2. Andersen
  3. 200 Series - Hinged Inswing - 0005473

Andersen 200 Series - Hinged Inswing - 0005473 Service Instructions

  • Hello! I'm your chat assistant, and I've reviewed the Andersen weatherstrip replacement guide for the 200 Series Hinged Patio Doors. This guide provides detailed, step-by-step instructions on how to replace the weatherstrip for various door configurations. I can answer any questions you have about the included parts, tools needed, or the installation process.
  • What parts are included in the weatherstrip replacement kit?
    What tools are needed for weatherstrip replacement?
    How do I install weatherstrip clips?
1
“Andersen” is a registered trademark of Andersen Corporation. All other marks where denoted are marks of Andersen Corporation. ©2006-2006 Andersen Corporation. All rights reserved.
Please read this guide completely before starting. For questions about this and other Andersen® products, call 1-888-888-7020.
For the most current version of this guide visit www.andersenwindows.com. Consult your local building code official for
applicable building codes and regulations. Thank you for choosing Andersen® products.
Please leave this information with homeowner.
A
B
C
D
E
F
G
0005473 BA Revised 03/14/07
Weatherstrip Replacement
Guide
for Andersen® 200 Series Hinged Patio Doors - Inswing
Parts Included
(1) Instruction Guide
(2) Weatherstrip Clips
(1) Weatherstrip
Tools Needed
· Safety Glasses
· Wood Block
· Hammer
· Pliers
• Flat Blade Screwdriver
Read and follow these warnings during installation.
Use caution when working at elevated heights and around unit
openings. Follow manufacturer’s instructions for safe use of ladder
and/or scaffolding. Failure to do so may result in injury or death.
Follow manufacturer’s instructions for safe operation of hand/
power tools. Always wear safety glasses. Failure to do so may
result in injury and/or product damage.
Head Jamb,
Side Jamb/Hinged Astragal
Weatherstrip
Weatherstrip Clip
Passive Panel
Astragal Weatherstrip
(AP, PA Units Only)
AL, AR Units SAL, ASR Units AP, PA Units
4 Verify correct weatherstrip.
1
Interior
1
Interior
1
Interior
2
Interior
3
Interior
Head Jamb, Side Jamb/
Hinged Astragal Weatherstrip
4For head jamb, side
jamb, or hinged astragal
weatherstrip replacement,
proceed to step 4a.
4For passive panel astragal
weatherstrip replacement,
proceed to step 4b.
(AP, PA Units Only)
SAL Unit Shown SAL Unit Shown
Open panel.
or
Passive Panel
Astragal Weatherstrip
2
0005473
Remove weatherstrip to be replaced. Remove weatherstrip
staples or weatherstrip clips if present.
Apply weatherstrip clips 1" from each end of weatherstrip. Crimp clips onto weatherstrip.
Pliers
Clip
Clip
Barbs
Do not
crush barbs
Pliers
Barbs
Do not
crush barbs
Screw
Driver
Staple
1" 1"
4b
Interior
4a
Interior
Hammer
Head Jamb
Weatherstrip
Side Jamb/Hinged Astragal
Weatherstrip
For passive panel astragal weatherstrip, position end flush at bottom of astragal. Tap bottom clip into kerf and work upwards until
seated. Tap in top clip. Installation is finished.
Passive Panel
Astragal Weatherstrip
Hammer
3
For side jamb, position weatherstrip tight at sill. Tap bottom clip into kerf and work upwards until seated. Tap in top clip or For head
jamb weatherstrip, tap in clip at one end and work across until seated. Tap in opposite side clip. Installation is finished.
0005473
Head jamb weatherstrip
runs full width. Side jamb
weatherstrip meets head
jamb weatherstrip from
below.
Wood Block
Astragal
Passive Panel
Astragal Weatherstrip
Hammer
End of weatherstrip
must be tight at sill.
Astragal Sill Cap
End of weatherstrip must be
tight to astragal sill cap.
4
This page has been intentionally left blank.
0005473
/