accessory).
Installation of damper actuators
Damper actuator EUAZ-11 (accessory) is installed in
accordance with the following installation.
Mixing and exhaust air section EUVD
Size 11-53 60,62,71,80 64,73,82,84
bb = 01 3
bb = 02,04,06,09,14,16,18 1 1 2
bb = 03,05,07,15,17,19 2 2 4
bb = 11 3 3
bb = 21 3
bb = 22 1
bb = 23 3
Mixing and exhaust air section EUVD
Fläkt Woods 4620 GB 05.08 2 Specifications are subject to alteration without notice
EU Air Handling Unit INSTALLATION
Torque
The tables below show the required torque.
Damper actuator
The table below show the required number of damper
actuators.
Size 11 20 21 22 30 31 32 33 40 41 42 44 50 51 52 53
Torque,
Nm/damper
bb = 01-16,18,20 4 5 5 6 6 8 8 8 9 10 9 10 10 10 11 11
bb = 17,19 4+4 5+5 5+6 6+7 6+7 8+8 8+8 9+9 10+10 9+10 - 10+10 10+11 11+12 11+12
Size 60 62 64 71 73 80 82 84
Torque,
Nm/damperll
bb = 02-16,18,20 10 11 9 11 9 13 10 11
bb = 17,19 10+10 11+11 2x9+12 11+13 2x9+14 13+14 2x10+15 2x11+16
bb = 21 3x10 3x11 - 2x11+13 - 2x13+14 - -
bb = 22 - - 12 - 14 - 15 16
bbs = 23 - - 2x9+12 - 2x9+14 - 2x10+15 2x11+16
  • Page 1 1
  • Page 2 2

FläktGroup EUVD Air section Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI