2. FläktGroup
  3. EUVC Mixing section

FläktGroup EUVC Mixing section Installation guide

  • Hello! I've reviewed the installation instructions for the Fläkt Woods Air Handling Unit EUV. This document provides detailed information on connecting ducts, installing damper actuators, and using various accessories. I'm here to help answer any questions you have about the installation process or the specifications mentioned in this manual.
  • What connection accessories come pre-assembled on the unit?
    Is the counter flange supplied assembled?
    What's the maximum torque on damper actuator?
Fläkt Woods 4619 GB 05.08 1 Specifications are subject to alteration without notice
EU Air Handling Unit INSTALLATION
Mixing section EUVC
Connection to duct
Ducts and accessories shown in Fig. 1 are connected with
a PG guide or flange.
A duct can also be connected directly to the damper of
the connecting piece.
The following connection accessories: fabric sleeve
EUVZ-02, transition piece EUVZ-03, and protective net
EUVZ-05 are supplied ready assembled on the unit.
Counter flange EUVZ-04 is supplied separately for
installation as shown in Figs. 4 and 5.
Fig. 2 Fig. 3
Fabric sleeve
Transition
piece
PG connection
Fig. 4 Fig. 5
Edged duct
Fig. 6 Fig. 7
Seal
Fabric
sleeve
Transition
piece Seal
Seal
Edged duct
Seal
Counter
flange Counter
flange
Flange connection
Protective net EUVZ-05
Counter flange EUVZ-04
Transition piece EUVZ-03
Fabric sleeve EUVZ-02
Accessories
Fig. 1
Fläkt Woods 4619 GB 05.08 2 Specifications are subject to alteration without notice
EU Air Handling Unit INSTALLATION
Mixing section EUVC
Commissioning
Important!
Ensure that the intake damper is open at the time of
commissioning of the fan. Max. permissible pressure
difference with damper closed = 1000 Pa.
Max. torque on damper actuator 30 Nm.
Insulation
External dampers are supplied with a cover plate over the
shaft journals and the linkage arm system. External insu-
lation of the damper is permitted in this way.
Torque
The required level of torque is indicated in the tables
below.
Size 60 62 64 71 73 80 82 84
Torque, Nm
bb = 11–14 10 11 9 11 9 13 10 11
bb = 15–16 10+10 11+11 2x9+12 11+13 2x9+14 13+14 2x10+15 11+16
bb = 17 10 11 12 13 14 14 15 16
Size 11 20 21 22 30 31 32 33 40 41 42 44 50 51 52 53
Torque, Nm
bb = 01 – 4 5 5 6 7 8 8 7 8 8 8 10 9 10 10
bb = 02–04 4 5 5 6 6 8 8 8 9 10 9 10 10 10 11 11
bb = 12–14 4 5 5 6 6 8 8 8 9 10 9 10 10 10 11 11
bb = 05–06 4+4 5+5 5+6 6+7 6+6 8+8 8+8 - 9+9 10+9 9+9 - 10+10 10+11 11+12 11+12
bb = 07 4 5 6 7 6 8 8 - 9 9 9 - 10 11 11 12
Size 11-53 60,62,71,80 64,73,82,84
Number of damper
actuators
01-07 2 - -
11-14 2 2 4
15-17 - 2 3
Installation of damper actuators
Damper actuator EUAZ-11 (accessory) is installed as
shown below.
/